Download or Print Catalog of LED lights, LED bulbs and LED Lamps for Automotive

S25 BA15D 1142 5730 SMD L.E.D. Bulb. Operates 10-30 Volts AC or DC. Non polarity single filament. Operates positive ground or negative ground. Very bright up to 400 Lumen output. Up to 3 Watt LED comparable to a 25 watt incandescent equivalent. Available in white 6000K and warm white 3000K Red, Green, Blue and Yellow. 360 Degree viewing, CE and Rohs listed, long life up to 30,000 hours. Made with Samsung LEDs. These LED bulbs are extremely reliable for marine, lakes, boat lifts, boats, navigation equipment, ponds, docks, buoys, land scape lighting, vehicles, motorcycles. The BA15D 1142 version is a single filament. For BA15S 1156 version the part number is 98785. For BAY15D 1157 version the part number is 66847. The base has two contacts and the bayonets are even. The base diameter is 15mm. The base has dual contacts only a single filament.

S25 18 Ultra Bright SMD LED Light Bulb. 3 forward firing Ultra Bright SMD LED's and 15 side firing Ultra Bright SMD LED's. Durable, shock, vibration proof, instant On/Off. Monochromatic pure color, low heat generation, virtually unbreakable. This LED measures from top to bottom 1.93 in and a diameter of .73 in. Available in super white 6000K, warm white 3000K, red, yellow, blue and green. 12 V DC. Uses only 3.5 Wattage 30 watt output equivalency. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W BA15D replaces 90 1004 1076 1142 2 1157 G18. CE and Rohs listed. Each 5050 LED emits about 15-20 lumens per chip, the bulb outputs up to 300 lumen output. This bulb fits 1953 Cessna 170 airplane.

LED 2 Watt Projector Lens Light Bulb. This LED Light has a projector lens that helps the LED light be focused and brighter. 12 volt DC. Available in 1156, 1157 and BA15D. This product measures approximately 1.76 inches by 0.77 inches. Up to 140 Lumen output. 120 degree viewing angle. Comparable to a 16 to 20 Watt incandescent bulb. CE and Rohs.

S25 27 5050 Multi Chip Ultra Bright SMD LED Light 12 VDC. 6 forward firing Ultra Bright SMD LEDs and 21 side firing Ultra Bright SMD L.E.D.s. Durable, Dual filament. shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Uses only 4.5 Watt putting out 470 lumens. Available in super white, red, yellow and blue. 12 VDC. 1156 single contact is used for turn signals. 1157 dual contact is used for tail light/ brake light. 1156 single contact is used for turn signals. 1157 dual contact is used for tail light/ brake light. 1156 single contact replaces bulb number. 200 mA @ 14.5 VDC. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W.

18 forward firing LEDs and 21 side firing LEDs. Up to 275 forward Lumens or up to 725 Lux, Up to 150 Lumens or up to 320 Lux side firing. Uses approx. 3.5 watts. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red and yellow. 12 VDC. 1156 single contact is used for turn signals. 1157 dual contact is used for tail light/ brake light. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W. 1157 replaces BAY15D 2057 2357 2397 7528 3496.

18 forward firing LEDs and 6 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white 6000K, red, yellow, green and blue. 12 VDC. 1156 single contact is used for turn signals. 1157 dual contact is used for tail light/ brake light. The BA15D is used for RV, Airplanes and boats. The bayonets are the same, but with a dual contact. Please select BA15D under type. 150mA@12VDC. Equivalent to a 15 to 25 watt incandescent lamp up to 145 lumens forward firing and 50 Up to 50 Lumens side firing. This LED measures approximately 1.64 inches by 1.03 inches by 0.65 inches. Dim-able with a variable voltage supply such as your dashboard dimmer switch.

18 forward firing LEDs and 14 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 12 Volt D.C. 1156 single contact is used for turn signals. 1157 dual contact is used for tail light/ brake light. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W T25 T-25 1016 1034 1130 1152. 1157 1493 2057 2357 2397 7528 3496. This LED bulb is a good fit for tight fitting bulbs. The shape is similar to a incandescent light bulb.

G18 38 SMD 1210 LED Light. 12 VDC. Available in white only. Very nice 38 1210 LEDs. Very bright G18 product uses 2.5 watts of power. 250 lumens. Approximately a 20 watt incandescent equivalent. Base types 1156 and BA15D. Approximate size 2in (height) x .65in (diameter).

1156 1156 BA15D 4 Watt LED Bulb. Works negative ground no polarity for both the BA15S 1156 or BA15D 1142. The BAY15D works only negative ground. Up to 250 Lumen output for taillight and up to 300 Lumen output for brake light or a single filament bulb. The BA15S 1156 and BA15D 1142 bulb is a single filament, the BAY15D 1157 bulb is a dual filament. Comparable to a 35 watt incandescent automotive bulb. Vibration proof, glass lens, just like a normal bulb, but it is long life CREE 4 watt led chip. Up to 400 Lumen output. 12.8 VDC @ .224 Amps = 2.56 watts. Not Dimmable. A very nice "old fashion" looking bulb perfect for those who want to switch to LEDs but like the "old fashion" look. 120 Degree viewing angle. Rohs listed. CE certified. Long life up to 30,000 hours. Comparable to 35 to 45 watt incandescent bulb. The BA15D base works by applying voltage to the two contacts on the bottom.

Uses 3.3 watts. 120 Lumen (25-30 Watt) output Available in super white 6000-6500 Kelvin and Warm White 3000-3500 Kelvin. 10,000 hour life. 120 Degree viewing angle. Operating voltage 12 VDC. 2 inches in length and 1 inch x 1 inch in width at the top. High tech heat sink to make the LED Light last longer. Designed for automotive, RV and marine uses along with many others. Available with BA15D base. 240mA@12 VDC. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W. 1157 replaces BAY15D 2057 2357 2397 7528 3496. BA15D replaces 90 1004 1076 1142.

S25 L.E.D. bulb, super bright 5730 SMD, has 6 chips forward firing, 12 chips side firing. CE and Rohs listed, long life up to 30,000 hours, available in white 6000k and warm white 3000k. Forward firing Lumens is up to 300 Lumens. 360 degree viewing angle. Each 5730 led chip outputs up to 50 Lumens. Consumes up to 3 watts@13.8 volts. Made with Samsung led's. Uses up to 180mA@13.8 VDC. Great for negative ground vehicles, trucks and motorcycles.

300 Lumen output, 240 mA current @ 12 VDC. 2.69 Watt input power consumption, 25 Watt equivalent light output. 6000-6500 Kelvin Super White or 3000-3500 Kelvin Warm White. 30,000 hour life. 120 Degree viewing angle. Operating voltage 12 Volt DC. 2 inches in length and 1.06 inches x 1.91 inches at the top. High tech heat sink to make the LED Light last longer. Designed for automotive, RV and marine uses along with many others. Each 5050 smd can output to 25 Lumens. Comes in 3 bases BAY15D, BA15D and BA15S. CE and Rohs.

S25 5 Watt LED Bulb, 60 2835 LEDs, very bright up to 500 lumen output, has both foward and side firing leds, good size comparable to a normal incandescent light bulb, up to 500 lumen output, long life up to 30, 000 hours, CE, Rohs listed, 12VC L.E.D's. Availbe in white, warm white, red, green, blue and yellow/amber. Made with Samsung L.E.D's for a high quality product.

Uses 2.69 Watt input power consumption. Has an estimated light output of 21 Watts at 240 Lumens. Operating voltage 12 VDC, operating current 0.240 Amps. 120 Degree viewing angle. Available in super white and warm white. Measures 1.15 inches from top to bottom and the square measure 1 inches x 1 inches. This LED Light has a high tech heat sink designed for the auto, RV and marine environment to help the LED's operate cooler. No UV light, makes lenses and the area that is illuminated last longer. Use less power and save energy, and less UV damage. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W. 1157 replaces BAY15D 2057 2357 2397 7528 3496. BA15D replaces 90 1004 1076 1142.

1156 led bulb operates in a positive ground or negative ground from 6 to 12 volt AC or DC system. G18 S25 2.6 Watt L.E.D. bulb. Has 6 forward firing and 7 side firing LEDs. The life is up to 30,000 hours. Available in white 6000 Kelvin, warm white 3000 Kelvin, Red 625 nm Green 526 nm, Blue 464 nm& Yellow 594 nm. Available 1156 BA15S. Great bulb for tight fit, this small high power led is great for all applications, very bright up to 300 Lumen output in 360 degree illumination. This bulb will operate in classic old vintage antique cars positive earth, trucks and motorcycles 6 volt low voltage. This bulb is non polarity, no polarity you can use it in positive chassis and negative chassis cars, trucks an motorcycles. Comparable to a 25 to 30 watt incandescent, very small fits in tight bulb locations. CE and Rohs listed. Uses approximately 100mA @ 13.8 Volts.

S25 6 Watt LED bulb, up to 400 lumen output, Comparable to a 45 watt incandescent bulb. MCOB technology, 12 VDC, CE and Rohs listed, long life up too 30,000 hours, 360 degree lighting. Available in white 6000K only. Great for replacing standard incandescent automotive lighting. Draws .230 Amps @ 13.8 VDC.

1154 led bulb for 6 Volt. The led bulb works for both positive ground chassis or negative ground chassis. 1154 LED bulb is a 6v led bulb. Up to 320 Lumen for brake light and up to 240 Lumen for tail light. This bulb is same as 1154 bulb that has two brightness levels or two filaments one is for the tail light and the other is for the brake light. This bulb works great for non polarity 6 volt positive or negative ground. The LED bulb is small in size so it fits in G18 and S8/S25 bulb size applications. Made with the highest quality Samsung 5730 SMD led chips. Operates voltage up to 7.4 Volts. Voltage higher than 7.8 Volts will damage this bulb and voids warranty. The white 6000K bulb starts to light at at 3.5 Volts. This bulb will work the same as a incandescent bulb without the power drain or the filament breaking. Uses about 290mA @ 6.8 Volt for brake light and 90mA @ 6.8 Volt for taillight.

Available in super white, warm white, red, yellow amber, green and blue. Approx .08 mA @ 12.8 Volt DC and 1 watt @ 12.8 VDC power . Equivalent to a 10 watt incandescent bulb. Up to 90 lumens. The bayonets are the same height, but with a dual contacts, please select BA15D under type. Long life up to 30,000 hours. The overall length is 1.25 inches and the diameter is .59 inches. This LED bulb is dimmable with a variable 12 VDC power supply. Fits most bow lights. The white is very bright. For 12 Volt systems that are negative ground. Great for airplanes, marine or recreational vehicle use. The white is created by a blue led with material added to the blue led to make the color changed to white or warm white. The white 6000k is brighter than the warm white 3000K by 5 to 10%. The led colors are created by the material used to create the led.

1156 1157 20 Super Flux LED Light. 5 forward firing super flux LED's and 15 side firing super flux LED's. Approx 350 side firing & 150 forward facing lumens. Bulb is 2.14 inches in length(from top to bottom) and 1 inch in diameter. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow and blue. 12 VDC, ~ 5 watt . T25 base style. 1156 single contact is used for turn signals. 1157 dual contact is used for tail light/ brake light. 1156 single contact replaces bulb number. 360 mA @ 13.8 VDC. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W T25 T-25 1016 1034 1130 1152.

S25 21 SMD LED Bulb. This bulb is exactly shaped like the original incandescent bulb. You should have few issues installing this bulb. 12 Volt, Trip chip SMD, 21 LEDs.

Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat, virtually unbreakable. Available in super white, red, yellow, 12 VDC. The red and yellow will have 41 LEDs and the white has 31 LEDs. The unit fits in a 1" hole then opens up. Uses approximately 4 watts of power. The Spider LED Light directs the LED Light into the automotive lens perfectly. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W. 1157 replaces BAY15D 2057 2357 2397 7528 3496. Up to 330 Lumen output, 250 forward firing Lumens and 80 rear firing Lumens. Dimmable with a variable voltage supply. Comparable to a 25 Watt incandescent bulb. CE and Rohs.

4 Watt High Power LED Light Bulb. This LED bulb has 4 1 Watt High Power LEDs. Available in white only. Base styles 1156 and 1157 and BA15D. This product measures 1.48 inches by 0.98 inches. Up to a 30 watt incandescent equivalent. 12VDC. BA15D is a dual filament or dual circuit, 1158. Up to 280 Lumen output. 120 degree viewing angle.

s25 19 led bulb. Has 19 forward firing LEDs. Durable, shock and vibration proof. The s25 bulb is instant On/Off. Monochromatic (pure) color. The lamp has low heat generation ie cool to the touch. Measures 26 mm in diameter and 45 mm from top to bottom. Equivalent to 18 to 24 watt incandescent bulb. Long life up to 30,000 hours. Available in super white, red, yellow, green and blue. Approximate single contact usage is .04mA. Dim-able with a variable voltage supply such as your dash board dimmer switch. Approximate dual contact usage id .17mA. 12 VDC. 1156 single contact is used for turn signals. #1156 bulb used for turn signal or parking light. #1157 dual contact is used for tail light/brake light.

130 Lumen output, .15 mA current @ 12.8 VDC. 2.69 Watt input consumption, 28 Watt equivalent output. 6000-6500 Kelvin Super White or 3000-3500 Kelvin Warm White. 10,000 hour life. 360 Degree viewing angle. Operating voltage 12V VDC. 2 inches in length. High tech heat sink to make the LED Light last longer. Designed for automotive, RV and marine uses along with many others. Now with Warm White and BA15D base configurations for RVs and boats. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W. 1157 replaces BAY15D 2057 2357 2397 7528 3496. BA15D replaces 90 1004 1076 1142. Philips 416719 Landscape Lighting 13-Watt S8 12-Volt Bayonet Base Light Bulb. Comparable to 15 to 25 Watt incandescent bulb.

1 Ultra Bright 3 Watt LED. 10 Ultra Bright SMT LEDs. Each Ultra Bright SMT LED has 2 LED chips. 3 Watt output. 12 VDC. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in red, yellow, super white. 1157 dual contact is used for tail light/ brake light. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W. 1157 replaces BAY15D 2057 2357 2397 7528 3496.

9 forward firing LEDs and 9 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 12 VDC. .17 Amps@12 VDC. The size is 1" diameter and 1.44 length. 1156 single contact is used for turn signals. 1157 dual contact is used for tail light/ brake light. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W. 1157 replaces BAY15D 2057 2357 2397 7528 3496. 360 degree illumination. Comparable to a 15 to 25 Watt incandescent bulb. CE and Rohs listed. Long life up to 30,000 hours. Up to 180 Lumen output.

1156 1157 36 LED Light. 36 Super bright LED's. 18 Forward firing and 18 side firing, using 5mm LEDs. Available in white, green, red, blue and yellow. Only uses .25 mA@13.8 VDC. Size top to bottom 2 Inches, diameter 1" Inches. Forward firing 725 Lux, side firing 275 Lux. 1156 single contact is used for turn signals. 1157 dual contact is used for tail light/ brake light. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W. 1157 replaces BAY15D 2057 2357 2397 7528 3496.

Uses CREE Q5 5W LED. 120 View angle. 5500-6500 Kelvin white. Clear lens, great for backup led lights. 9 to 15 VDC operating voltage. 1156 only. This LED measures approximately 2.06 inches by 0.97 inches by 0.65 inches. Please note that the red body is for a red LED and the white for white LED.

LED Cree 5 Watt high power LED Light. Uses a CREE Q5 LED. 180 degree viewing angle. Dimpled lens to disperse light. Wide voltage range 9 to 15 volts D.C. Only base 1156 (BA15S). This LED measures approximately 2.06 inches by 0.97 inches by 0.65 inches. Please note that the red body is for a red LED and the white for white LED.

G18 LED Light. 8 LEDs 8 forward firing. Available in super white, red, yellow, green and blue. 12 VDC. Single circuit BA15S base and dual circuit BA15D base. 20mA@12VDC. 1.35 Inches in overall length and 0.75 Inches in width. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W BA15D replaces 90 1004 1076 1142

Up to 850 lumen output. S25 (1156) uses 4 (2.38 watt) LEDs for a total of 9.5 watts. Very bright and 360 degree viewing angle/beam. 12-24VDC wide voltage operation. 300mA Good (gold colored aluminum) heat sink to dissipate the warmth generated by 9.5 watts. Round glass lens on forward firing LED and no lens on side firing LEDs Approx.: 1.95" x 0.97"

18 forward firing LEDs and 6 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 24 VDC. Draws .05 mA @ 24VDC. 1156 single contact is used for turn signals. 1157 dual contact is used for tail light/ brake light.

The 5 led light bulb S25 is 12 Volt DC .02 amps of 12V power consumption that’s .24 watts. Its size is 1.28in x .72in and is Available in white (6000K) only, IP50, 5 DIP LEDs; you get 70 Lumen for up to 40,000 hours (70Lm/.24Watts). It comes in the 1156 base only great for use in RVs, Cars, Trucks, and Buses. Great for extremely low power long life application. Replaces T25, T-25, 1073, 1093, 1141, 1147, 1159, 1259, 1295, 1383, 1459, 1619, 1651, 1680, 2056, 3496, 5007, 5008, 7008, 7506, 7806, 7527, 1156, 1759, 3497 and 1156-18W

BAY15D LED G18-S25. This product works when you apply 0 to the base and 7 Volts to the tip the LED will light. This product will work 7 Volt D.C. applications. 1157 bases. BAY15d. 2.6 watt output, each led 1/2 watt. Up to 250 lumen output.

1142 LED Miniature BA15D S8 shape. Operates positive chassis or negative chassis 6 to 12 Volts. BA15D DC Bayonet 2.6 Watt L.E.D. bulb. Has 6 forward firing and 7 side firing LED's. Up to 30 CP. The LED bulb has a single filament brightness. This bulb will operate in a non polarity 6 volt systems positive chassis or negative chassis. The life is up to 30,000 hours. Available in white 6000 Kelvin, warm white 3000 Kelvin, Red 625 nm Green 526 nm, Blue 464 nm& Yellow 594 nm. Available BA15D. Please see 78865 for BA15S or 1156. Great bulb for tight fit, this small high power led is great for all applications, very bright 260 Lumen output in 360 degree illumination. This bulb will operate in vintage and classic old cars with positive grounds or positive chassis car or bike, low voltage. Comparable to a 20 watt incandescent, very small fits it tight bulb locations. CE and Rohs listed.

6 LED Light Bulb. Available in white only. Available in 1156, 1157 and BA15D. 12 Volt DC @ .72 Watts. This product measures approximately 1.28 inches by 0.72 inches.

6V AC or DC. Use in positive ground or negative ground. 18 forward firing LEDs and 6 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat, virtually unbreakable. Up to 16 CP candle power output. Available in super white, red, yellow, green and blue. 6 VDC/ VAC. Approximate size is 1.57in x 1.03in. The max voltage is 8 volts. This 6 Volt bulb is designed for vintage vehicles and motorcycles for both negative ground chassis from post World War II and positive chassis from pre World War II. This product works when you apply 0 to the base and 6 Volts to the tip or if you apply 6 Volt to the base and ground to the tip the LED will light. This product will work both 6 Volt A.C. and 6 Volt D.C/A.C. applications. 1156 & 1157 bases. BA15S or BAY15d. Uses 1.8 watts, 15 watt incandescent equivalent, Up to 200 Lumen output.

Ultra Bright LEDs. Very low profile for tight fitting applications. Up to 180 Lumen forward firing and up to 70 Lumens side firing. Uses 30mA@12VDC for BA15S or BA15D or the high beam for BAY15D. This LED bulbs has 36 light emitting diodes. Available in super white, yellow, green, blue. Available in bases 1156 Single Circuit, 1157 Dual Circuit, BA15D Single Circuit. 12V. 30,000 hours of LED life. Luminous efficacy is 2000. 270 degree beam angle. Comparable to a 25 to 30 Watt incandescent bulb. 1 chip per led. The BAY15D has offset bayonets. The Lumen output for high beam is up to 180 Lumens while the low beam is up to 150 Lumen output. This bulb only works on negative ground vehicles. The base diameter for BA15S, BA15D or BAY15D is 15mm diameter. This product measures approximately 1.70 inches by 1 inch.

60 Ultra Bright SMT LED Light. 12 forward firing super flux LED chips and 48 side firing super flux LED chips, total 60 LEDs. Bulb is 1.85 inches in length(from top to bottom) and .95 inch in diameter. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in White 6000K, Warm white 3000K, Red 625nm, Yellow 594nm. 12 VDC. T25 base style. 1156 single contact is used for turn signals. 1157 dual contact is used for tail light/ brake light. 1156 single contact replaces bulb number. .29mA @ 13.8 VDC. Up to 430 Lumens comparable to a 35 watt incandescent bulb. Uses about 4 watts.

6 Watt High Power 1156/1157 LED Light Bulb. Has 6 1 watt high power led's. 2 Forward firing and 4 side firing. 12 Volt DC only. Available in white only. This led measures 1.35 inches by .82 inches. Comparable to a 50 Watt incandescent bulb. 120 Degree viewing angle. For negative ground vehicles, motorcycles and trucks. Up to 200 Lumen output forward firing and 200 Lumen output side firing.

9 forward firing LEDs and 18 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 12 VDC. 1156 single contact is used for turn signals. .26 mA @ 13.8VDC. The size is 1" in diameter and 1.70" long. 1157 dual contact is used for tail light/ brake light.

6 Forward firing LEDs. Durable, shock, vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white 6000K, red, yellow. Super White 1156 is only available in the smaller version pictured above. The rest of the colors and bases are only available in the larger bulb pictured. 12 VDC. 1156 BA15S base single contact is used for turn signals. 15mm diameter with even bayonets. Single contact on the bottom. Up to 100 Lumen output. This bulb is dim-able with a variable voltage supply such as your dashboard dimmer switch. CE and Rohs. Comparable to a 15 to 25 Watt incandescent. Approximately 120 degree viewing angle. 1157 dual contact is used for tail light/ brake light.

3 LED Light Bulb. Very low profile LED Light. Great for hard to change light bulbs. Available in white only. Uses .25 Watts at 12 VDC. This LED measures approximately 1.25 inches by 0.60 inches. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 #89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W T25 T-25 1016 1034 1130 1152 1157 1493 2057 2357 2397 7528 3496 BA15D replaces #90 #1004 #1076 #1142 CE and Rohs certified. Forward firing leds. Up to 30 Lumen output. Comparable 4 to 14 watt incandescent. 45 degree viewing angle.

18 forward firing LEDs and 6 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat, virtually unbreakable. Available in super white, red, yellow, green and blue. 6 VDC. Approximate size is 1.57in x 1.03in. This 6 Volt bulb is designed for negative ground chassis from post world war II. The center contact is Plus 6 Volts and the bayonet body is negative or zero volts ground. This bulb will not work in most pre world war II 6 Volt cars except for Model T Fords from 1909 to 1927 are negative ground. Please see part number 95634 to operate in both pre and post World War II vehicles. Equivalent to a 15 watt incandescent putting out approximately 145 lumens.

54 SMD 3528 (1 Chip) LED Light. Up to 200 Lumen output forward firing and up to 90 Lumen output side firing. G18 available in BA15D, 1156 BAY15D and BA15S. 12 VDC. 9 forward firing and 45 side firing. Only in super white. Ultra Bright surface mount technology. Approximate size of this LED is 1.89in (height) x .77in (diameter).

25 Forward firing LEDs. Durable. Dimensions are, The square is 37.4mm square Roughly 6.5mm thick. The wire length is 60.0mm in length. And the base length is 21.6mm and diameter 15mm. Shock and Vibration proof. Instant on/off. monochromatic (pure) color. low heat. virtually unbreakable. 12 VDC. Uses 180 mA. Equivalent to 430 lumen output. Available in Super White, Red and Amber Yellow. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W. 1157 replaces BAY15D 2057 2357 2397 7528 3496. Comparable to a 25 to 30 Watt incandescent bulb. All the leds are forward firing for maximum led light output.

Miniature LED Bulb BAY15D great for 6 to 12 Volt DC applications, 6V to 12V negative ground or negative chassis. Available multiple colors, please check. 360 Degree viewing angle. Uses the latest technology 5730 SMD Samsung chips up to 320 Lumen output for brake light. This product is polarity sensitive. Please see other same product that is non polarity sensitive. Uses about 2.6 watts. Up to 135 Lumen output for taillight. 6 to 12 Volt DC applications only. Please make sure your application only provides 6 up to 12 volts max DC under a LED load condition. CE and Rohs listed. Made with quality 5730 SMD Samsung led's for long life. This bulb is very bright two filament the brake light and the tail light. This LED bulb is not dim-able. Comparable to a 25 to 30 watt incandescent bulb.

1158 Miniature LED Bulb for old vintage and classic cars. 2 filament or brightness levels. For Negative ground vehicles. Operates from 6 to 12 volts DC. 360 degree illumination. This is a BA15D base product. Long life up to 30, 000 hours. Latest technology 5730 SMD LED chips for very bright and long life. The bulb fits the outline of a normal incandescent bulb. UP to 270 lumen output for tail light, up to 320 Lumens for brake light. 1158 for older negative chassis 6 to 12 volt cars or motorcycles, tractors. The difference between a 1157 and 1158. The 1157 the bayonets are offset while the 1158 are the same height. The diameter of the base is 15mm so it will fit your fixture if 1158 style. Long life up to 30,000 hours. Comparable to a 25 Watt to 35 Watt incandescent light bulb. If the tail light is brighter than the brake light please rotate the bulb 180 degrees. CE and Rohs.

81 LED Bulb 6 Volt Positive Chassis or Negative Chassis Miniature bulb. This bulb will work on AC or DC voltage. The maximum bulb length is 1.24 inches and the maximum diameter is is .75 inches. This will fit the small size of a #81 light bulb. BA15S single contact. G6 single contact bayonet LED. C-6, C-2R filament design compatible, single filament Uses only 1 Watt at 6 volts. Uses very low power. The profile is very small to match the profile of the #63 bulb. The light output is up to 90 Lumens the #63 bulb has a rated output of 3 candle power CP, the LED is up to 6 candle power so about twice as bright as stock light bulb. This bulb is available in White 6000K, Warm White 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Long life up to 30,000 hours.

1154 Miniature LED Bulb 6 Volt. This lamp will operate either Positive Ground or Negative Ground. BAY15D dual contact offset indexed bayonet LED. Dual filament. The #1154 has both a tail light and a brake light. There are two contacts on the bottom. One contact is for taillight. One contact is for brake light. The base is 15mm diameter. The bayonets are offset. Uses up to 1 Watt at 6 volts. Approximately uses 166mA @ 6 Volts. Uses very low power. The profile is very small. The overall length is 1.25 inches and the diameter is .59 inches. The light output is up to 200 Lumens for brake and 150 Lumens for taillight. The bulb brake light has a rated output of up to 16 candle power CP. The taillight has a rated output of up 11 candle power CP. This bulb is available in White 6000K, Warm White 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Long life up to 30,000 hours.

1157 led bulb operates 10 to 30 Volts DC. Up to 600 Lumens for the brake light. The taillight up to 450 Lumens. This led bulb is DC so it will operate in negative chassis. The light bulb is not dim-able due to the wide voltage operation. The bulb has a rated life up to 30,000 hours. The bulb only uses 3 Watts of power and is comparable to a 27 Watt incandescent bulb. The viewing angle is 360 degrees. This is the BAY15D version BA15D 1142 version is part number 25454 for 1156 please order 98785. Available in white 6000K and warm white 3000K Red and Yellow. Compatible with S8 S25 P21W lamps. Up to 3 Watts, Up to .25 amps @ 12 volts.

1142 LED BA15D 6 Volt Positive Ground and 6 Volt Negative Ground. Up to 150 Lumen forward firing, up to 20 Lumen side firing. Available in warm white 3000K and White 6000K. Comparable to a 25 Watt halogen bulb. Approximate size is 1.57in x 1.03in. BA15D base has a single filament. The bayonets are parallel or even and two contacts on the bottom. The diameter of the base is 15 mm. 360 degree illumination excellent choice for reflectors and lens. Dimmable with a variable voltage supply such as your dashboard dimmer switch. This is a single filament led bulb. To apply power you connect ground the one contact and apply plus 6 Volt to the other contact. Comparable to a 15 to 25 Watt incandescent bulb. CE and Rohs.

G18 3 1/2 Watt High Power LEDs. Very Low profile for a 1.5 Watt G18 LED Light Bulb. Available in white only. Available bases BA15D, and BA15S (1156). 12 Volt DC . This LED measures approximately 1.08 inches by 0.66 inches by 0.60 inches. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 #89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W T25 T-25 1016 1034 1130 1152 1157 1493 2057 2357 2397 7528 3496 BA15D replaces #90 #1004 #1076 #1142

1156 BA15S 10 to 30 Volts AC or DC. Positive or negative chassis. Up to 300 Lumen output. Available in white 6000 K and warm white 3000 K Red and Yellow. Long life up to 30,000 hours. CE and Rohs listed. This base is single contact BA15S or 1156 male base. Since this led bulb is wide voltage from 10 to 30 Volts it is not dim-able. Please order 24545 for BA15D, 66847 for BAY15D and 98785 for BA15S. Comparable to a 25 to 30 watt incandescent light bulb. Works great for red and green wingtip general aviation aircraft. Available in White 6000K, Warm White 3000K, Red 625 nm, and YellowAmber 594 nm. Not PMA. Up to 3 Watts, Up to .25 amps @ 12 volts. Compatible with: RA-7512 14V W-1290 28V GE 1683

1158 Bulb 6V 24 LED. Works either 6 Volt positive or negative ground. Approximate size is 1.57in x 1.03in. Up to 180 Lumen output. Works great for older pre World War II vehicles. Available in White 6000K, Red, Green, Blue, Yellow. Dual filament BA15D base. If tail light comes on brighter than brake light must rotate the bulb 180 degrees. Comparable to a 20 to 25 Watt incandescent bulb. The base is BA15D which means there are two contacts on the bottom. The bayonets are parallel. If the tail light is brighter than the brake light please rotate the lamp 180 degree's. Uses around 1.8 watts. The Lumen output for low is up to 160 Lumens. The high is up to 210 Lumens. The low beam side firing is up to 40 Lumen. The low beam forward firing is up to 120 Lumens. The high beam side firing is up to 53 Lumen. The high beam forward firing is up to 110 Lumen.

Up to 350 lumen output. S25 12 Watts 5 leds, 360 viewing angle. Wide voltage range 12-24VDC. Glass lens on forward firing LED(50 lumen) and no lens over side firing LEDs(100 lumens). Aluminum heat sink for good heat dissipation. Available in 1156 & 1157 bayonet bases. Only available in white 6000K. Approx.: 1.91" x 0.78"

82 LED Bulb. BA15D Base. 6 Volt Positive Ground or 6 Volt Negative Ground. Up to 200 Lumen output. Up to 15 Candle Power. The maximum length is 1.25 inches and the maximum diameter is .75 inches. Comparable to a 10 to 25 Watt incandescent bulb. The L.E.D. bulb C-6 filament design. Single Filament. Uses up to 2 Watts @ 6 Volts. The base is BA15D with even bayonets. The lamp only has one brightness level. The bulb is dim-able using variable voltage supply such as dashboard knob. Great for license plate, turn, tail, brake, dome, dashboard, instrument panel lamps. The LED color is created by the material of the LED so it looks real nice monochromatic. The available colors are White 6000K, Warm White 3000K, Red 626nm, Green 526nm, Blue 646nm and Yellow 594nm. The old light bulbs were painted. Very low profile to fit Ford Model A cowl light. Long life up to 30,000 hours.

1651 LED Bulb for lantern's. These bulbs work either positive ground or negative ground. Vibration resistant so you do not have to worry about broken glass. 360 degree illumination. Up to 360 Lumens comparable to a 25 to 30 Watt incandescent. Uses only 2.6 Watt's. The filament design is C-6. The base is Single Contact Bayonet BA15S. Drop in replacement for #1651. The shape fits within the standard S8 size so you should not have worry about fit if the current size is S8. Used for battery operated camping lanterns and solar lighting. Long life up to 30,000 hours. The bulb is available in White 6000 Kelvin and Warm white 3000 Kelvin. Solid state nothing can easily break when you are camping, 4 wheeling, hunting, fishing and boating. Great for off the grid since there is no worry of a broken filament. Will be ready to go when you need it.

9 forward firing LEDs and 27 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 12 VDC. 1156 single contact is used for turn signals. .31 Amps @13.8 VDC. The size is 1" diameter and 1.565" length. 1157 dual contact is used for tail light/ brake light. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W. 1157 replaces BAY15D 2057 2357 2397 7528 3496.

9 forward firing LEDs and 18 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 12 VDC. 1156 single contact is used for turn signals. .23 Amps @ 13.8= 4 Wattage equivalence. The size is 1" in diameter and 1.65" long. 1157 dual contact is used for tail light/ brake light. Great for negative ground vehicles, motorcycles or scooters. 360 degree illumination. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W. 1157 replaces BAY15D 2057 2357 2397 7528 3496.

63 LED Bulb 12 to 14 Volt BA15S Base. Works positive ground or negative ground. Operates from 12 to 14 volts AC or DC. Long life up to 30,000 hours. Up to 12 CP or 240 Lumens. 120 degree viewing angle. Designed for old sockets that have fingers. Dimm-able with a variable AC or DC power supply such as your dashboard dimmer switch. Comparable to a 25 Watt incandescent bulb. Operates cool to the touch. Great for vintage and classic cars that have been modified from 6v or 8v to 12v. CE and Rohs. The shape is G6.3.0 MSCP. The filament design is compatible with C-6. This bulb is a true 63 compatible since the board is mounted inside the ba15s base. The overall length M.O.L. is .888 inches. The maximum bulb diameter is .590 inches. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow/Amber. Compatible with: T18 631 63lldp2

For BMW's. Bayonet looks like a "V". 24 LED Light. 18 forward firing LEDs and 6 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 12 VDC. This product measures 1.78 inches by 1.02 inches. Compatible with: ry10w

1154 Bulb LED BAY15D Base 8 Volt 2.6 Watt. Works either negative ground or positive ground. Long life up to 30,000 hours. Uses only 2.6 Watts. Comparable to a 25 Watt halogen bulb. Has dual filament low beam and high beam. The bayonets are offset. The base has 2 contacts. The base diameter is 15mm. The MOL is 1.47". The MOD is .78". Available in White 6000, Warm White 3000K, Red, Green, Blue and Yellow. CE and Rohs. Up to 320 Lumen for brake light and 240 Lumen for tail light. This bulb is dim-able using a variable voltage supply. Use load equalizer per each led bulb that used in a turn signal circuit. Please use our solid state flasher with load equalizers. Works from 6 Volts up to 10 Volts. CE and Rohs.

1158 Led Miniature Bulb ba15d base led bulb. 12 Volt. Has 30 5730 high output leds. Up to 650 Lumen output high beam and up to 500 Lumens output on low beam. The ba15d base is 15mm diameter, bayonets same height and has two contacts on the bottom. The bulb is considered a dual filament bulb. One filament is low beam and one filament is high beam. The leds are aligned for maximum led light aligned with the reflector. This bulb is smaller than the original light bulb so you should not have any installation issues. Long life up to 30,000 hours. Dim-able using a variable voltage supply such as your dashboard dimmer. This led lamp is non polarity so it will operate in both positive ground or negative ground cars, trucks and cycles. Up to 500mA@12 Volt. Up to 6 Watts high beam. Up to 4.5 Watts low beam.

12 Volt non polarity, up to 950 Lumen output for high beam. Up to 700 Lumen output for low beam. Dual filament. The bayonets are parallel. Works either 12 Volt positive ground or 12 Volt negative ground. 60 5730 SMD's very bright. Long life up to 30,000 hours. The leds are optically aligned with the reflector for maximum led light output. This led headlamp as 20 forward firing and 40 side firing led's. This bulb is non polarity sensitive so you can use it in both positive or negative ground vehicles, motorcycles and trucks. The bulb is dim-able using a variable voltage source such as your dashboard dimmer switch. Comparable to a 35 to 55 Watt incandescent. Available in White 6000 K, Warm White 3000 K. UP to 70 CP for the high beam. The maximum overall length M.O.L is 1.944". The maximum diameter is 1.05". Up to 300 Lumen for forward firing for the high beam.

63 LED Bulb 8 to 9 Volt BA15S Base. Designed for 8 Volt Fords. Works both positive ground or negative ground. Up to 18 CP or 240 Lumen output. 120 degree viewing angle. Long life up to 30,000 hours. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow. Single Contact, Single Filament BA15S. The bayonets are even and has one contact and the bottom. The base diameter is 15mm. The bulb is made very low profile to work when used in old sockets that classic and vintage cars have. The bulb is dimmable. Comparable to a 25 Watt incandescent bulb. The shape is G6.3.0 MSCP. The filament design is compatible with C-6. This bulb is a true 63 compatible since the board is mounted inside the ba15s base. The overall length M.O.L. is .888 inches. The maximum bulb diameter is .590 inches. CE and Rohs listed. Compatible with: GM #142303 Mazda bulb GE 63 #1133 TS67

1158 LED Miniature Bulb 12 Volt non polarity dual filament bulb. Uses 30 5730 smd leds. The bulb is dim-able using a variable voltage supply such as dashboard dimmer. The leds are aligned to your reflector for the best led light output. CE and Rohs listed. Long life up to 30,000 hours. Comparable to a 27 to 37 watt incandescent lamp. Fits in the normal outline of the bulb you are replacing for easy installation of a led bulb. Up to 700 Lumen output for low beam up to 900 Lumen for high beam. Works either positive ground or negative ground cars, trucks or scooters. Available in white 6000k, warm white 3000k, red, green, blue and yellow. Up to 55 CP for low beam up to 70 CP for high beam.

LED headlamp 12 volt BA15S base. Single filament. Up to 950 Lumen output. BA15S base two bayonets same height and 1 contact in a 15mm base. This bulb works either 12 Volt positive ground or 12 Volt negative ground. CE and Rohs listed. Comparable to a 37 to 57 Watt halogen bulb. 360 degree viewing angle. The leds are aligned with your reflector for maximum led light output. Available in white 6000k and warm white 3000k. Dim-able with a variable voltage supply. Smaller than a normal light bulb so its easy to install. Long life up to 30,000 hours. This is a single element bulb so its on and off. The M.O.L. Maximum overall length is 1.944 inches. The diameter is 1.058" Compatible with: Ryobi and Husqvarna Lawn Tractors and Mowers Husqvarna 532004152

LED Headlight 12 volt non polarity either positive ground or negative ground chassis. The base is BA15S, which has parallel bayonets same height and a single contact in a 15mm base. Long life up to 30,000 hours. Up to 650 Lumen output. CE and Rohs listed. Dim-able using a variable voltage supply. Available in white 6000k and warm white 3000k. Great for vintage and classic vehicles, motorcycles and trucks. Up to a 600 Lumen output. The LED ae optically aligned to the original filament location. The lamp is dimmable using a variable voltage source. Since the lights are dim-able they operate better when there is a low voltage condition. If you are updating your bulbs that are in the turn signal circuit we recommend using 6 ohm load equalizer for each led in the turn signals or a led compatible flasher. The M.O.L. maximum overall length is 1.962" and the M.O.D. maximum overall diameter is 0.741". CE and Rohs.

1157 Led Bulb for 12 volt. Works for either positive ground or negative ground. BAY15D, indexed or offset bayonets, 15mm diameter base, two contacts on the bottom. Long life up to 30,000 hours. The led's are optically aligned with the reflector for maximum light output. Available in white 6000k, warm white 3000k, blue, green, red and yellow. This bulb is smaller than your incandescent bulb so you should not have any issues with installation. Comparable to a 27 watt to 37 watt halogen light bulb. Made with 5730 smd led's for high output lighting. Operates either 12v positive ground or 12v negative ground vehicles. The brake light is up to 500 Lumens. The tail light is up to 200 Lumens. The M.O.L. maximum overall length is 1.962" and the M.O.D. maximum overall diameter is 0.741". Dimmable with a variable voltage supply such as a dashboard dimmer switch.

BA15S LED Bulb works in positive or negative ground vehicles. Single filament lamp. Operates 12 volts non polarity. Super bright led lamp using the latest high power 3030 SMD led. Each 3030 SMD can emit up to 30 Lumen output. Up to 400 Lumen output. Up to 31 CP candle power. Super low profile to fit the small cowl lights, indicator, taillight. Viewing angle is 120 degrees. Comparable to a 25 to 30 watt halogen light bulb. Available in White 6000K, Warm White 3000K, Red 625 nm and Yellow Yellow 594 nm. Extremely long life up to 30,000 hours. Solid-state never have to worry about a broken filament with led lamps. Compatible with early vintage cars, trucks and motorcycles. Dimmable with a variable voltage supply such as your dashboard dimmer. Single Contact Bayonet where the bayonets are parallel to each other with one contact at the bottom. Compatible with the C6 Filament shape.

Operates 24 volts AC or 24 Volts DC. 8 qty 5050 LED's per Bulb, works either positive ground or negative ground, there is no polarity for this bulb. Up to 150 Lumen output forward firing. Up to 70 Lumen output. Uses up to 1.6 Watts. 360 Degree illumination or viewing angle. The base is BA15S single contact. The base is 15mm diameter. The bayonets are even. Operates only 24 Volts AC. White 6000K, Green, Blue, Red and Yellow. Long life up to 30,000 hours. This bulb is not dimmable. Comparable up to a 15 Watt to 20 Watt incandescent bulb. Starts to light around 12 Volts. The yellow color is polarity sensitive 24VDC and only works in negative ground. The maximum voltage is 28.5 volts. CE and Rohs.

Up to 2.6 Watt. Up to 350 Lumen output. Operates at 24 Volts AC. Since AC there is no polarity so the bulb can work in both positive ground and negative ground. Long life up to 30,000 hours. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow. BA15S base, bayonets are even, with single contact and 15mm diameter base.

1157 Bulb LED BAY15D Base 12 Volt 2.6 Watt. Works either positive ground or negative ground. Long life up to 30,000 hours. Up to 24 CP. Has dual filaments a brake light and tail light. Up to 320 Lumen for brake light and 240 Lumens for tail light. Dim-able with variable voltage supply. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow. One of the bayonets is offset. Comparable to a 20 to 25 Watt incandescent bulb. The approximate size is 1.47" long. The approximate diameter is 0.78". The BAY15D base is 15mm diameter, with offset bayonets and two contacts on the bottom. CE and Rohs. Compatible with: ge 2357f, 1964 Morgan Plus 4 Car

P15D-25-1 base. Dual filament, up to 950 Lumens per each filament. 12 Volt non polarity works either positive ground or negative ground. Uses 60 5730 smd leds. Up to 57 to 67 Watt incandescent equivalent. The leds are aligned with your reflector for maximum light output. Dim-able with a variable DC supply such as a dimmer switch. Available in white 6000K and warm white 3000k. Extended warranty, please see detail page for more information. Maximum overall length is 1.944 inches. The maximum diameter is 1.058" Compatible with: p15d-25-1 PX15d H6 h6m P15D

1158 LED Bulb BA15D Base 12 Volt 2.6 Watt G18. Operates either positive ground or negative ground. Taillight up to 240 Lumens, Brake light up to 320 Lumens. Available in White 6000K, Warm White 3000K, Red, Yellow, Green and Blue. Dim-able with variable voltage supply. The base bayonets are even with two contacts. The base diameter is 15mm. The MOL is 1.47", the MOD is .78". Long life up to 30,000 hours. CE and Rohs.

1142 Led Miniature Bulb 12v non polarity. Single filament. Up to 650 Lumen output. BA15D base has 2 bayonets the same height (even). The base is 15 mm diameter. The led's are optically aligned with the reflector for maximum light output. CE and Rohs listed. Up to 30,000 hours life. Comparable to a 35 to 45 Watt incandescent light bulb. Since this bulb is single filament means only its full bright and off. Works in both positive ground and negative ground 12 volt vehicles. Available in white 6000k, warm white 3000k, red, green, blue and yellow/amber. The maximum overall length MOL is 1.944 inches. The maximum diameter is .741 inches. Up to 500mA@12 Volt. Up to 6 LED Watts.

1156 led miniature bulb 12 volt. Operates non polarized positive or negative ground vehicles. Operates 12 volt. The base is BA15S, diameter 15mm, 2 bayonets same height and has one contact on the bottom. The leds are optically aligned for best light output through your reflector. Long life up to 30,000 hours. CE and Rohs listed. Available in white 6000k, warm white 3000k, yellow, red, green and blue. Very bright up to 950 Lumen output. Maximum overall length M.O.L. is 1.944 inches. The diameter is approximately 1.058"

Led Bulb BAY15D 12V LED Bulb. BAY15D base. Up to 900 Lumen output. Up to 700 Lumen for low beam. Long life up to 30,000 hours. CE and Rohs listed. The bulb is non polarity so you can use it either positive or negative ground vehicles, trucks and motorcycles. The led's are aligned so that the light output to the reflector is the most efficient. This bulb fits the outline of a standard light bulb so you should not have installation issues. Comparable to a 27 to 35 to 55 Watt halogen bulb. This bulb works great for sockets that are wired backwards. Available in warm white 3000k, white 6000k, red, green, yellow and blue. This is a 1157 or BAY15D which means that the bayonets are offset. The base diameter is 15mm. These lights led are super bright. Uses up to 1 Amp @ 6.3 Volts for high beam and up to .850 Amps for low beam. The maximum overall length M.O.L is 1.944". The maximum diameter is 1.05".

1142 Led Miniature Bulb. Up to 900 Lumen output. 12 Volt non polarity works either positive ground or negative ground. 60 quantity 5730 smd's. Comparable to a 50 to 60 Watt incandescent bulb. Long life up to 30,000 hours. The led's are optically aligned so that the maximum light output using your reflector. CE and Rohs listed. Single filament on full bright and off. The ba15d base is 15 mm diameter, 2 parallel bayonets and two contacts on the bottom. The color options are white 6000k, warm white 3000k, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. The led's are optically aligned with the reflector for maximum led light output. The bulb is dim-able using a variable voltage source such as your dashboard dimmer switch. Up to 300 Lumen for forward firing. Up to 400 Lumen for side firing. The maximum overall length M.O.L is 1.944". The maximum diameter is 1.05".

1156 Miniature LED Bulb. Operates 12v non polarity. Works either 12 volt positive ground or 12 volt negative ground. Up to 650 Lumen output. The bulb life up to 30,000 hours. Comparable 27 Watt to 37 Watt incandescent bulb. The leds are aligned to the reflector for best light output. Please see product page for warranty details. Available in white 6000k, warm white 3000k, green, blue red and yellow. Since the bulb is smaller than the original bulb there should be no issues installing the led light. This is a single filament bulb meaning just on and off. The base is 15mm diameter and the bayonets are the same height with a single contact on the bottom. Compatible with: Ryobi and Husqvarna Lawn Tractors and Mowers Husqvarna 532004152

194 Wedge Concave LED Light. 1 LED. Durable, shock and vibration proof, instant On/Off. 0.27 Wattage equivalent. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 12 VDC. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W.

LED T10 Wedge 13 5050 (3 Chip) LED LIght. 12 volt D.C. This led light has 13 5050 SMT leds. Very bright around .18 Watt of power.

18 1210 SMT T10 Wedge LED Light Bulb. This L.E.D. Light has 15 side firing and 3 forward firing 1210 S.M.T. LEDs. Uses 3 watts of power at 12.5VDC. White 6000K. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in white only. Approximate size is 1.44in x .40in. Approx. 180 Lumens.

194 Miniature Wedge LED Bulb Short Round. Up to 7 Lumen output. Long life up to 30,000 hours. Comparable to a 4 to 9 Watt halogen lamp. Has 1 LED. very durable. Since the bulb is solid state the color is monochromatic. low heat generation, virtually unbreakable. Available in super white 6000K, red 625nm, yellow 594nm, green 526nm and blue 464nm. 6 to 12 VDC. Bulb size is T3 1/3 or T3.25 known as the T10 Wedge. The bulb fits dashboard, glove box, door, hood, dome, license plate and many other uses. Viewing angle 60 degrees. Self ballasted with a resistor. Rated voltage from 6V to 15V DC. Uses only 10 Ma @ 12V DC. Designed for negative ground cars, trucks and motorcycles. High quality with warranty, please see bottom of detail page. Fits a standard T10 miniature wedge. Dim-able with a dashboard dimming knob. Comparable to a glass wedge W2.1x9.5d.

194 LED Bulb 5 SMD. Up to 50 Lumen output forward firing. Up to 40 Lumen side firing. Long life up to 30,000 hours. Solid state so the bulb is durable, shock and vibration proof. Since the lamp is solid state the light is instant On. Measures .064 diameter by 1.097" overall length. Available in super white 6000K, Daylight White 4400K, Warm White 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. The current use is 20 mA @ 13.8V DC., 1.5 Watts@13.8 VDC. Comparable to a 15 Watt incandescent bulb. Fits T10 wedge or miniature wedge. Called T3 1/4 or T3.25. The bulb is dim-able using a variable DC power source such as a dashboard dimmer control. The bulb is polarity sensitive DC, which means you have to insert the bulb and if it does not work re-insert the bulb 180 degree and it will illuminate. Each smd chip is 120 degrees viewing angle the whole bulb is 360-degree viewing angle.

194 LED Bulb 1 Watt High Power LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Up to a 80 Lumen output. Available in super white. 1W @ 13.8 VDC. White 6000K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). Works great for dome, map, door lights, trunk and hood lights, turn signals, dashboard, gauges and so on so many uses. Save power and time replacing incandescent light bulb with a led light. Comparable to a 8 to 10 watt incandescent light bulb. CE and Rohs listed. 120 Degree viewing angle. The LED is ballasted by a resistor that allows the voltage from 8 volts up to 17 volts DC. The operating voltage is 13.8V DC. The bulb works in negative ground chassis. The ballast is a resistor. The bulb is dim-able by a voltage source that varies in voltage such a the dashboard dimmer switch.

194 LED Bulb T10 Wedge, up to 240 Lumens, 3 watts, 360 degree illumination. 100% error free can bus. 12V DC, long life up to 25,000 hours. Nice heat sink to keep the led's cooler so they last longer. White 6000K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). 25-watt equivalent. This bulb is dim-able using a variable DC power source such as your dimmer know in your automobile dashboard. Can bus compatible, long life up to 25, 000 hours. Approximate size .986" long by .459' diameter. Each chip viewing degree is 120 degrees while the whole bulb is 360-degree illumination. Fits T10 female wedge socket. The bulb shape is T3 1/4. This bulb is dim-able using a variable DC power source such as a dimmer knob on your dashboard. The led bulb is polarity sensitive only operates using DC. This bulb works from 9V to 17V with the ideal voltage 12V DC.

T10 CAN Bus, new 4014 SMD, very bright, 24 LED's, viewing angle 180 degree, 12 Volt A.C. or 12 volt D.C., CE, Rohs listed, Long life up to 30,000 hours, available in white 6000K and warm white 3000k The 4014 SMD L.E.D is a very good shape for high output led lighting for cars, automobiles, motor cycles. Long life up to 30,000 hours. 120 degree viewing angle. Light shines from both sides. Very bright. Up to 300 Lumens. Dim-able with a variable voltage such as your dashboard dimmer. Comparable to a 15 to 20 Watt incandescent.

Up to 250 Lumen output. Available in super white 6000K, warm white 3000K, red, yellow, green and blue. 240 mA @ 12V DC. Size is 2.27 inches tip to bottom and the diameter is 0.51 inches. High tech heat sink to make the LED Light last longer. Dim-able with a dashboard dimming knob that varies the voltage. CE and Rohs certified. Comparable to 20 to 25 Watt incandescent light bulb. Long life up to 30,000 hours. The bulb operates from 8V to 16V being self ballasted. The ballast is a resistor. The led lamp is designed continues use for RV and marine applications. This bulb works good in cars, trucks, tractors, motorcycles and scooters. The led bulb is designed to operate negative ground chassis. The led is comparable to a glass wedge W2.1x9.5d light bulb.

T10 L.E.D. CAN Bus, 12 Volt D.C., 360 degree viewing, long life up to 30,000 hours, CE, Rohs listed, Available in white 6000k and warm white 3000k.

T10 Wedge 25 Ultra Bright SMT LED Light. 25 SMT LEDs. Durable, shock and vibration proof, instant On/Off. Measures .47in wide and 1.50in from top to bottom. 80 lumens side firing. 25 lumens forward firing. Available in super white. .110A@13.8 VDC. 1.5 Watts@13.8 VDC.

194 LED Bulb 3 Watt forward firing + 2 Watt side firing, with lens and 4 5630 side firing led's. Very bright in 360 degrees. 12 Volt D.C. Available in white 6000K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). T10 Wedge base. Up to 350 Lumen output, equivalent to a 30 watt incandescent bulb. Comparable to a 25 to 30 Watt incandescent light bulb. Long life up to 30,000 hours. CE and Rohs certified. Dim-able with a dashboard dimming knob. Very bright works good in led turn signals, dome light, glove box, dashboard, instrument panel. This led bulb is comparable to a standard glass wedge W2.1x9.5d. Since this led lamp operates 12 Volt AC or 12 Volt DC positive ground or negative ground. 360 degree viewing angle. This led lamp is very bright and emits light in 360 degree illumination.

194 Wedge 6 Ultra Bright Side Firing LED Light. 6 Ultra Bright SMT LEDs. Durable, shock and vibration proof, instant On/Off. Works 12 Volts non polarity. If this bulb does not light the desired spot you can rotate 180 degrees and the bulb will still work. 12V AC. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. This product measures approximately 1.11 inches by 0.40 inches by 0.27 inches. 100 lumens. Please see product detail for warranty period.

Very bright T10 Wedge LED Light, 3 Watt, clear lens, 12V DC. Long lasting, low power, save time and money by replacing incandescent lamp with T10 LED lamp. Comparable to a 20 watt light bulb. Approximately 265 lumens. White 6000 K, Warm White 3000 K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. This bulb is dimmable using a variable DC source. The body style is T3 1/4 or T3.25 fits a standard T10 Wedge female socket. The bulb is polarity sensitive meaning it works on DC. Overall size .995" length by .391" diameter. The current at 12V DC is .079A. Drop in replacement for glass wedge incandescent bulbs. Compatible with: #147 #152 #158 #159 #161 #168 #184 #192 #193 #194 #259 #280 #285 #447 #464 #555 #558 #585 #655 #656 #657 #1250 #1251 #1252 #2450 #2652 #2921 #2825 #12256 #12961 #2521 #2525 W5W

T10 Wedge 8 1210 SMD Forward Firing LEDs. 8 SMD LEDs that are forward firing. Available in white only. 12 VDC. Approximate size is .68in x .46in. Dimmable with a variable voltage supply such as your dashboard dimmer switch. Up to 60 Lumen output. 120 degree viewing angle. CE and Rohs.

9 LED T10 Wedge. Nine LEDs in a T10 Package. Use this 194 9 LED for dashboards, inside illumination and other LED applications. Available in white only. Approximate size is .85in x .45in. Puts out approximately 40 lumens.

120 Lumen output, 240 mA current @ 12 VDC. 2.69 Watt input consumption, 25 Watt equivalent output. 6000-6500 Kelvin White or 3000-3500 Kelvin Warm White. 10,000 hour life. Operating voltage 12V VDC. Roughly 1.78 inches in length and .9 x .9inches. High tech heat sink to make the LED Light last longer. Designed for automotive, RV and marine uses along with many others. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W.

T10 wedge, 8 SMD 5730 chips, uses up to 4 watts of power, Up to 400 lumen output. Operates at 12 volt dc. Long life up to 30,000 hours. Has CAN Bus error free communications. CE and Rohs listed. Available in white 6000K, red, blue, green and yellow/amber. 360 degree viewing angle. Comparable to a 30 to 40 Watt incandescent bulb.

T10 wedge has 9 3528 led's. 3 Led's are forward firing and 6 leds are side firing. Wide voltage range from 12-24 Volt A.C. or D.C.. Error free CAN Bus for talking to vehicle computer system. Available in white 6000K. Long life up to 30,000 hours. CE and Rohs listed. Dim-able with a variable voltage supply such as your dashboard dimmer switch. Comparable to a 4 to 9 Watt Incandescent bulb.

T10 Wedge 12 SMD 5730 CAN Bus 4 Watt, up to 400 lumen output, extremely bright. Operates 12 Volt DC negative ground. Uses 12 5730 high power chip. Long life up to 30,000 hours, available in white 6000k, warm white 3000k and colors. The 5730 surface mountable device dissipates 1/2 watt of power and emits around 40-50 lumen output. The LED SMD chip works very good for automotive, motorcycle and boating applications. Up to 240 degree viewing angle. CE and Rohs. Comparable to a 36 Watt incandescent bulb. Dimmable with variable voltage supply such as your dashboard dimmer switch.

194 LED Bulb 9 5050 2.5 Watt T10 Wedge 12V, Pure White 6000K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm) & Yellow(594nm). Long life up to 30,000 hours. Ultra bright up to 135 lumen output. 360 degree illumination. Great for dome light, map light, turn signal light, dashboard light and door lights. Dim-able using a dashboard dimmer. Comparable to a 25 to 20 Watt incandescent light bulb. Single filament. This led can be used as a replacement for glass wedge base miniature bulbs. The led plastic wedge base bulb shape is compatible with #194B #194R #194G #194Y #194 T10 T-10 #147 #152 #158 #159 #161 #168 #184 #192 #193 #194 #194 #259 #280 #285 #447 #464 #555 #558 #585 #655 #656 #657 #1250 #1251 #1252 #2450 #2652 #2921 #2825 #12256 #12961 #2521 #2525 W5W

194 Wedge 4 LED Light. 4 LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 12 VDC. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W.

T10 Wedge using high power 7060 SMD. 12 Volt operation, 180 degree viewing, CANBus error free, CE and Rohs listed, long life up to 30,000 hours, up to 125 lumen output. Available in warm white 3000k and white 6000K. Works great for vehicles that give the warring that the can bus bulb is out, this led bulb will save power and last longer than a original replacement.

T10 Wedge Can bus, up to 300 lumen, 3 watt, Up to 300 Lumens, 25-30 watt incandescent equivalent. long life up to 30,000 hours, available in White 6000K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). 120 degree viewing angle. 100% error free can bus operation. Works either positive ground or negative ground. CE and Rohs.

194 Super Flux Side Firing LED Light. 18 Side firing super flux LED chips. Each super flux LED has 3 LED chips. Approximate size is 1.85in x .62in. Available in super white, red, yellow and blue. Uses .14 mA @ 13.8 VDC. This product is polarity insensitive. 1.7 Watts, Equivalent to a 12 watt incandescent. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W. Works either AC or DC. Dim-able with a variable voltage such as your dashboard dimmer.

T10 Wedge 12 SMD 2835, Very bright up to 250 lumen output for 2.5 watts. CANBUS error free, Long life up to 30,000 hours, Available in white and warm white and all colors.

T10 Wedge, Wide voltage AC or DC 9-32V. Up to 280 lumen output. 25 degree viewing angle. Very small profile, great for dashboards, tail lights, stop lights, also can be used as a T15 third brake light. CE ROHS listed. CRI>=80 white 6000 kelvin color. Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). Comes 1 per package.

T10 Super Flux Custom 6 LED Light 12 VAC. 194 Super Flux Custom LED Light. 6 super flux LED chips. Each super flux LED has 3 LED chips. Approximate size is 1.46in x .63in x .60in. Available in super white, red, yellow and blue. Uses only .16 mA @ 13.8 VAC. 500 Lumens Forward Firing, 25 Lumens Side Firing. This product is polarity insensitive. Dim-able with variable voltage supply. The light assembly can be custom placed. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W.

T10 wedge with 10 SMD LEDs. Up to 5 Watts. Up to 350 Lumns. Each SMD outputs up to 1/2 Watt. Very bright. 1.23" in total length and .46" wide. Available in white 6000K, warm white 3000K, red, green, blue and yellow. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W. Operates DC 12 volt. Long life up to 30,000 hours. Comparable to 45 Watt incandescent bulb. CE and Rohs listed. 360 degree viewing angle.

Output up to 90 lumen output. T10 Wedge 1 Watt COB High Lumen 12VDC White. One per package. Uses 12VDC, 40mA. 120 degree beam angle.. Approx. 0.46" x 0.68" Base ~ 0.36". CE & RoHS certified. White 6000K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm).

194 Wedge 3 LED Light. 3 LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 29mA@13.8 VDC 400mW. 20 Lux@1ft, 4lux@1ft side firing. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W.

194 Wedge Super Flux LED Light. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green, blue and ultra violet. 800mW@13.8 VDC. Approximate size is 1.12 inches in length and .4 inches in diameter. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W. Dimmable with a variable voltage supply. Viewing angle 120 degrees. Comparable to a 4 to 9 Watt incandscent bulb. Long life up to 30,000 hours.

1 SMT 5050 (3 Chip). Low profile SMT LED Lamp. 12 VDC. Available only in white. This LED measures from top to bottom .70in and a width of .44in. Very bright. Uses 3 L.E.D. chips per 5050 LED. Up to 16 lumen output.

1895 LED Bulb has 24 Super Flux T10 Wedge BA9S 36 mm Festoon LED Light Bulb. This bulb uses 24 super flux LEDs. The color is white approximate 5500-6500 Kelvin. Low voltage 12 VDC. Has T10 Wedge, BA9S and 36 mm Festoon. Has 3m double sided tape so you can stick this led light almost anywhere. This led measures 2.30 inches by 0.96 inches. Dim-able with a dashboard dimmer switch. Comparable to a 10 to 15 Watt incandescent light bulb. Compatible with 1953 Cessna 170 ba9s light bulbs.

194 Wedge Flat LED Light. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green, blue and violet. Approximately 7 lumens output. 12 VDC. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W.

194 Wedge 6 LED Light. 6 LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic pure color, low heat generation, virtually unbreakable. Available in super white 5500 Kelvin to 6500 Kelvin, red, yellow, green and blue. 12 VDC. 1" length and 4/10" diameter. Uses 40 mA @ 13.8 VDC = .552 Watts. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W. Output up to 40 lumen output. This led bulb has a 30 degree viewing angle. This bulb will dim by using a variable voltage. The bulb is polarity sensitive, meaning if it does not illuminate when you install it, please rotate the led bulb 180 degrees and reinstall the led bulb.

1.5 Watt T10 wedge with concave lens. Up to 110 Lumen output. This T10 wedge has a lens to provide led light in 120 degrees. This is a very bright in all directions that are forward firing. 12 Volt DC for negative ground vehicles. Available in white only. Approximate size is 1.12in x .46in. Comparable to 15 Watt incandescent bulb. Dim-able with a variable voltage supply such as your dashboard dimmer switch. Dimmable from voltage 7.12 Volts to 13.8 Volts. 120 degree viewing angle. Long life up to 30,000 hours. Available in White 5500-6500K. CE and Rohs.

194 Wedge Tall Round LED Light. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue and gradual changing RGB. 12 VDC. 25mA @12.8VDC. Uses .32 watts. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W.

T10-Wedge 5050 3 Chip LED Light Bulb for BMW, Audi, Benz. Use this T10 wedge for european cars the have a smart network to eliminate the bulb out status. Available in white only. 12 Volts DC. Uses the CAN-Bus network. This led measures approximately 0.84 inches by 0.35 inches. Replaces BMW Audi Benz. The l.e.d. bulb is comparable to a 10 Watt incandescent light bulb.

194 Wedge Super Flux LED Light. 9 super flux LEDs. Up to 100 Lumen output. Dimmable with a variable voltage supply. Durable, shock and vibration proof, instant On/Off. 360 degree viewing angle. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow and blue. Comparable to a 9 to 10 Watt incandescent bulb. Uses approximately 900mW @ 13.8 VDC. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W. Compatible with Mercedes 981-84 Diesel 300d chassis W123

194 Wedge 4 Ultra Bright Side Firing LED Light. 4 Ultra Bright SMT LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. This LED measures approximately 1.06 inches by 0.39 inches by 0.23 inches. Available in super white, red, yellow, green and blue. Works either positive ground or negative ground. Since the bulb is 12 Volt AC the LED's will work both ways inserted into a socket. Comparable to a 9 to 16 Watt incandescent bulb. 120 degree viewing angle.

7 LED T10 Wedge LED Light. 12 VDC. 7 T1 LEDs. Very bright. Available in white. Approximate size is .88in (height) x .44in (diameter).

1/2 Watt L.E.D.High Power. 1/2 Watt high power LED. T10 base. 12 VDC. Available in white. This LED measures from top to bottom .90in and a width of .47in.

9 SMT 5050 (3 chip) T10 Wedge LED Light. Available in white only. 12 VDC. This LED measures from top to bottom 1.40in and a width of .40in. Has 27 total L.E.D. chips inside of 9 5050 SMT LEDs. Up to 70 Lumen forward firing and 60 Lumen side firing

194 Wedge 4 Ultra Bright 4 SMD Forward Firing LED Light. 4 SMD LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Approximate size is .71in (height) x .44in (diameter). Available in super white, red, yellow, green and blue. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W. Save your power usage·Unique and attractive color light·Easy installation, just plug& play ·For use in your vehicle's:Dashboard lights, Interior lights, Side lights, License plate light. Uses .56 watts, Comparable to a 5 watt incandescent light bulb. Up to 36 Lumen output. This bulb is comparable to a 4 to 9 Watt incandescent bulb.

1 Watt High power LED forward firing, plus 3 LEDs side firing T10 wedge. 12 VDC. Available in white only. Excellent product for side markers. Approximate size is .98in (height) x .46in (diameter).

194 Wedge 5 LED Light. 5 LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 12 VDC. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W.

194 Wedge SMT 11 LED Light. 11 SMT LEDs. 3 forward firing and 8 side firing LEDs. Available colors for this product are super white, red, amber yellow, green and blue. Durable, shock and vibration proof, instant On/Off. Available in super white. .09 mA @ 13.8 VDC. 1.5 Watts@13.8 VDC. Approximate size is 1.15in x .44in.

T10 Wedge 2 SMD 5630 (3 Chip) Round Lens 12VDC. Use this weather resistant LED bulb for applications that need some protection from harsh enviroments. 12V DC, White 6000K, Long life up to 30, 000 hours. About 1" long and .44" wide. The plastic lens is around .25".

E10 Screw (T10) Concave LED Light. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green, blue and rgb. .02 mA@13.8VDC 345mW. Approximate size is .90in x .39in 10mm (height x diameter). Operates from 6 to 12 volts DC. Up to 7 Lumen output. The viewing angle is 60 degrees.

LED 4 Watt T10 Wedge 12 Volt DC. This T10 Wedge has 6 .65 Watt LED Lights. Available in white 5500K-6500K. This LED measures approximately 1.45 inches by 0.47 inches. 30 watt incandescent equivalent.

159 led Bulb for 6 volt Negative Chassis 159 T10 wedge. Great for old vehicles that were built or constructed before world war II. These older vehicles and motorcycles have a 6v negative chassis. This T10 miniature bulb glass wedge will work in these old classic, vintage cars. The T10 rated voltage is 6 volts. Up to 30 Lumen side firing and 70 Lumen forward firing. Up to 1 Watt at 6 volts. Comparable to a 8 to 10 watt incandescent bulb. This led bulb fits arcade games, pinball machines and amusement rides that require 6 volt DC mini T10 wedge. This bulb also replaces 6.3V or 6V. This led bulb is a great replacement for glass wedge incandescent bulb. This bulb is T3-1/4, T3.25 shape meaning tubular and 3-1/4 wide. CE and Rohs listed. Dim-able using a variable voltage supply such as the dashboard dimmer. Great for dome, glove box, dashboard, panel, license plate and other accessory lighting.

Short Round T10 Wedge LED Bulb. Available in white only. 12 Volt D.C. T10 Wedge. Great for instrument panels, ashtray lights and other lights in the interior of the automobile. Long life and low current.

12929 Miniature LED Bulb LED Panel 24 SMD 5050 T10 BA9S 36mm. Low Voltage 12 volt direct current. Has 24 super bright 5050 SMD LEDs. Has 3 adapters T10 wedge, BA9S and 36 mm festoon. This product has an adhesive back for easy mounting and installation. This product measures 2.58 inches by 1.74 inches. Available in White 6000K only. That is the correct dimensions, the video dimensions are stated incorrectly. Dim-able with a dashboard dimmer switch. Up to 300 Lumen output. 120 degree viewing angle. Comparable to 25 to 35 Watt incandescent light bulb. Compatible with 1953 Cessna 170 ba9s light bulbs. Uses up to 4 watts. Uses current up to 12 Volts@.40A.

194 Wedge 3 Ultra Bright 3 SMT Forward Firing LED Light. 3 SMT LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. This LED light bulb measures .87" from top to bottom and .43" diameter. Dim-able with a variable voltage supply. 120 degree viewing angle. Comparable to a 4-9 Watt incandescent bulb. CE and Rohs.

1/2 Watt High Power LED Light. 1 LED. .08 mA@13.8 VDC. Available in super white, red, green, blue and yellow amber. Durable, shock and vibration proof, instant On/Off. 5 watt incandescent equivalent. Approximately 40 lumens. Monochromatic (pure) color, low heat generation, virtually unbreakable. Approximate size is 1.06in x .43in. Perfect for all applications calling for a T10 size bulb including, boats, RVs, cars ect. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W.

3 SMD 3528 LEDs T10 Wedge. Twelve volts direct current. Available in white only. 3 3528 SMD L.E.D.'s. Approximate size .73in (height) x .44in (diameter).

1 1/2 Watt High Power LED T10 Wedge. Very bright 12 VDC LED. Available in white only. Great for illumination of dashboards and instrument panels. Approximately up to 15 watt output foward firing size is 1in (height) x .47in (diameter).

4 5050 SMD Forward Firing T10 Wedge LED Lamp. 12 VDC. Available in white. Uses 4 5050 SMD LEDs to shoot all the LED Light in a forward direction to maximize the lighting effect. Approximate size is .75in (height) x .56in (width). The Lumen is up to 52. Comparable to a 4 to 9 Watt incandescent bulb. Extremely low profile for tight 194 locations.

194 (T10) Wedge 12 SMT Side Firing LED Light. 120 lumens 240 mA. Has polarity diodes for AC/DC operation. 120 Lumen output, 240 mA current @ 12 VDC. 3.726 Watt input consumption, 25 Watt equivalent output. 5500 Kelvin Super White or 3000 Kelvin Warm White. 10,000 hour life. Operating voltage 12V VDC. Roughly 1.91 inches in length and .9 x .9inches. High tech heat sink to make the LED Light last longer. Designed for automotive, RV and marine uses along with many others. Replaces 194 T10 T-10 147 152 158 159 161 168 184 192 193 194 #194 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 12256 12961 2521 2525 W5W.

6 SMD 1201 L.E.D. 3 Forward/ 3 Side T10 Wedge Light. 12 VDC. Available in white. This T10 directs the light in all directions so you get both side firing and forward firing led light. This LED measures from top to bottom .88in with a diameter of .45in.

Super bright 12 One Watt LED's 12 Volt DC. Works only negative ground vehicles. Can use BA9S or T10 Wedge or 36mm Festoon. Available in White 6000K. Up to 1200 Lumen output. 120 Degree viewing angle. Dimmable with a variable voltage supply. Has double sided sticky tape on the back side. CE and Rohs.

159 LED Bulb works 6 volt positive or Negative Ground 159 T10 wedge. Great for old vehicles that were built or constructed before world war II. These older vehicles and motorcycles have a 6v positive chassis or 6v negative chassis. This T10 miniature bulb glass wedge will work in these old classic, vintage cars. The T10 rated voltage is 6 volts. Up to 30 Lumen side firing and 70 Lumen forward firing or 5.5 CP candle power for forward firing and 3.3 CP for side firing. Up to 1 Watt at 6 volts. Comparable to a 8 to 10 watt incandescent bulb. This led bulb fits arcade games, pinball machines and amusement rides that require 6 volt ac mini T10 wedge. This bulb also replaces 6V, 6.3V or 6.8V. Since this bulb is non polarity it can be used in 6 volt landscape lighting. This led bulb is a great replacement for glass wedge incandescent bulb. This bulb is T3-1/4, T3.25 shape meaning tubular and 3-1/4 wide.

Use one load equalizer for each led bulb in your turn signal circuit. Since this heavy duty load equalizer runs cooler it last longer. Stops hyper flashing and fixes CAN bus errors. Operates 6 Volt or 12 Volt positive ground or negative ground. The wire is 14 AWG high temperature. Comes with two insulation displacement connectors "IDC". Please do not cut your vehicle or motorcycle wires, just crimp the IDC on to your existing wires so that the load equalizers are in parallel with the led bulbs. The resistor body material is made from anodize aluminum. The rated current is up to 4 Amps. Since the load equalizer is 50 Watt power dissipation it runs cooler. The led light equalizer will get hot to the touch so it is recommended to mount to a metal surface. The body has mounting holes so you can easily attach it to a metal surface. The operating temp is around 100 degrees Celsius.

Use only two 3 Ohm 50 Watt Load Equalizers for your vehicle for the left and right side. Stops led light hyper-flashing and fixes CAN bus errors. Operates 6 Volt or 12 Volt positive ground or negative ground. The load equalizer can handle up to 4 Amps either 6 Volt or 12 Volt positive ground or negative ground. Since the resistor body is larger it runs cooler so load equalizer will last longer. The wire is 18 AWG high temperature resistant wires. Comes with two insulation displacement connectors so you can crimp these on to your existing wiring. Please install in parallel and do you cut your vehicle wires. Since the 3 Ohm 50 Watt is designed to install on the left or right side you only use two load equalizers instead of four. The load equalizer body is made of anodized aluminum. Please make sure to mount to metal surface since the body of the load equalizer gets hot.

Fixes flashing headlights or headlights that will not change from low beam to high beam. Operates 6 Volt or 12 Volt positive ground or negative ground. This heavy duty led headlight load equalizer operates cooler so it last longer. Rated at 4 Amps. Body is anodized aluminum. Comes with two insulation displacement connectors "IDC". Please crimp on to your existing wiring in parallel with the low beam on both your headlights. No need to cut your wiring harnesses when using the insulation displacement crimps. To test once installed the load equalizer should get warm or hot to the touch when you headlights on are low beam. The load equalizers come with 14 AWG heat resistant wiring. Please mount to a metal surface to help the load equalizer stay cooler. No need to purchase expensive and complicated harnesses when using these load equalizers. The wire length is about 4.5".

LED Compatible flasher. The LED compatible flasher is for 7 to 24 Volts DC. Maximum voltage 31 volts. Negative ground vehicles or motorcycles. This 2 prong round flasher can handle up to 150 Watts of led or incandescence bulbs. 1 to 6 LED Bulbs or incandescent bulbs. Each incandescent bulb is around 21 Watts. The flasher will flash between 60 and 120 Hz. The flasher can power from 0.1 Watt to 150 Watts of lighting, .02A-20A. Operating Voltage from 7 Volts DC to 31 Volts DC. The duty ratio of this flasher can range from 30% to 70%. The operating temperature from -40C to +80C. The flashers life time is up to 400 hours of flashing time. The flashers body is round. Plug and play disconnect power remove old flasher and install new flasher reconnect power. Very easy to eliminate hyper flashing by replacing your old flasher with this LED compatible flasher.

Converts your 6 Volt vehicle to be able to power 12 Volt accessories. Powers anything that is 4 Amps @ 12 Volt. The ballast has enough power in a small size. The input is 8 Amps @ 6 Volt input and the output is 4 amps @ 12 Volt. Works on both 6 Volt negative ground and 6 Volt positive ground cars, trucks, tractors and motorcycles. Long warranty please set page details for further warranty information. Easy to connect for (DIY) do it yourself retrofit. The ballast is water proof and is a non-isolated design. Please connect the ground and input 6 volt signal to the input side of the ballast the red and black wires. Please connect the output to a 12 Volt device using the yellow and black wires. With this ballast you can have DVD, Bluetooth, WIFI, USB port in your vintage and classic vehicles designed and built before World War II.

17" LED Third brake light for antique vehicles has dual filament. DOT lens. Available in Red and Yellow/Amber. This third brake light is for 6 volt vintage and classic vehicles, cars, trucks and motorcycles. Uses approximately up to 720mA@6.8 Volts for the brake light and uses up to 88mA@6.8 Volts for taillight. The brake light is up to 4.9 watts @ 6.8 Volts for brake light and the tail light is up to .59 Watts. Comparable up to a 40 to 45 Watt incandescent bulb. This third brake light will work either positive ground or negative ground. Operates from 3.2 Volts to 7.8 Volts non polarity. Works with either positive ground or negative ground. Has two recessed mounting holes that are .165" diameter so you can mount this on the surface. The hole to hole spacing is 16.14". If mounting to glass you would need to use some double sided tape or fabricate some kind of mounting bracket to use on glass.

1154 led bulb for 6 Volt. The led bulb works for both positive ground chassis or negative ground chassis. 1154 LED bulb is a 6v led bulb. Up to 320 Lumen for brake light and up to 240 Lumen for tail light. This bulb is same as 1154 bulb that has two brightness levels or two filaments one is for the tail light and the other is for the brake light. This bulb works great for non polarity 6 volt positive or negative ground. The LED bulb is small in size so it fits in G18 and S8/S25 bulb size applications. Made with the highest quality Samsung 5730 SMD led chips. Operates voltage up to 7.4 Volts. Voltage higher than 7.8 Volts will damage this bulb and voids warranty. The white 6000K bulb starts to light at at 3.5 Volts. This bulb will work the same as a incandescent bulb without the power drain or the filament breaking. Uses about 290mA @ 6.8 Volt for brake light and 90mA @ 6.8 Volt for taillight.

1158 LED Bulb operates in Positive Chassis ground or Negative Chassis ground vehicles, trucks and motorcycles. Special design for older cars. 1158 with a BA15D Bayonet base and has two brightness levels. The life is up to 30,000 hours. Available in white 6000 Kelvin, warm white 3000 Kelvin, Red 625 nm Green 526 nm, Blue 464 nm& Yellow 594 nm. Available 1158 BA15D. Great bulb for tight fit, this small high power led is great for all applications, very bright 320 lumen or 25 CP Candle Power output for brake light and 260 Lumen or 20 CP Candle Power for taillight. The lamp illuminates in 360 degrees. This bulb will operate in classic old cars with positive chassis or negative chassis car or bike, low voltage. Comparable to a 25 watt incandescent, very small fits it tight bulb locations. CE and Rohs listed. Works good for navigation lights for its small profile, operates both AC or DC.

Headlight bulb 6 Volt Positive Ground or 6 Volt Negative Ground. 6V AC or DC. Up to 650 Lumen high beam and up to 510 Lumen for low beam. This headlight bulb is up to 50 candle power CP for high beam. Up to 40 candle power CP for low beam. Dual filament design. Designed for reflector headlights since most of the leds are side firing directly into the reflector. The bulb has some forward firing leds to make it brighter. This LED bulb is designed for early vintage Ford Model T headlight and Ford Model A headlight. Long life up to 30,000 hours. Plug and play remove the old incandescent bulb and replace with LED bulb. The LED uses less power than a incandescent bulb so it is easier on the wiring of the older vehicles. This headlight bulb uses approximately .112 Amp @ 6.9 volts for low beam. This led headlamp bulb uses around .490 amp @ 6.9 volts for hi beam. The bulb comes in White 6000K and Warm white 3000K.

1129 led bulb will operate in both positive ground or negative ground 6 to 12 volt systems. Up to 24 CP regardless of voltage from 6 to 12. Up to 330 Lumen output. G18 S25 2.6 Watt bulb. Has 6 forward firing and 7 side firing LEDs. Each 5730 SMD LED is capable up to 1/2 Watt of power. Each 5730 LED can output up to 50 Lumens. The LED is not powered to full power so it can operate cooler so the SMD will last longer. The life is up to 30,000 hours. Since this led light bulb has 360 degree viewing angle up to 320 Lumen output for forward firing. Up to 350 Lumen output for side firing. Available in white 6000 Kelvin, warm white 3000 Kelvin, Red 625 nm Green 526 nm, Blue 464 nm& Yellow 594 nm. Available 1156 BA15S. Great bulb for tight fit, this small high power led is great for all applications. Will operate in classic old vintage antique cars positive earth, trucks or motorcycles 6 volt low voltage.

E10 Screw Bulb Led Short Round 6V to 12V DC. Virtually unbreakable, reliable performance. Available in super white, red, yellow, green, blue and rgb. 120 degree viewing angle. Uses only 20mA@13.8 Volts DC. Approximate size is .92in x .39in 10 mm(height x diameter). Fits T3 1/4, T3.25 size bulbs. E10 Miniature Screw Base. Short Round LED Light. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, . 6V to 12v DC. This LED lamp has built in ballast that allows the LED bulb to operate from 6V to 15V. Comparable to a 4 to 9 Watt incandescent led bulb. The bulbs works in negative ground or negative chassis cars, trucks, motorcycles, tractors and scooters. Up to 7 Lumen output. Long lasting life up to 30,000 hours. Mini indicator LED lamp. Dim-able using a dashboard dimmer knob.

1142 LED Miniature BA15D S8 shape. Operates positive chassis or negative chassis 6 to 12 Volts. BA15D DC Bayonet 2.6 Watt L.E.D. bulb. Has 6 forward firing and 7 side firing LED's. Up to 30 CP. The LED bulb has a single filament brightness. This bulb will operate in a non polarity 6 volt systems positive chassis or negative chassis. The life is up to 30,000 hours. Available in white 6000 Kelvin, warm white 3000 Kelvin, Red 625 nm Green 526 nm, Blue 464 nm& Yellow 594 nm. Available BA15D. Please see 78865 for BA15S or 1156. Great bulb for tight fit, this small high power led is great for all applications, very bright 260 Lumen output in 360 degree illumination. This bulb will operate in vintage and classic old cars with positive grounds or positive chassis car or bike, low voltage. Comparable to a 20 watt incandescent, very small fits it tight bulb locations. CE and Rohs listed.

6V AC or DC. Use in positive ground or negative ground. 18 forward firing LEDs and 6 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat, virtually unbreakable. Up to 16 CP candle power output. Available in super white, red, yellow, green and blue. 6 VDC/ VAC. Approximate size is 1.57in x 1.03in. The max voltage is 8 volts. This 6 Volt bulb is designed for vintage vehicles and motorcycles for both negative ground chassis from post World War II and positive chassis from pre World War II. This product works when you apply 0 to the base and 6 Volts to the tip or if you apply 6 Volt to the base and ground to the tip the LED will light. This product will work both 6 Volt A.C. and 6 Volt D.C/A.C. applications. 1156 & 1157 bases. BA15S or BAY15d. Uses 1.8 watts, 15 watt incandescent equivalent, Up to 200 Lumen output.

Small E5 Midget 1 L.E.D., Available in 6VDC, 12VDC and 24VDC options. Up to 7 Lumen output, long life up to 50,000 hours. Available in Warm White 3000K and White 6000K. Uses very low .1 W power, uses 20ma@6V, 13ma@12v. The viewing angle is 90 degrees. MINIATURE T1 3/4 MIDGET SCREW (E5) BASE BULB. Comparable to a 4 Watt incandescent bulb. CRI>75. The miniature led lamp is called E5 since the base is 5 mm in diameter. This bulb is real small for E5 female screw base socket or lamp holder. The bulb operates at 6 Volt, 12 Volt and 24 Volts. This led bulb works great for back lighting for the ignition switch and various other areas of the dashboard compatible with Rolls Royce cars. This bulb is compatible with #272-1143, 272-1143, #8362, #335, #373, #342, #399, #1768, #1775, 176769L, #7326, #1769 These are tiny led light bulbs. The lamp will turn on around 2.5 Volts and gets brighter up to 6 Volts.

18 forward firing LEDs and 6 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat, virtually unbreakable. Available in super white, red, yellow, green and blue. 6 VDC. Approximate size is 1.57in x 1.03in. This 6 Volt bulb is designed for negative ground chassis from post world war II. The center contact is Plus 6 Volts and the bayonet body is negative or zero volts ground. This bulb will not work in most pre world war II 6 Volt cars except for Model T Fords from 1909 to 1927 are negative ground. Please see part number 95634 to operate in both pre and post World War II vehicles. Equivalent to a 15 watt incandescent putting out approximately 145 lumens.

Miniature LED Bulb BAY15D great for 6 to 12 Volt DC applications, 6V to 12V negative ground or negative chassis. Available multiple colors, please check. 360 Degree viewing angle. Uses the latest technology 5730 SMD Samsung chips up to 320 Lumen output for brake light. This product is polarity sensitive. Please see other same product that is non polarity sensitive. Uses about 2.6 watts. Up to 135 Lumen output for taillight. 6 to 12 Volt DC applications only. Please make sure your application only provides 6 up to 12 volts max DC under a LED load condition. CE and Rohs listed. Made with quality 5730 SMD Samsung led's for long life. This bulb is very bright two filament the brake light and the tail light. This LED bulb is not dim-able. Comparable to a 25 to 30 watt incandescent bulb.

1158 Miniature LED Bulb for old vintage and classic cars. 2 filament or brightness levels. For Negative ground vehicles. Operates from 6 to 12 volts DC. 360 degree illumination. This is a BA15D base product. Long life up to 30, 000 hours. Latest technology 5730 SMD LED chips for very bright and long life. The bulb fits the outline of a normal incandescent bulb. UP to 270 lumen output for tail light, up to 320 Lumens for brake light. 1158 for older negative chassis 6 to 12 volt cars or motorcycles, tractors. The difference between a 1157 and 1158. The 1157 the bayonets are offset while the 1158 are the same height. The diameter of the base is 15mm so it will fit your fixture if 1158 style. Long life up to 30,000 hours. Comparable to a 25 Watt to 35 Watt incandescent light bulb. If the tail light is brighter than the brake light please rotate the bulb 180 degrees. CE and Rohs.

6 volt led flasher negative ground. This flasher operates negative ground up to 150 Watt's. This flasher is rated from 5 to 8 volts. The flasher eliminates hyper flashing so no load equalizers required. After market turn signal controllers can cause load equalization issues. After installation you still have issues please install load equalizers. The rated flasher flashing time is 400 hours. The flasher relay clicks like a real old time flasher so you can hear that you have your flasher on. The duty cycle ranges from 30% to 70%. Please connect your anode of your LED to the L terminal. Please connect your cathode of your LED to ground. The anode is the positive terminal of the led if you are not sure please hook your led up to your battery to see which side is the anode and which side is the cathode. The rated load is from 1 amp to 20 amps. The rated wattage is up to 150 Watts.

E10 Screw (T10) Concave LED Light. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green, blue and rgb. .02 mA@13.8VDC 345mW. Approximate size is .90in x .39in 10mm (height x diameter). Operates from 6 to 12 volts DC. Up to 7 Lumen output. The viewing angle is 60 degrees.

3798 5 LED Bulb 6 Volt negative ground. This bulb dim-able using a variable voltage such as your dashboard dimmer. Uses about 1.5 Watts at 6 Volts. The Lumen output is about 40 Lumen side firing and 70 Lumen forward firing. Vehicles, tractors, trucks and motorcycles that were bulb pre world war II. The bulb is CE and Rohs listed. This 6v led bulb will fit all vehicles that require a BA7S bulb. This bulb is a available in White 6000K and Warm White 3000K. This BA7S will fit old dashboards, instrument panels, military, marine applications and other retrofit applications that require 6v T7 BA7S led bulb. T2 1/2 or T2.5 tubular bulb shape. Single filament design. Compatible with the following: #3798 #1262 LLB282 #4050

81 LED Bulb 6 Volt Positive Chassis or Negative Chassis Miniature bulb. This bulb will work on AC or DC voltage. The maximum bulb length is 1.24 inches and the maximum diameter is is .75 inches. This will fit the small size of a #81 light bulb. BA15S single contact. G6 single contact bayonet LED. C-6, C-2R filament design compatible, single filament Uses only 1 Watt at 6 volts. Uses very low power. The profile is very small to match the profile of the #63 bulb. The light output is up to 90 Lumens the #63 bulb has a rated output of 3 candle power CP, the LED is up to 6 candle power so about twice as bright as stock light bulb. This bulb is available in White 6000K, Warm White 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Long life up to 30,000 hours.

Third brake light for 6 volt positive ground or negative ground vehicles. Available in Red and Yellow/Amber. Up to 320 Lumen output for the brake light and up to 250 Lumen output for the taillight. Made with 50 quantity 3030 high output led chip's. The black wire is ground, the white wire or yellow wire is for taillight or running light. The red wire is for brake light. If you do not want to use the taillight please just leave the white wire not connected. The length is 3" long and 3/8" wide. The flexible strip is rigid. The third brake light has some water resistant materials. Uses 113mA@6V for the taillight and 220mA@6V for brake light. The approximate power consumption is up to 1.2 Watts for brake light and up to .8 Watts for tail light. Comparable to a 10-15 Watt incandescent bulb.

159 led Bulb for 6 volt Negative Chassis 159 T10 wedge. Great for old vehicles that were built or constructed before world war II. These older vehicles and motorcycles have a 6v negative chassis. This T10 miniature bulb glass wedge will work in these old classic, vintage cars. The T10 rated voltage is 6 volts. Up to 30 Lumen side firing and 70 Lumen forward firing. Up to 1 Watt at 6 volts. Comparable to a 8 to 10 watt incandescent bulb. This led bulb fits arcade games, pinball machines and amusement rides that require 6 volt DC mini T10 wedge. This bulb also replaces 6.3V or 6V. This led bulb is a great replacement for glass wedge incandescent bulb. This bulb is T3-1/4, T3.25 shape meaning tubular and 3-1/4 wide. CE and Rohs listed. Dim-able using a variable voltage supply such as the dashboard dimmer. Great for dome, glove box, dashboard, panel, license plate and other accessory lighting.

T7 BA7S LED Light. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 6 to 12 VDC negative chassis. The M.O.D. maximum overall diameter for the body is 6.8mm. The M.O.L maximum overall length is 17.85mm. Approximately up to 7 lumen output. Operates 6 to 12 Volts DC. T7 BA7S male base. The led bulb shape is T2 1/2. Dimmable with a variable voltage supply such as your dashboard dimmer switch. Viewing angle 120 degrees. The available colors are White 6000, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Great for negative ground vehicles and motorcycles. Comparable to a 4 to 9 Watt incandescent bulb. CE and Rohs. Compatible with: N177221 N 17 722 1 LLB 281 Instrument Dash Lights Philips 6829 Porsche 90063100190

1154 Miniature LED Bulb 6 Volt. This lamp will operate either Positive Ground or Negative Ground. BAY15D dual contact offset indexed bayonet LED. Dual filament. The #1154 has both a tail light and a brake light. There are two contacts on the bottom. One contact is for taillight. One contact is for brake light. The base is 15mm diameter. The bayonets are offset. Uses up to 1 Watt at 6 volts. Approximately uses 166mA @ 6 Volts. Uses very low power. The profile is very small. The overall length is 1.25 inches and the diameter is .59 inches. The light output is up to 200 Lumens for brake and 150 Lumens for taillight. The bulb brake light has a rated output of up to 16 candle power CP. The taillight has a rated output of up 11 candle power CP. This bulb is available in White 6000K, Warm White 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Long life up to 30,000 hours.

The BA9S led bulb is designed to operate at 6 volt ac or dc for both positive ground and negative ground vehicles. Small outline to match the outline of a 51 bulb. .7 inches long by .46 inches wide at the plastic ring. The base is .39" wide. Up to 135 Lumen output. The led's are small 7020 smd so they are very low profile. The life is up to 30,000 hours. The bulb is comparable to a 4 to 10 watt halogen light bulb. The viewing angle of the 7020 LED's is 120 degrees. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow/Amber. CE and Rohs listed. These led's are 80% energy savings really helps the low power generator provide power. This led bulb is dim-able using a dimmer switch or variable voltage supply. These led light bulbs work great for instrument panels using the different colors. Since led's generate their own color no plastic colored caps or painted light bulbs needed.

For vehicles that are negative ground. Up to 40 lumen forward firing, and 40 lumen side firing, 6 volt DC, CE, Rohs listed, low power, long life. Uses about .110A at 6 volt DC. This bulb is dimmable with a variable power supply. Comparable to a 10-20 Watt incandescent bulb.

1 3528 SMD T5 Wedge LED Light Bulb. Very small T5 LED Light with 1 3528 SMD LED. 6 V DC. Available in white only. Uses very little power being surface mount technology. Approximate size is .67in from top to bottom by .21in diameter. T1 3/4. Available in White, Warm White, Red, Green, Yellow and Blue colors. Viewing angle 120 degrees.CE and Rohs listed. Uses approximately 10ma @6V and approximately 8 lumen output. Made with Samsung LEDs.

1142 LED BA15D 6 Volt Positive Ground and 6 Volt Negative Ground. Up to 150 Lumen forward firing, up to 20 Lumen side firing. Available in warm white 3000K and White 6000K. Comparable to a 25 Watt halogen bulb. Approximate size is 1.57in x 1.03in. BA15D base has a single filament. The bayonets are parallel or even and two contacts on the bottom. The diameter of the base is 15 mm. 360 degree illumination excellent choice for reflectors and lens. Dimmable with a variable voltage supply such as your dashboard dimmer switch. This is a single filament led bulb. To apply power you connect ground the one contact and apply plus 6 Volt to the other contact. Comparable to a 15 to 25 Watt incandescent bulb. CE and Rohs.

1847 LED Miniature Bulb works for both 6V positive ground chassis or 6V negative ground chassis. The led bulb is non-polarity 6 Volt BA9S. Sub miniature bayonet. Up to 80 Lumens, about 40 forward firing and 40 Lumens side firing. Up to 3 CP candle power forward firing and up to 3 CP candle power side firing. This bulb is dim-able using a variable power supply such as the dashboard dimmer knob. Rated life up to 30,000 hours. Uses .09 Amps @ 6 Volts. Up to 1 watt LED power comparable to a 10 Watt incandescent bulb. Made with six 5630 SMD led chips. Overall length 1.097" and .47" diameter. T3 1/4 Tubular package. Great for vintage, classic, cars, trucks, tractors, scooters or motorcycles. Excellent replacement for pinball, arcade and amusement rides.

1158 Bulb 6V 24 LED. Works either 6 Volt positive or negative ground. Approximate size is 1.57in x 1.03in. Up to 180 Lumen output. Works great for older pre World War II vehicles. Available in White 6000K, Red, Green, Blue, Yellow. Dual filament BA15D base. If tail light comes on brighter than brake light must rotate the bulb 180 degrees. Comparable to a 20 to 25 Watt incandescent bulb. The base is BA15D which means there are two contacts on the bottom. The bayonets are parallel. If the tail light is brighter than the brake light please rotate the lamp 180 degree's. Uses around 1.8 watts. The Lumen output for low is up to 160 Lumens. The high is up to 210 Lumens. The low beam side firing is up to 40 Lumen. The low beam forward firing is up to 120 Lumens. The high beam side firing is up to 53 Lumen. The high beam forward firing is up to 110 Lumen.

Small outline to match the 55 Miniature bulb. .7 inches long by .46 inches wide at the plastic ring. The base diameter is .39". Up to 135 Lumen output forward firing or up to 10 CP candle power. The led's are small 3030 smd so they are very low profile. Each 3030 smd can output up to 130 Lumens. The BA9S base is designed to operate at 6 volt ac or dc for both positive ground and negative ground vehicles. The life is up to 30,000 hours. This led lamp is dimmable using a variable voltage supply such as a dashboard dimmer. The bulb is comparable to a 4 to 10 watt halogen light bulb. The viewing angle of the 3030 LED's is 120 degrees. Available in White 5500K to 6500K, Warm White 2700K-3300K, Red, Green, Blue and Yellow/Amber. CE and Rohs listed. This bulb uses 90% less energy great for old generators. Uses .079mA at 6.8 volts. Compatible with the following: GE 51 Mazda 55 55N 755

1482 LED Bulb E10 miniature screw base 6 Volt positive chassis or negative chassis. Since the E10 is no polarity or non polarity. The bulb low profile, long life up to 30,000 hours, low voltage. The bulb uses approximately 1 Watt at 6 Volts. Approximately 70 Lumen output. Single filament design. Long life. Low voltage for 6 volt only positive ground or negative ground applications. See product detail for warranty period. Available in white 6000k, warm white 3000k, red, green, blue and yellow. This led bulb is dim-able using a variable AC power such as the dimmer knob on the dashboard. Since this bulb is non polarity works great for pre world war II vehicles and motorcycles. Upgrade to this bulb for license, running, turn signal, interior for long life and low power. Since this bulb is non polarity you do not have to worry how the existing socket is wired since this bulb is non polarity.

82 LED Bulb. BA15D Base. 6 Volt Positive Ground or 6 Volt Negative Ground. Up to 200 Lumen output. Up to 15 Candle Power. The maximum length is 1.25 inches and the maximum diameter is .75 inches. Comparable to a 10 to 25 Watt incandescent bulb. The L.E.D. bulb C-6 filament design. Single Filament. Uses up to 2 Watts @ 6 Volts. The base is BA15D with even bayonets. The lamp only has one brightness level. The bulb is dim-able using variable voltage supply such as dashboard knob. Great for license plate, turn, tail, brake, dome, dashboard, instrument panel lamps. The LED color is created by the material of the LED so it looks real nice monochromatic. The available colors are White 6000K, Warm White 3000K, Red 626nm, Green 526nm, Blue 646nm and Yellow 594nm. The old light bulbs were painted. Very low profile to fit Ford Model A cowl light. Long life up to 30,000 hours.

Use this festoon for classic or antique automobiles or cycles that use 6 volt chassis. This led bulb works with negative chassis systems. The bulb uses about 3 watts at 6 volts. This bulb is dimmable with a variable power supply. The leds provide 360 degree illumination. The festoon is comparable to a 20 to 25 incandescent light bulb. This festoon works great for pinball machines that operate at 6.0 volts DC. Replaces Volkswagen Beetle light bulb: 43mm. Approximate size length 1.71" and the diameter is .45". N177231 N 17 723 1 4203 JAHN 1730

6 Volt no polarity festoon for older negative chassis automobiles or cycles. Zero to 6 Volts DC. Long life up to 30,000 hours. 360 degree illumination. Up to 70 lumen output. Great size outline to the same shape as a incandescence festoon. Comparable to a 10-20 watt incandescence festoon.

Used with a LED Light to simulate that the original light bulb is installed. Easy to install. Keep away from plastic or painted surfaces, resistor gets very hot. Connect the load equalizer in parallel with the led light you are replacing. Includes 7" of 20 awg stranded Teflon wire. 2 wire crimps included. Use one 6 Ohm 25 Watt equalizer for each LED bulb, or use one 3 ohm for 2 led bulbs for each turn signal control side that you replace. For a 6 Ohm load equalizer you can attach up to 1 LED light per equalizer. For the 3 Ohm load equalizer you can attach up to 2 LED lights per equalizer. Load equalizer dimensions are 0.75 inches in length and 0.42 inches wide. No special tools needed just a pair of pliers. The connection is made using insulation displacement connectors. This load equalizer eliminator capacitor operates from 6 to 12 volt positive ground or negative ground.

p45t LED Headlight 6 volt. Up to 650 Lumen output or 60 CP. Dual filament high and low beam. Made with 5730 smd leds for long life. Rohs and CE listed. Designed for easy installation, just remove old headlight and insert new headlight. Works both 6 volt positive ground and 6 volt negative ground. Great for old classic and vintage automobiles, motorcycles and tractors. Available in white 6000K and warm white 3000K. Long life up to 30,000 hours. Comparable to a 45 to 55 watt incandescent bulb. The maximum overall length is 1.944 inches. The maximum diameter is .760 inches. The pin out as follows when looking at the connector from the rear. The left most contact is ground. The center contact is low beam. The right most connector is high beam. This lamp will fit a standard H4 HB2 9003 3 prong female Socket connector such as part number 34265.

Used with a LED Light to simulate that the original light bulb is installed. Easy to install. Keep away from plastic or painted surfaces, resistor gets very hot. Connect the load equalizer in parallel with the led lamp you are installing. Approximate 6" of 20 AWG stranded Teflon wire. 2 wire crimps included. Use one 6 Ohm equalizer for each LED bulb, or use one 3 ohm for 2 led bulbs for each turn signal control side that you replace. Use one 20 Ohm or 100 Ohm for each side marker. For a 6 Ohm load equalizer you can attach up to 1 LED light per equalizer. For the 3 Ohm load equalizer you can attach up to 2 LED lights per equalizer. Load equalizer dimensions are 0.75 inches in length and 0.42 inches wide. (3 ohm equalizer is slightly larger). No special tools needed just a pair of pliers. The connection is made using insulation displacement connectors.

BA15S LED Bulb works in positive or negative ground vehicles. Single filament lamp. Operates 6 volts non polarity. Super bright led lamp using the latest high power 3030 SMD led. Each 3030 SMD can emit up to 30 Lumen output. Up to 400 Lumen output. Up to 31 CP candle power. Uses up to 3 Watts. Super low profile to fit the small cowl lights, indicator, taillight. Viewing angle is 120 degrees. Comparable to a 25 to 30 watt halogen light bulb. Available in White 6000K, Warm White 3000K, Red 625 nm and Yellow Yellow 594 nm. Extremely long life up to 30,000 hours. Solid-state never have to worry about a broken filament with led lamps. Compatible with early vintage cars, trucks and motorcycles. Dimmable with a variable voltage supply such as your dashboard dimmer. Single Contact Bayonet where the bayonets are parallel to each other with one contact at the bottom. Compatible with the C6 Filament shape.

LED Headlight Load Equalizer works from 6 Volt to 12 Volt classic and vintage cars and motorcycles. Works either positive ground or negative ground. Please use a load equalizers for your low beam, one per side if your headlights are not working properly after installation. Sometimes after upgrading the older car electrical system does not recognize the new technology. Since led headlights use 80% less power, sometimes load equalizers are needed. Please connect the load equalizer in parallel with the low beam circuit. To connect parallel means one end of goes to the chassis and the other end connects to your low beam. Please use one per the left headlight and right side headlight. Included are insulation displacement crimps IDC. The IDC are easy to install using pliers and easy to remove. Recommended to install to the metal of the car to help dissipate the heat.

This universal led flasher will work negative ground vehicles, motorcycles and scooters. Operates from 6 to 15 Volts. Included are 7" of wire and quick disconnect crimps for easy installation. Flashes 60 times a minute. The load is from .5 Watt up to 20 Watt for led bulbs only. Please see diagram. CE and Rohs.

T19 P15D-25-1 base led headlight. Up to 600 Lumen output. Dual filament Low and high beam. Long life up to 30,000 hours. The leds are optically aligned for best led light output using your reflective fixture. Please always clean the fixture when installing led light bulb. Comparable a 25 to 35 Watt halogen or incandescent bulb. The base is T19 P15D-25-1 base. This bulb operates either AC or DC. Operates at 6 volts, higher voltage with cause this bulb to fail. The bulb can operate up to 7.0 volts. Works either positive chassis or negative chassis. The M.O.L. maximum overall length is 1.976" and the M.O.D. maximum overall diameter is .747" not including the base diameter. CE and Rohs. Compatible with: p15d-25-1 PX15d H6 h6m P15D Honda TL125 125S 250 C105T 110 CT70 90 Honda 1970 mini trail Honda vintage mini trail 10-527-84114-09-xx

1154 LED Bulb 6 Volt. BAY15D base 1154. 60 LED Light bulb. Very bright up to 950 Lumens brake light. Up to 750 Lumens taillight. Operates 6V positive ground or 6V negative ground. BAY15D base 2 contacts tail light and brake light. One bayonet offset higher than the other bayonet. Long life up to 30,000 hours. Comparable to a 35 to 55 watt halogen or incandescent lamp. CE and Rohs listed. The leds are optically aligned to the reflector for maximum led light output. Up to 70 CP candle power output. Dim-able with a variable voltage supply. The BAY15D base is 15mm diameter with one bayonet indexed and two contacts. The maximum overall length M.O.L. 1.944 inches. The maximum diameter is 1.058 inches. Please make sure this bulb will fit your fixture. Uses about 1 Amp @ 6.3 Volts.

1158 6 Volt LED Bulb for both positive and negative ground vehicles and motorcycles. Up to 400 Lumen output for high beam and 360 Lumen for low beam. This bulb uses BA15D base that has two contacts and two bayonets. The bulb has two filament design. If the bulb is dim and should be bright just remove and reinsert 180 degrees. Comparable to a 25 to 35 watt incandescent bulb. Viewing angle is 120 degrees. The led lamp is dim-able using a variable voltage supply. Since the bulb is dim-able works good in the vintage and classic vehicles that the voltage is not up to 6 volts due to old wires and connections. White 6000 K, Warm White 3000 K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Up to 31 candle power. Maximum overall length MOL is 1.944 inches. Maximum diameter is .741 inches. CE and Rohs listed. Please see bottom of detail page for extended warrant details. Up to 30,000 hours life.

1154 6 Volt non polarity BAY15D. The Lumen output for brake light is up to 220 Lumens. The Lumen output for taillight is up to 150 Lumens. The approximate is 0.740" diameter and 1.023" length. The bulb is dimmable. The max voltage is 7.5 volts. The minimum required voltage is 5 volts. Long life up to 30,000 hours. Uses up to 90% less energy than a incandescent bulb. Comparable to a 15 Watt to 25 Watt incandescent bulb. CE and Rohs. Available in red, green, blue, yellow, white 6000K and warm white 3000K. The white 6000K is about 5% brighter than the warm white. The diameter of the base is 15mm. The bayonets are offset. There are two contacts on the bottom. CE and Rohs.

BA15D LED Headlight 5 To 30 Volt Single Filament Non Polarized. Up to 1800 Lumens. 1142 Configuration meaning ground on one contact and 5 to 30V on the other contact. Up to 30,000 hours for long life. Great for older vehicles generators. Easy to install remove old bulb and install this lamp. Works either positive ground or negative ground. Body made of aluminum for long life. Available in 6000-6500 Kelvin. Great for 6 volt, 12 volt up to 30 volts. Load equalizers may be required, if the bulb will not switch from low beam to high beam or if the bulb flickers when installed. Please install led light load equalizers to fix the problem product code 65832. Full bright at any voltage from 5 Volts to 30 Volts. Uses approximately 1.4A @ 6 volts. Overall length is 2.52 inches. Width is 0.98 inches. Length of the body above the BA15D base is 1.77 inches. Compatible with: 1130

Headlight housing 7" round DOT compliant with T10 5 Watt parking bulb. This assembly allows you to install your own led, hid, xenon or halogen bulb. The assembly accepts P43T H4 headlight bulb. These DOT headlamp assemblies are designed for USA right hand traffic LHD. The headlight housing is made of plastic. The assembly is CE and Rohs listed. The headlight semi sealed housing assembly has a clear lens. This assembly works great for vintage and classic vehicles with older faded glass or plastic headlights. For 6 volt positive ground and 6 volt negative ground vehicles you can use our 6 volt led bulbs and upgrade you old vehicle to led lighting. Easy DIY just remove existing headlight assembly and install this semi sealed headlight assembly usually by 3 screws. This headlight works good for motorcycles, scooters and tractors that are old and either 6 or 12 positive and negative ground systems.

1142 LED Miniature Bulb for positive or negative vehicles. Up to 500 Lumen output. Single filament C-6 design. BA15D base has two contacts and the bayonets are parallel to each other. Long life up to 30,000 hours. These LEDs are optically aligned so that the leds output the maximum light to the reflector and lens. This bulb is dimmable using a variable voltage supply. Since the bulb is dim-able works good when the voltage is not a peak voltage of 6 volts and will stay lit dimmer as the voltage goes down. For old vintage and classic cars this is a simple D.I.Y. do it yourself job. Please disconnect power, remove old bulb and insert new bulb. Comparable to a 25 to 35 Watt incandescent light bulb. CE and Rohs listed. The color options are white 6000k, warm white 3000k, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Extended warranty, please see bottom of product detail page for warranty details.

63 LED Bulb. Operates 6 Volt for vintage cars, trucks and motorycles. The base is BA15S single contact. Single filament. Up to 240 Lumen output or up to 18 CP. The lamp has 8 3030 smd. Each 3030 smd can output up to 30 Lumens. Works positive ground and negative ground. Super low profile to fit sockets that have fingers. Amazing long-life up to 30,000 hours. Uses 90% less energy. CE and Rohs. The base is 15mm diameter with two bayonets same height. Available in white 6000k, warm white 3000k, Red 625nm, Yellow 594nm, Green 526nm and Blue 464nm. Great for license plate lights. The viewing angle is 120 degrees. This bulb is dimmable using a variable voltage such as your dashboard dimmer. Upgrade your old lamp to a new super bright led. Your generator/alternator will be happy 90% less energy used. The shape is G6.3.0 MSCP. The filament design is compatible with C-6.

1158 Miniature LED Bulb operates 6V positive or negative ground vehicles. Up to 200 Lumen output for brake and 150 Lumen output for taillight. Long life up to 30,000 hours. Dual filament one filament for low beam and one filament for hi beam. BA15D base has two contacts and the bayonets are parallel to each other. This bulb is dim-able using a variable voltage supply. Since dim-able works great in vintage and classic vehicles that the electrical system is not full voltage. White 6000 K, Warm White 3000 K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. The M.O.L. is 1.25". The diameter is .59".

BA9S 6 Volt DC Short round L.E.D. Light. Use this led bulb for lower voltage applications. CE and Rohs listed. Long life up to 30,000 hours. Approximate 7 Lumen output, 120 degree viewing angle. Uses approximately 25mA. @13.8VDC 345mW. Available in White 6000K, Red(625nm), Blue(464nm) & Yellow(594nm). The white color will start to illuminate around 2.6 volts DC and gradually get brighter up to 6 volts DC. This bulb is dim-able with a dashboard know or variable voltage supply. This bulb will work on 6 Volt negative ground vehicles. Comparable to a 4 to 9 Watt incandescent bulb. Compatible bulb: 51 55

BA15D 6 Volt 60 SMD 5730 Single Filament Reduced Profile. This bulb operates 6v positive ground or 6V negative ground. Up to 900 Lumen output. Up to 340 forward firing Lumens and 560 side firing Lumens. Long life up to 30,000 hours. Made with total 60 leds, 44 side firing and 16 forward firing. This lamp is a single filament bulb. The base has even bayonets and two contacts on the bottom. This bulb is only designed for 6 volt vintage vehicles, motorcycles and scooters. Please make sure you voltage is regulated to 6 volts. The light bulb can be dimmed with a variable voltage supply if needed. The leds are aligned to be the optimum height for maximum light output using a reflector and lens. Available in White 6000K, Warm White 3000K, Red and Yellow. Maximum overall length is 1.694". The maximum diameter is 1.058". These lights led are solid state for low power and super long life.

H4 P43t base 6 Volt LED headlight for vintage vehicles and classic motorcycles. This led is designed for 6 volt motorcycle headlights. Works either AC or DC voltage. Very bright. Dual high and low beam. Up to 750 Lumen output. Comparable to a 50 - 75 Watt incandescent bulb. Made with the latest smd leds 5730. The profile of the led fits inside of a normal light bulb so you know it will fit your application. Operates either 6v positive ground or 6v negative ground. Up to 650 Lumens for high beam and up to 510 Lumens for low beam. This headlight bulb is up to 50 candle power CP for high beam. Up to 40 candle power CP for low beam. Long life up to 30,000 hours. This bulb uses approximately .490 amp @ 6.9 volts for hi beam. The bulb comes in White 6000K and Warm white 3000K. The Warm White simulates the original color of a incandescent light bulb.

6 Volt Festoon works with Positive Ground or Negative Ground. Up to 2 Watts of LED power. This festoon has 150 to 200 Lumen output. The led's are designed so that light lights in 180 degrees. This festoon is great for vintage, classic and antique cars, trucks and motorcycles. Vehicles made before World War II have a 6 volt positive chassis or 6 volt negative chassis. Since these LED's are AC non polarity they work great in these old vehicles. Long life up to 30,000 hours or longer. Available in White 6000K and Warm White 3000K. Comparable to a 15 to 20 Watt glass festoon incandescent light bulb. This festoon works great for pinball machines that are 6 volt AC systems. Certain amusement games and rides use 6 volt AC festoon so these are the perfect replacement. Long warranty please see warranty length on this detail page. The festoon viewing angle is around 240 degrees.

Festoon 6 volt for Positive Ground and Negative Ground vehicles. Up to 200 Lumen output. Long life up to 30,000 hours. Works non polarity AC or DC. Made with 6 5730 SMD high power leds. Available in White 6000 Kelvin and Warm White 3000 Kelvin. Vehicles and motorcycles made before World War II are positive chassis and this led bulb works perfectly. This led bulb is comparable to a 15 to 20 Watt incandescent glass festoon. The end caps are plated for rugged long life connection. Easy to install just remove the old festoon and insert the new led festoon plug & play. Since the new led festoon is non polarity you do not have to worry which way to install the bulb. Great replacement for 6 volt version of: 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 ED3022 DE3175 DE3425 De44101284 6450 This is a perfect replacement for glove box and console lighting upgrades.

6 volt festoon positive chassis or negative chassis non polarity. Up to 200 Lumen output. 1 1/4 length. Uses only 2 Watts, comparable to a 15 to 20 Watt glass festoon incandescent bulb. Since it is non polarity just insert into the festoon socket. Long life up to 30, 000 hours. Available in White 6000K and Wam White 3000K. The festoon end caps are rugged for secure electrical connection. Since the bulb is LED you do not have to worry about the filament breaking or the glass breaking. Great for arcade games and pinball machines. Since the festoon illuminates 180 degrees works great to illuminate the 180 degree viewing angle. The Warm White is closes color to a incandescence light bulb. The festoon has 6 chip high power 5730 SMD LED's. The diameter is .41 inches. Replaces 6 volt version of 3021 3022 3175 6428 6430 30922 De3425 C5W. The light is very clean and vivid.

p45t led headlight. Operates 6 volt positive ground or 6 volt negative ground. Up to 900 Lumen output or 70 CP for high beam. Up to 600 Lumen output for low beam. Available in warm white 3000k and white 6000k. Long life up to 30,000 hours. Since led's are solid state you do not have to worry about a broken filament or glass. CE and Rohs listed. Dual beam low and high beam. Works great for old vehicles made before World War II such as Ford Model A's and T. Easy DIY replacement just remove old incandescent and replace with new led bulb. Since led's use up to 90% less energy they really help the old generators and alternators with such a reduced load. Comparable to a 55 to 65 Watt incandescent bulb. The maximum diameter is 1.058" inches. The maximum overall length is 1.944 inches. Fits standard connector such as part number 34265. The pin out looking from the back is: Left side contact is ground.

H3 LED Bulb 8 Volt Positive ground or Negative Ground. Has a PK22s base. Up to 400 Lumen output. Long life up to 30,000 hours. Fits H3 sockets. Dim-able. Great for vintage automobiles and motorcycles. Solid state do not have to worry about broken filaments. Comparable to a 45 Watt incandescent bulb. Works great in old vintage 8 Volt to 9 Volt Fords. Available in White 6000K and Warm White 3000K. CE and Rohs. Comparable to a 35 to 45 Watt incandescent. CE and Rohs. The thickness is approximately 0.2". The dimension from the decking to the top of the bulb is 1.5". The overall length is 1.89" and the diameter of the decking is 0.86". The width of the bulb is 0.45".

BA15S LED Bulb works in positive or negative ground vehicles. Single filament lamp. Operates 8 volts non polarity. Super bright led lamp using the latest high power 3030 SMD led. Each 3030 SMD can emit up to 30 Lumen output. Up to 400 Lumen output. Up to 31 CP candle power. Super low profile to fit the small cowl lights, indicator, taillight. Viewing angle is 120 degrees. Comparable to a 25 to 30 watt halogen light bulb. Available in White 6000K, Warm White 3000K, Red 625 nm and Yellow Yellow 594 nm. Extremely long life up to 30,000 hours. Compatible with early vintage cars, trucks and motorcycles. Dimmable with a variable voltage supply such as your dashboard dimmer. Single Contact Bayonet where the bayonets are parallel to each other with one contact at the bottom. Compatible with the C6 Filament shape. The maximum overall length M.O.L. is .888 inches. The maximum bulb diameter is .748 inches.

Super bright 12 One Watt LED's 12 Volt DC. Works only negative ground vehicles. Can use BA9S or T10 Wedge or 36mm Festoon. Available in White 6000K. Up to 1200 Lumen output. 120 Degree viewing angle. Dimmable with a variable voltage supply. Has double sided sticky tape on the back side. CE and Rohs.

BA15D 1158 6 Volt 60 SMD 5730 Dual Filament Reduced Profile. This bulb operates 6v positive ground or 6V negative ground. Up to 900 Lumen output for brake light and up to 500 Lumens for tail light. Up to 72 candle power CP for brake light and up to Up to 40 candle power for taillight. 340 forward firing Lumens and 560 side firing Lumens. Long life up to 30,000 hours. Made with total 60 leds, 44 side firing and 16 forward firing. This lamp is a two filament bulb. The base has even bayonets and two contact on the bottom, BA15D. This bulb is only designed for 6 volt vintage vehicles, motorcycles and scooters. Please make sure you voltage is regulated to 6 volts. The light bulb can be dimmed with a variable voltage supply if needed. The leds are aligned to be the optimum height for maximum light output using a reflector and lens. Available in White 6000K, Warm White 3000K, Red and Yellow.

1154 Bulb LED BAY15D Base 8 Volt 2.6 Watt. Works either negative ground or positive ground. Long life up to 30,000 hours. Uses only 2.6 Watts. Comparable to a 25 Watt halogen bulb. Has dual filament low beam and high beam. The bayonets are offset. The base has 2 contacts. The base diameter is 15mm. The MOL is 1.47". The MOD is .78". Available in White 6000, Warm White 3000K, Red, Green, Blue and Yellow. CE and Rohs. Up to 320 Lumen for brake light and 240 Lumen for tail light. This bulb is dim-able using a variable voltage supply. Use load equalizer per each led bulb that used in a turn signal circuit. Please use our solid state flasher with load equalizers. Works from 6 Volts up to 10 Volts. CE and Rohs.

H3 LED Bulb 6 Volt Positive or Negative Ground. Has a PK22s base. Fits H3 sockets. Operates 6 Volt Positive ground or negative Ground. Dim-able. Up to 200 Lumen output. Made with no breakable parts completely solid state. Available in White 6000K and Warm White 3000K. Comparable to a 40W to 50W incandescent bulb. The maximum overall length is 1.875" that is from the top to bottom of the bulb. The width of the bulb not including round flange is .453". The round flange maximum diameter is .866". The thickness is approximately 0.2". The dimension from the top of the decking to the top of the bulb is approximately 1.5" The CE and Rohs.

P36D base 5 to 30 volt positive ground or negative ground. Made with 16 2525 leds. Made with aluminum to keep the leds cooler so they last longer. This bulb is non polarized. Up to 1800 Lumen output for high beam up to 1200 Lumen output for low beam. Uses only 1.4 Amps high beam and .8 Amps for low beam. Long life up to 30,000 hours. Easy to replace just remove old bulb and insert new led bulb. CE and Rohs listed. Comparable to a 55W to 65W halogen bulb. This retrofit take around 1 minute to change the the old bulb. Dimensions are overall length is 2.52 inches. The width is 0.98 inches. Load equalizers may be required, if the bulb will not switch from low beam to high beam or if the bulb flickers when installed. Please install led light load equalizers to fix the problem product code 65832. Available in 6000K to 6500K. Compatible with: 312 30/24W 6 VOLT PRE-FOCUS Lucas 446, 414, 370, AND 312

H4 P43T led headlight bulb, works for both positive ground and negative ground vintage and classic vehicles, cars, trucks, motorcycles and scooters. 1:1 LED headlamps. These lamps are 1:1 plug and play lamps. They have the same clear cut-off line beam patterns as the original bulbs do, but much brighter and more compacted. The lamps are made with 8-chips high power 3570 LED's. Uses approximately 1.47A@8V for both low beam and high beam. The real output reaches up to 1800 Lumens per headlight bulb. Up to 144 CP candle power per led bulb. Comparable to a 55 to 65 Watt incandescent bulb. These CSP led's are very close to the original filament size for the best conversion to led. The mini-inside fan runs very differently from the ones in the market. They are rare to fail! And even if by any chance the fan fails, the lamp will work the same. Classic vehicle and heavy truck lighting area.

Third brake light for 6 Volt positive ground or negative ground vehicles, motorcycles or scooters. The LED third brake light has both taillight and brake light dual filament. The third brake light is 9" long and 3/8" wide. Great for older classic and vintage cars, trucks and motorcycles. The led third brake light has 3 wires, black if for ground positive or negative ground, yellow or white for taillight and red for brake light. The wire is 22 AWG gauge stranded. The wire is about 3.5" long. The light is flexible so it can be mounted on a curved or flat surface. Since some old vintage and classic cars have only one brake light this can be the second or third led brake light. Available in Red 625nm. There are 14 5050 led's, each led outputs about 22 Lumens for up to 308 Lumen output. The viewing angle is 120 degrees. .220A@6V for brake light and .077A@6V for taillight.

BAY15D LED Headlight 5 to 30 Volts. Non Polarity. Dual Filament. High beam up to 1800 Lumens. Low beam up to 1100 Lumens. Uses approximately .8 Amp for low beam. For high beam around 1.5 Amp. Made of aircraft aluminium to help keep the leds cool so the last longer. The base is 15 mm diameter. One bayonet is offset BAY15D base. There are two contacts on the bottom for low and high beam. Operates from 5 to 30 Volts which works good for older Fords that are 8 Volt. Helps your generator or alternator by using 80% less power than a incandescent or halogen bulb. Comparable to a 55 Watt halogen for low beam and 65 Watt for high beam. Made with high power led for long life. Operates in a wide voltage constant current meaning that this lamp will draw the same amps for wide range from 5 to 30 Volts.

6 Volt LED Bulb Non Polarity T10 Wedge. Works either Positive ground or Negative Ground. For 6.3 Volt AC/DC non polarity vintage and classic vehicles and motorcycles, scooters. 120 degree viewing angle. Long life up to 30,000 hours. Available in White 6000K, Warm White 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Up to 50 Lumen output. Forward firing led's. Approximate dimensions 0.63" length and 0.44" max width, the wedge is dimension is 0.35" wide. Dimmable, comparable to a 4 to 9 Watt incandesce bulb. Fits a standard T10 wedge socket. Compatible with: T10 W5W 192 158 168 194 2825 555. CE and Rohs.

63 LED Bulb 8 to 9 Volt BA15S Base. Designed for 8 Volt Fords. Works both positive ground or negative ground. Up to 18 CP or 240 Lumen output. 120 degree viewing angle. Long life up to 30,000 hours. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow. Single Contact, Single Filament BA15S. The bayonets are even and has one contact and the bottom. The base diameter is 15mm. The bulb is made very low profile to work when used in old sockets that classic and vintage cars have. The bulb is dimmable. Comparable to a 25 Watt incandescent bulb. The shape is G6.3.0 MSCP. The filament design is compatible with C-6. This bulb is a true 63 compatible since the board is mounted inside the ba15s base. The overall length M.O.L. is .888 inches. The maximum bulb diameter is .590 inches. CE and Rohs listed. Compatible with: GM #142303 Mazda bulb GE 63 #1133 TS67

51 Miniature Bulb BA9S Base operates 8 to 9 Volt 3 SMD 7020 LED T3 1/4. Works either positive ground or negative ground. Great for motorcycles or 8 Volt Fords. Long life up to 30,000 hours. 120 viewing angle. Comparable to a 4 to 20 Watt incandescent bulb. CE and Rohs. .7 inches long by .46 inches wide. Up to 135 Lumen output. Outputs up to 10 CP forward firing. The led bulb is dimmable using a variable voltage supply such as a dashboard dimmer switch. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow/Amber. This bulb uses approximately 67mA@8Volts. The bulb only uses approximately a 1/2 Watt of power.

BA15S LED Headlight. This lamp has no polarity, non polarized or bi polar. The led headlight is designed for both positive ground or negative ground. BA15S base single contact. Super bright up to 1,200 Lumen. Headlight has aviation aluminum to keep the leds cool so they last longer. Wide voltage 5 to 30 volts AC or DC. The LED's are csp high power. The circuit board is super conducting aluminum. The headlight uses wide voltage and a constant current design. The leds are on both sides so the led light will project light into the housing. The base diameter is 15mm and has a single contact. The bayonets are the same height. Available in White 6000K to 6500k. Long life up to 30,000 hours. Comparable to a 45 to 55 Watt incandescent bulb. The current consumption is 800mA. The socket is made of copper for maximum conductivity. Dimensions are overall length is 2.52 inches.

BA15D LED Bulb 6 Volt. Up to 900 Lumen output. Up to 700 Lumen for low beam. Dual filament both a brake and taillight. BA15D 2 contact with parallel bayonets. 6 Volt Positive or negative ground vehicles, motorcycles and tractors. Since this bulb is dim-able using a variable voltage supply such as your dashboard dimmer switch. Works great if your vehicle has older wiring where all the volts do not make it. CE and Rohs listed. Comparable to a 35 to 55 watt incandescent light bulb. Viewing angle is 360 degrees. The Smd's are optically aligned with your reflector so you get maximum light output. Available in White 6000 K, Warm White 3000 K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. CE and Rohs listed. Long life up to 30,000 hours. The bulb is led so no more worries about broken filament or glass bulb. The maximum overall length M.O.L is 1.944". The maximum diameter is 1.05".

BA15S 1129 6 Volt 60 SMD 5730 Single Filament Reduced Profile. This bulb operates 6v positive ground or 6V negative ground. Up to 900 Lumen output. Up to 340 forward firing Lumens and 560 side firing Lumens. Long life up to 30,000 hours. Made with total 60 leds, 44 side firing and 16 forward firing. This lamp is a single filament bulb. The base has even bayonets and one contact on the bottom. This bulb is only designed for 6 volt vintage vehicles, motorcycles and scooters. Please make sure you voltage is regulated to 6 volts. The light bulb can be dimmed with a variable voltage supply if needed. The leds are aligned to be the optimum height for maximum light output using a reflector and lens. Available in White 6000K, Warm White 3000K, Red and Yellow. Maximum overall length is 1.694". The maximum diameter is 1.058". These lights led are solid state for low power and super long life.

1142 6 Volt LED Bulb. This lamp has 60 5730 smd leds. Up to 850 Lumen output single filament. The BA15D base has two contacts and the bayonets are parallel. Please apply ground to one contact and 6 Volts to the other contact. The leds are are optically aligned with the reflector for maximum led light output. 360 degree viewing angle. Long life up to 30,000 hours. Dim-able using a variable DC power supply such as your dashboard dimmer switch. Works in both positive ground and negative ground vehicles, tractors and trucks. The 1142 has a single filament, meaning this led is only on and off. CE and Rohs listed. Up to 70 CP candle power. Long warranty please see details below. The color options are white 6000k, warm white 3000k, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. The base is BA15D the diameter of the base is 15mm with two contacts. The overall length is 1.944 inches.

1158 LED Bulb BA15D Base 8 Volt 2.6 Watt G18. Dual filament both tail light and brake light. Up to 320 Lumens for brake light and 240 Lumens for taillight. Long life up to 30,000 hours. Works either positive ground or negative ground. The base has even bayonets. There are two contacts. The diameter is 15mm. Dim-able with variable voltage supply. Available in White 6000K, Warm White 3000K, Green, Blue, Red and Yellow. 8 Volts is designed for 8 Volt Fords. CE and Rohs.

Festoon LED Bulb. 28mm length or 1.1" long. Works 6 Volt positive ground or negative ground. Long life up to 30,000 hours. Up to 50 Lumen output. Available in White 6000K and Warm White 3000K. Dimmable with a variable voltage supply such as a dashboard dimmer switch. Viewing angle 120 degrees. Comparable to 9 to 21 Watt incandescent bulb. Compatible with Volkswagen, Semaphore bulb, VHD-N17-7261, N177261.

BAY15D 1154 6 Volt 60 SMD 5730 Dual Filament Reduced Profile. This bulb operates 6v positive ground or 6V negative ground. Up to 950 Lumen output for brake light and up to 750 Lumens for tail light. Long life up to 30,000 hours. Made with total 60 leds, 44 side firing and 16 forward firing. This lamp is a two filament bulb. The base has offset bayonets and two contact on the bottom. This bulb is only designed for 6 volt vintage vehicles, motorcycles and scooters. Please make sure you voltage is regulated to 6 volts. The light bulb can be dimmed with a variable voltage supply if needed. The leds are aligned to be the optimum height for maximum light output using a reflector and lens. Available in White 6000K, Warm White 3000K, Red and Yellow. Maximum overall length is 1.694". The maximum diameter is 1.058". These lights led are solid state for low power and super long life.

LED headlamp works either positive ground or negative ground. Wide voltage from 5 to 30 Volts AC or DC. Available White 6000K to 6500K or Warm White 2700K to 3300K. No polarity, Bi polarity, non polarized. Made with 16 2525 smd for super bright. The headlamp lights on both sides. Dual filament both a low and high beam. The low beam Lumen output is up to 1200 Lumens. The high beam is up to 1800 Lumens. Great for vintage and classic cars. Long life up to 30,000 hours. CE and Rohs certified. Made with aluminum to keep the led lamps cool so they can operate for a long life. The circuit board is constant current so the leds should not flicker. Available in White 6500k. Perfectly works with product 69854 is a 7" round semi-sealed housing and 68721 is a 5"x7" rectangle housing. Both these semi-sealed housings use the P43T bulb.

For positive ground or negative ground. 5 to 30 Volt wide voltage. Long life up to 30,000 hours. Made with 2525 LED's for long life. Dual filament up to 1200 Lumen low beam. Works both in a socket that is wired for a single filament and works in a ba15d socket that is wired for dual filament. Up to 1800 Lumen high beam. The base is BA15D the diameter is 15mm with two contacts on the bottom and parallel bayonets. Made with aviation aircraft aluminium to keep the leds cool for longer life. Available in White 5000-6000K and Warm White 3000K. Dimensions are overall length is 2.52 inches. The width is 0.98 inches. The length of the body above the BA15D base is 1.77 inches. The circuit board is super conducting aluminum for maximum power supplied the the leds. The led headlamp is a constant current device so the brightness will not fluctuate. CE and Rohs listed.

P36D 5 to 30 Volt positive ground or negative ground non polarized. Made with 2525 led's for long life up to 30,000 hours. High Lumens up to 1200 Lumens. Uses only .8 Amps. Works great for 6 volt vintage cars, motorcycles and tractors. The heat sink is made of aluminum to make the leds operate cooler so they are brighter and last longer. CE and Rohs listed. Comparable to a 45 to 55 Watt incandescent light bulb. Takes just minutes to install. Just remove the old bulb and insert the new led bulb. The base is P36D has one contact on the bottom and diameter of flange is 36mm. Dimensions are overall length is 2.52 inches. The width is 0.98 inches. Load equalizers may be required, if the bulb will not switch from low beam to high beam or if the bulb flickers when installed. Please install led light load equalizers to fix the problem product code 65832. Available in White 6000K to 6500K.

LED light isolator is used when the brake/turn light control module/switch asserts low signal for negative ground when not active or asserts high signal when not active for positive ground vehicles, trucks and motorcycles. This causes your taillights not to work. Works for 6 Volt, 12 Volt or 24 Volt systems. Works for either positive ground or negative ground vehicles. Isolator rated for 10 Amps. Each isolator can dissipate 60 watts @ 6V, 120 Watts@12V and 240 Watts@24V. To install isolator you must cut brake light wire and splice the isolator inline in the brake light circuit. The wires are stranded 18 AWG. Comes with two I.D.C. insulation displacement connectors. No soldering required using the crimps. The wire length is 5" each side for a total of 10" for both sides. The isolator diameter is approximately .4" diameter and .4" in length.

1158 LED Bulb BA15D Base 12 Volt 2.6 Watt G18. Operates either positive ground or negative ground. Taillight up to 240 Lumens, Brake light up to 320 Lumens. Available in White 6000K, Warm White 3000K, Red, Yellow, Green and Blue. Dim-able with variable voltage supply. The base bayonets are even with two contacts. The base diameter is 15mm. The MOL is 1.47", the MOD is .78". Long life up to 30,000 hours. CE and Rohs.

Very bright H1 led headlight bulb. Uses P14.5 base. Works both positive ground or negative ground. Up to 1400 Lumen output. Uses up to 16 Watts. Single filament lamp. Uses aluminum heat sink to keep led's cool so they last longer. Available in White 6000K or Warm White 3000K. Comparable up to 144 Watt incandescent bulb. This headlight bulb can work in 6 volt vehicles, trucks, motorcycles and scooters. Works also in 8 volt Fords. Sold as a pair. This bulb is not dimmable since it is wide voltage from 5 to 9 volts. CE and Rohs.

Operates 7 to 9 Volts positive ground or negative ground. Up to 135 Lumen output. Approximate size 0.7 inches long by .46 inches wide at the plastic ring while the base is .356" which is 9mm. 120 Degree viewing angle. Uses .079mA at 8.8 volts. Comparable to a 20 Watt incandescent. Long life up to 30,000 hours. Great for dashboard instruments. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow/Amber. The light is dim-able using a variable voltage supply such as your dashboard dimmer. This bulb uses 80% less energy than your incandescent bulb, great for old generators. CE and Rohs. Size is a T3 1/4.

5 to 30V positive ground or negative ground non polarity. P45t base, has a notch on the side not shown. Made with 16 Cree 2525 LEDs. Available in 6000K to 6500K. Dual filament the low beam Lumens up to 1200. The high beam Lumens up to 1800. Long life 30,000 hours. Made with aluminum for long life. Uses only 800mA. Uses around 9.6 Watts. Constant current the driver to reduce flicker. The base is P45t. This led bulb is for old vintage and classic cars, trucks, motorcycles, and scooters. Long-life up to 30,000 hours. 8 LEDs on each side for best illumination. When looking at the connect from the rear the ground is the left-most contact. The center contact is the low beam. The rightmost contact is the high beam. Please click on the manual to see the wiring diagram for this bulb. 4 smd chips will be lit for low beam both sides and all 8 smd chips both sides will be lit for high beam.

1129 miniature led bulb 60 smd. 6 Volt positive or negative ground. Very bright up to 900 Lumen output. The bulb is not polarity sensitive so you can use it either positive ground or negative ground chassis. The base is BA15S single contact with bayonets parallel. This bulb is dim-able using a variable voltage supply. Long life is up to 30,000 hours or longer. The viewing angle is 360 degrees. The led's are optically aligned with your reflector for maximum led light output. The bulb has 16 forward firing led's. The forward firing Lumens are up to 340 Lumens. The bulb has 44 side firing led's. The side firing Lumens are up to 560 Lumens. The maximum overall length is 1.944 inches. The maximum diameter is 1.058 inches. The base is BA15S 15mm standard base size with a single contact. Comparable to a C-6 single filament. The bulb is dim-able with a variable voltage supply such as your dashboard dimmer.

6V LED Headlight. Works 6V AC or 6V DC. 60 quantity 5730 smd leds. Optically filament aligned so you get maximum light output through your headlight fixture and lens. The headlight is dimmable using a variable voltage supply. Being dimmable helps out with the older vintage and classic vehicles voltage system and wiring is not 100%. There is a total of 16 forward firing and 44 side firing leds. Each 5730 uses up to 1/2 Watt of power. This bulb up to 950 Lumen or 70 MSCP for high beam. Low beam up to 500 Lumens or 40 CP for low beam. Compatible with C-6 filament designed light bulbs. Comparable to a 30 Watt to 55-56W Watt incandescent light bulb. This bulb works in both 6 volt negative ground and 6 volt positive ground vehicles, tractors and motorcycles. This lamp can operate 6 Volts and has both a low beam and a high beam filament. Long life up to 30,000 hours.

Converts from 12 Volt 4 Amp to 6 Volt 8 Amp. The features are 1. Synchronous rectification technology, the conversion efficiency more than 96%. 2. Internal resistance capacitor filter, withstand high temperature. 3. Almost no heat generated when operated. 4. Chip smart protection, anti-overheating, overcurrent protection. Use this to power your 6 volt powered devices from 12 Volts. Works both positive ground and negative ground vehicles, motorcycles and scooters. It is a good ideas also to put a power switch to turn off the device when not in use. It could be wired to your ignition line where power would be applied when the ignition switch is turned on. Operates from 10V to 35V input voltage. The output is regulated at .1V@6V. The output power is 48 Watts. The Transfer efficiency up to 96%. The Working temperature is -25?-85?. The converter has overheating protection at 150?. The no load current =0.35mA.

82 LED Bulb, single filament. Works either positive ground or negative ground. Bulb has 9 T5 LED's. Up to 200 Lumen output. The bulb has a rated output of 7 candle power CP. BA15D base. The diameter is 15mm and has two bayonets that are even. Single filament with two contacts. Single filament. The available color options are white 6000k, Red 625 nm, Yellow 594 nm. CE and Rohs. Some Warm White 3000K while inventory last. The overall length is 1.25 inches and the diameter is .59 inches. Comparable to a 10 Watt to 25 Watt incandescent bulb. Uses up to 1 Watt @ 6 Volts. Uses approximately 166mA @ 6 Volts. Dimmable with a variable voltage supply such as your dashboard dimmer switch.

#1154 6 Volt Positive or Negative Chassis vehicles, trucks and tractors. Up to 400 Lumen output. BAY15D base meaning two contact and the bayonets are offset. This is a two filament C-6 Design. Since there are two filament one if for tail light and one is for brake light or turn signal. The leds are optically aligned where the original filaments would be so the light output is maximized and not wasted. This bulb diameter is smaller than a normal #1157 and the length is the same so you should not have any issues installing the bulb. The bulb is available in white 6K, warm white 3K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Long warranty please see bottom of the page for more warranty information. This can be used for a 6 volt led brake light or running light. The M.O.L. is 1.962" and the diameter is 0.741". CE and Rohs. Compatible with: 1154 #1154

1129 6 Volt LED for positive or negative ground. Single filament, single contact SC C-6 S9. 30 quantity 5730 SMD LED's. Up to 600 Lumen. The LED are optically aligned to the original filament location. Since the led's are aligned they are able to output to the reflector and lens better light output. Comparable to a 25 to 35 Watt incandescent light bulb. The viewing angle is 120 degrees. The lamp is dimmable using a variable voltage source. Since the lights are dim-able they operate better when there is a low voltage condition. The bulbs are available in white 6000K, warm white 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. The bulbs are non polarity or not polarized so you can use them in sockets that are wired backwards such as RV's and boats. This bulb works great for your vintage or classic vehicle that you want to use led lights.

BA20D LED headlight 5 to 30 volt. The base is rotated 90 degrees. High beam up to 1800 Lumen. Low beam up to 1200 Lumen. The high beam is up to 1800 Lumens. Incredibly bright. Operates 5 to 30 Volts which means it will work at 6 volts or 30 volts. If you generator puts out higher voltage than 6 volts this light will work up to 30 volts. The bulb will work either AC or DC, meaning non polarized. Works either positive ground or negative ground. There are two contacts on the bottom one for low beam and one for high beam. This bulb is the perfect upgrade for vehicles, motorcycles and scooters. Available in 6000K to 6500K and Warm White 2700K to 3300K. Load equalizers may be required, if the bulb will not switch from low beam to high beam or if the bulb flickers when installed. Please install led light load equalizers to fix the problem product code 65832.

This headlight semi sealed housing is DOT approved. The lens color is clear. The head light housing accepts H4 P43T base headlights. You can use halogen, xenon, hid or led head bulbs as long as they are P43T base. Since these assemblies are DOT approved they are designed for driving in United States on the right hand side of the road RHD. The dimensions are 5" by 7" 200mm. The head light assemblies are easy to install usually remove 3 to 4 screws remove old glass or plastic headlight housing and insert new headlight housing and your new bulbs. These headlight housings work great for vintage and classic vehicles such as 6 volt or 12 volt positive or negative ground. Please check the warranty at the bottom of the page. The housing comes with a T10 5 Watt parking bulb that you can use for your parking light if needed. You can also upgrade this bulb from incandescent to led for the reliability of led lighting.

LED Headlight 6V BA15S male base single contact bayonets parallel. Up to 900 Lumen output. There are 16 forward firing 5730 smd led and 44 side firing smd leds. The leds are optically aligned filaments for optimum light output using your lens and light fixture. The bulb is dimmable so with your older vintage and classic cars you do not have to worry that you lights will flicker when you get low voltage, the headlight will slowly dim as your car battery or generator is putting out less voltage. This led lamp outputs up to 900 Lumens, or 60 MSCP to 70 CP candle power. The base is ba15s with bayonets parallel to each other and one contact on the bottom. You can use this bulb in 6 volt positive ground or 6 volt negative ground classic and vintage cars. Available in White 6000K and Warm White 3000K. Up to 340 forward firing Lumens and 560 side firing Lumens.

P43t LED Headlight 6 Volt. THis is a h4 male base dual filament headlight. Up to 900 Lumen output or 60 to 70 CP candle power. This bulb is dim-able so as your voltage in your old system is not putting out 6 volts these headlamps will still stay on dimmer. The life is long up to 30,000 hours. CE and Rohs listed. The side firing leds are optically aligned with your reflector for maximum light output out of your lens. The light comes in two colors white 6000K and warm white 3000K. The led lamp is designed to to be smaller than your current light bulb so you do not have to worry about installation issues. There are 16 forward firing and 44 side firing 5730 smd leds. Each 5730 smd can output up to 1/2 watt of power. Since these led bulbs are not polarity sensitive they will work in both positive ground and negative ground. Extend warranty, please see detail page for more information.

Headlight bulb 6 Volt Positive Ground or Negative Ground. BA15S base. Up to 700 Lumen, 55 CP. Single filament design. Designed for reflector headlights since most of the leds are side firing directly into the reflector. The bulb has some forward firing leds to make it brighter. This LED bulb is designed for early vintage Ford Model T and Ford Model A. Long life up to 30,000 hours. The M.O.L. is 1.962" and the diameter is .741". Plug and play remove the old incandescent bulb and replace with LED bulb. The LED uses less power than a incandescent bulb so it is easier on the wiring of the older vehicles. The bulb comes in White 6000K and Warm white 3000 K. The Warm White simulates the original color of a incandescent light bulb. How ever the Warm White is about 5% less output than the 6000 K bulb. CE and Rohs certified.

P15D-25-1 LED Headlight 6 Volt. Up to 900 Lumen or 60 to 70 CP candle power for high beam. Up to 400 Lumens for low beam or 30-40 CP. Available in white 6000K and warm white 3000K. The bulb is dimmable so you do not have to worry about the headlight fail when voltage drops below 6v. This bulb is optically aligned so you will get the maximum light output at your lens. Long-life up to 30,000 hours. Please see warranty for extended warranty details. This led lamp shape fits inside the outline of the existing light bulb so will be an easy installation. The bulb has 60 5730 SMD. There are 16 forward firing and 44 side firing leds. Illuminate directly in front of you with forward-firing chips and the side-firing will reflect light into the reflectors. Since these led bulbs are not polarity sensitive they operate in both positive ground and negative ground systems. This bulb can operate AC or DC.

159 LED Bulb works 6 volt positive or Negative Ground 159 T10 wedge. Great for old vehicles that were built or constructed before world war II. These older vehicles and motorcycles have a 6v positive chassis or 6v negative chassis. This T10 miniature bulb glass wedge will work in these old classic, vintage cars. The T10 rated voltage is 6 volts. Up to 30 Lumen side firing and 70 Lumen forward firing or 5.5 CP candle power for forward firing and 3.3 CP for side firing. Up to 1 Watt at 6 volts. Comparable to a 8 to 10 watt incandescent bulb. This led bulb fits arcade games, pinball machines and amusement rides that require 6 volt ac mini T10 wedge. This bulb also replaces 6V, 6.3V or 6.8V. Since this bulb is non polarity it can be used in 6 volt landscape lighting. This led bulb is a great replacement for glass wedge incandescent bulb. This bulb is T3-1/4, T3.25 shape meaning tubular and 3-1/4 wide.

Use one load equalizer for each led bulb in your turn signal circuit. Since this heavy duty load equalizer runs cooler it last longer. Stops hyper flashing and fixes CAN bus errors. Operates 6 Volt or 12 Volt positive ground or negative ground. The wire is 14 AWG high temperature. Comes with two insulation displacement connectors "IDC". Please do not cut your vehicle or motorcycle wires, just crimp the IDC on to your existing wires so that the load equalizers are in parallel with the led bulbs. The resistor body material is made from anodize aluminum. The rated current is up to 4 Amps. Since the load equalizer is 50 Watt power dissipation it runs cooler. The led light equalizer will get hot to the touch so it is recommended to mount to a metal surface. The body has mounting holes so you can easily attach it to a metal surface. The operating temp is around 100 degrees Celsius.

Use only two 3 Ohm 50 Watt Load Equalizers for your vehicle for the left and right side. Stops led light hyper-flashing and fixes CAN bus errors. Operates 6 Volt or 12 Volt positive ground or negative ground. The load equalizer can handle up to 4 Amps either 6 Volt or 12 Volt positive ground or negative ground. Since the resistor body is larger it runs cooler so load equalizer will last longer. The wire is 18 AWG high temperature resistant wires. Comes with two insulation displacement connectors so you can crimp these on to your existing wiring. Please install in parallel and do you cut your vehicle wires. Since the 3 Ohm 50 Watt is designed to install on the left or right side you only use two load equalizers instead of four. The load equalizer body is made of anodized aluminum. Please make sure to mount to metal surface since the body of the load equalizer gets hot.

Fixes flashing headlights or headlights that will not change from low beam to high beam. Operates 6 Volt or 12 Volt positive ground or negative ground. This heavy duty led headlight load equalizer operates cooler so it last longer. Rated at 4 Amps. Body is anodized aluminum. Comes with two insulation displacement connectors "IDC". Please crimp on to your existing wiring in parallel with the low beam on both your headlights. No need to cut your wiring harnesses when using the insulation displacement crimps. To test once installed the load equalizer should get warm or hot to the touch when you headlights on are low beam. The load equalizers come with 14 AWG heat resistant wiring. Please mount to a metal surface to help the load equalizer stay cooler. No need to purchase expensive and complicated harnesses when using these load equalizers. The wire length is about 4.5".

Converts your 6 Volt vehicle to be able to power 12 Volt accessories. Powers anything that is 4 Amps @ 12 Volt. The ballast has enough power in a small size. The input is 8 Amps @ 6 Volt input and the output is 4 amps @ 12 Volt. Works on both 6 Volt negative ground and 6 Volt positive ground cars, trucks, tractors and motorcycles. Long warranty please set page details for further warranty information. Easy to connect for (DIY) do it yourself retrofit. The ballast is water proof and is a non-isolated design. Please connect the ground and input 6 volt signal to the input side of the ballast the red and black wires. Please connect the output to a 12 Volt device using the yellow and black wires. With this ballast you can have DVD, Bluetooth, WIFI, USB port in your vintage and classic vehicles designed and built before World War II.

17" LED Third brake light for antique vehicles has dual filament. DOT lens. Available in Red and Yellow/Amber. This third brake light is for 6 volt vintage and classic vehicles, cars, trucks and motorcycles. Uses approximately up to 720mA@6.8 Volts for the brake light and uses up to 88mA@6.8 Volts for taillight. The brake light is up to 4.9 watts @ 6.8 Volts for brake light and the tail light is up to .59 Watts. Comparable up to a 40 to 45 Watt incandescent bulb. This third brake light will work either positive ground or negative ground. Operates from 3.2 Volts to 7.8 Volts non polarity. Works with either positive ground or negative ground. Has two recessed mounting holes that are .165" diameter so you can mount this on the surface. The hole to hole spacing is 16.14". If mounting to glass you would need to use some double sided tape or fabricate some kind of mounting bracket to use on glass.

1154 led bulb for 6 Volt. The led bulb works for both positive ground chassis or negative ground chassis. 1154 LED bulb is a 6v led bulb. Up to 320 Lumen for brake light and up to 240 Lumen for tail light. This bulb is same as 1154 bulb that has two brightness levels or two filaments one is for the tail light and the other is for the brake light. This bulb works great for non polarity 6 volt positive or negative ground. The LED bulb is small in size so it fits in G18 and S8/S25 bulb size applications. Made with the highest quality Samsung 5730 SMD led chips. Operates voltage up to 7.4 Volts. Voltage higher than 7.8 Volts will damage this bulb and voids warranty. The white 6000K bulb starts to light at at 3.5 Volts. This bulb will work the same as a incandescent bulb without the power drain or the filament breaking. Uses about 290mA @ 6.8 Volt for brake light and 90mA @ 6.8 Volt for taillight.

1158 LED Bulb operates in Positive Chassis ground or Negative Chassis ground vehicles, trucks and motorcycles. Special design for older cars. 1158 with a BA15D Bayonet base and has two brightness levels. The life is up to 30,000 hours. Available in white 6000 Kelvin, warm white 3000 Kelvin, Red 625 nm Green 526 nm, Blue 464 nm& Yellow 594 nm. Available 1158 BA15D. Great bulb for tight fit, this small high power led is great for all applications, very bright 320 lumen or 25 CP Candle Power output for brake light and 260 Lumen or 20 CP Candle Power for taillight. The lamp illuminates in 360 degrees. This bulb will operate in classic old cars with positive chassis or negative chassis car or bike, low voltage. Comparable to a 25 watt incandescent, very small fits it tight bulb locations. CE and Rohs listed. Works good for navigation lights for its small profile, operates both AC or DC.

Headlight bulb 6 Volt Positive Ground or 6 Volt Negative Ground. 6V AC or DC. Up to 650 Lumen high beam and up to 510 Lumen for low beam. This headlight bulb is up to 50 candle power CP for high beam. Up to 40 candle power CP for low beam. Dual filament design. Designed for reflector headlights since most of the leds are side firing directly into the reflector. The bulb has some forward firing leds to make it brighter. This LED bulb is designed for early vintage Ford Model T headlight and Ford Model A headlight. Long life up to 30,000 hours. Plug and play remove the old incandescent bulb and replace with LED bulb. The LED uses less power than a incandescent bulb so it is easier on the wiring of the older vehicles. This headlight bulb uses approximately .112 Amp @ 6.9 volts for low beam. This led headlamp bulb uses around .490 amp @ 6.9 volts for hi beam. The bulb comes in White 6000K and Warm white 3000K.

1129 led bulb will operate in both positive ground or negative ground 6 to 12 volt systems. Up to 24 CP regardless of voltage from 6 to 12. Up to 330 Lumen output. G18 S25 2.6 Watt bulb. Has 6 forward firing and 7 side firing LEDs. Each 5730 SMD LED is capable up to 1/2 Watt of power. Each 5730 LED can output up to 50 Lumens. The LED is not powered to full power so it can operate cooler so the SMD will last longer. The life is up to 30,000 hours. Since this led light bulb has 360 degree viewing angle up to 320 Lumen output for forward firing. Up to 350 Lumen output for side firing. Available in white 6000 Kelvin, warm white 3000 Kelvin, Red 625 nm Green 526 nm, Blue 464 nm& Yellow 594 nm. Available 1156 BA15S. Great bulb for tight fit, this small high power led is great for all applications. Will operate in classic old vintage antique cars positive earth, trucks or motorcycles 6 volt low voltage.

1142 LED Miniature BA15D S8 shape. Operates positive chassis or negative chassis 6 to 12 Volts. BA15D DC Bayonet 2.6 Watt L.E.D. bulb. Has 6 forward firing and 7 side firing LED's. Up to 30 CP. The LED bulb has a single filament brightness. This bulb will operate in a non polarity 6 volt systems positive chassis or negative chassis. The life is up to 30,000 hours. Available in white 6000 Kelvin, warm white 3000 Kelvin, Red 625 nm Green 526 nm, Blue 464 nm& Yellow 594 nm. Available BA15D. Please see 78865 for BA15S or 1156. Great bulb for tight fit, this small high power led is great for all applications, very bright 260 Lumen output in 360 degree illumination. This bulb will operate in vintage and classic old cars with positive grounds or positive chassis car or bike, low voltage. Comparable to a 20 watt incandescent, very small fits it tight bulb locations. CE and Rohs listed.

6V AC or DC. Use in positive ground or negative ground. 18 forward firing LEDs and 6 side firing LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat, virtually unbreakable. Up to 16 CP candle power output. Available in super white, red, yellow, green and blue. 6 VDC/ VAC. Approximate size is 1.57in x 1.03in. The max voltage is 8 volts. This 6 Volt bulb is designed for vintage vehicles and motorcycles for both negative ground chassis from post World War II and positive chassis from pre World War II. This product works when you apply 0 to the base and 6 Volts to the tip or if you apply 6 Volt to the base and ground to the tip the LED will light. This product will work both 6 Volt A.C. and 6 Volt D.C/A.C. applications. 1156 & 1157 bases. BA15S or BAY15d. Uses 1.8 watts, 15 watt incandescent equivalent, Up to 200 Lumen output.

81 LED Bulb 6 Volt Positive Chassis or Negative Chassis Miniature bulb. This bulb will work on AC or DC voltage. The maximum bulb length is 1.24 inches and the maximum diameter is is .75 inches. This will fit the small size of a #81 light bulb. BA15S single contact. G6 single contact bayonet LED. C-6, C-2R filament design compatible, single filament Uses only 1 Watt at 6 volts. Uses very low power. The profile is very small to match the profile of the #63 bulb. The light output is up to 90 Lumens the #63 bulb has a rated output of 3 candle power CP, the LED is up to 6 candle power so about twice as bright as stock light bulb. This bulb is available in White 6000K, Warm White 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Long life up to 30,000 hours.

Third brake light for 6 volt positive ground or negative ground vehicles. Available in Red and Yellow/Amber. Up to 320 Lumen output for the brake light and up to 250 Lumen output for the taillight. Made with 50 quantity 3030 high output led chip's. The black wire is ground, the white wire or yellow wire is for taillight or running light. The red wire is for brake light. If you do not want to use the taillight please just leave the white wire not connected. The length is 3" long and 3/8" wide. The flexible strip is rigid. The third brake light has some water resistant materials. Uses 113mA@6V for the taillight and 220mA@6V for brake light. The approximate power consumption is up to 1.2 Watts for brake light and up to .8 Watts for tail light. Comparable to a 10-15 Watt incandescent bulb.

1154 Miniature LED Bulb 6 Volt. This lamp will operate either Positive Ground or Negative Ground. BAY15D dual contact offset indexed bayonet LED. Dual filament. The #1154 has both a tail light and a brake light. There are two contacts on the bottom. One contact is for taillight. One contact is for brake light. The base is 15mm diameter. The bayonets are offset. Uses up to 1 Watt at 6 volts. Approximately uses 166mA @ 6 Volts. Uses very low power. The profile is very small. The overall length is 1.25 inches and the diameter is .59 inches. The light output is up to 200 Lumens for brake and 150 Lumens for taillight. The bulb brake light has a rated output of up to 16 candle power CP. The taillight has a rated output of up 11 candle power CP. This bulb is available in White 6000K, Warm White 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Long life up to 30,000 hours.

The BA9S led bulb is designed to operate at 6 volt ac or dc for both positive ground and negative ground vehicles. Small outline to match the outline of a 51 bulb. .7 inches long by .46 inches wide at the plastic ring. The base is .39" wide. Up to 135 Lumen output. The led's are small 7020 smd so they are very low profile. The life is up to 30,000 hours. The bulb is comparable to a 4 to 10 watt halogen light bulb. The viewing angle of the 7020 LED's is 120 degrees. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow/Amber. CE and Rohs listed. These led's are 80% energy savings really helps the low power generator provide power. This led bulb is dim-able using a dimmer switch or variable voltage supply. These led light bulbs work great for instrument panels using the different colors. Since led's generate their own color no plastic colored caps or painted light bulbs needed.

1142 LED BA15D 6 Volt Positive Ground and 6 Volt Negative Ground. Up to 150 Lumen forward firing, up to 20 Lumen side firing. Available in warm white 3000K and White 6000K. Comparable to a 25 Watt halogen bulb. Approximate size is 1.57in x 1.03in. BA15D base has a single filament. The bayonets are parallel or even and two contacts on the bottom. The diameter of the base is 15 mm. 360 degree illumination excellent choice for reflectors and lens. Dimmable with a variable voltage supply such as your dashboard dimmer switch. This is a single filament led bulb. To apply power you connect ground the one contact and apply plus 6 Volt to the other contact. Comparable to a 15 to 25 Watt incandescent bulb. CE and Rohs.

1847 LED Miniature Bulb works for both 6V positive ground chassis or 6V negative ground chassis. The led bulb is non-polarity 6 Volt BA9S. Sub miniature bayonet. Up to 80 Lumens, about 40 forward firing and 40 Lumens side firing. Up to 3 CP candle power forward firing and up to 3 CP candle power side firing. This bulb is dim-able using a variable power supply such as the dashboard dimmer knob. Rated life up to 30,000 hours. Uses .09 Amps @ 6 Volts. Up to 1 watt LED power comparable to a 10 Watt incandescent bulb. Made with six 5630 SMD led chips. Overall length 1.097" and .47" diameter. T3 1/4 Tubular package. Great for vintage, classic, cars, trucks, tractors, scooters or motorcycles. Excellent replacement for pinball, arcade and amusement rides.

1158 Bulb 6V 24 LED. Works either 6 Volt positive or negative ground. Approximate size is 1.57in x 1.03in. Up to 180 Lumen output. Works great for older pre World War II vehicles. Available in White 6000K, Red, Green, Blue, Yellow. Dual filament BA15D base. If tail light comes on brighter than brake light must rotate the bulb 180 degrees. Comparable to a 20 to 25 Watt incandescent bulb. The base is BA15D which means there are two contacts on the bottom. The bayonets are parallel. If the tail light is brighter than the brake light please rotate the lamp 180 degree's. Uses around 1.8 watts. The Lumen output for low is up to 160 Lumens. The high is up to 210 Lumens. The low beam side firing is up to 40 Lumen. The low beam forward firing is up to 120 Lumens. The high beam side firing is up to 53 Lumen. The high beam forward firing is up to 110 Lumen.

Small outline to match the 55 Miniature bulb. .7 inches long by .46 inches wide at the plastic ring. The base diameter is .39". Up to 135 Lumen output forward firing or up to 10 CP candle power. The led's are small 3030 smd so they are very low profile. Each 3030 smd can output up to 130 Lumens. The BA9S base is designed to operate at 6 volt ac or dc for both positive ground and negative ground vehicles. The life is up to 30,000 hours. This led lamp is dimmable using a variable voltage supply such as a dashboard dimmer. The bulb is comparable to a 4 to 10 watt halogen light bulb. The viewing angle of the 3030 LED's is 120 degrees. Available in White 5500K to 6500K, Warm White 2700K-3300K, Red, Green, Blue and Yellow/Amber. CE and Rohs listed. This bulb uses 90% less energy great for old generators. Uses .079mA at 6.8 volts. Compatible with the following: GE 51 Mazda 55 55N 755

1482 LED Bulb E10 miniature screw base 6 Volt positive chassis or negative chassis. Since the E10 is no polarity or non polarity. The bulb low profile, long life up to 30,000 hours, low voltage. The bulb uses approximately 1 Watt at 6 Volts. Approximately 70 Lumen output. Single filament design. Long life. Low voltage for 6 volt only positive ground or negative ground applications. See product detail for warranty period. Available in white 6000k, warm white 3000k, red, green, blue and yellow. This led bulb is dim-able using a variable AC power such as the dimmer knob on the dashboard. Since this bulb is non polarity works great for pre world war II vehicles and motorcycles. Upgrade to this bulb for license, running, turn signal, interior for long life and low power. Since this bulb is non polarity you do not have to worry how the existing socket is wired since this bulb is non polarity.

82 LED Bulb. BA15D Base. 6 Volt Positive Ground or 6 Volt Negative Ground. Up to 200 Lumen output. Up to 15 Candle Power. The maximum length is 1.25 inches and the maximum diameter is .75 inches. Comparable to a 10 to 25 Watt incandescent bulb. The L.E.D. bulb C-6 filament design. Single Filament. Uses up to 2 Watts @ 6 Volts. The base is BA15D with even bayonets. The lamp only has one brightness level. The bulb is dim-able using variable voltage supply such as dashboard knob. Great for license plate, turn, tail, brake, dome, dashboard, instrument panel lamps. The LED color is created by the material of the LED so it looks real nice monochromatic. The available colors are White 6000K, Warm White 3000K, Red 626nm, Green 526nm, Blue 646nm and Yellow 594nm. The old light bulbs were painted. Very low profile to fit Ford Model A cowl light. Long life up to 30,000 hours.

Used with a LED Light to simulate that the original light bulb is installed. Easy to install. Keep away from plastic or painted surfaces, resistor gets very hot. Connect the load equalizer in parallel with the led light you are replacing. Includes 7" of 20 awg stranded Teflon wire. 2 wire crimps included. Use one 6 Ohm 25 Watt equalizer for each LED bulb, or use one 3 ohm for 2 led bulbs for each turn signal control side that you replace. For a 6 Ohm load equalizer you can attach up to 1 LED light per equalizer. For the 3 Ohm load equalizer you can attach up to 2 LED lights per equalizer. Load equalizer dimensions are 0.75 inches in length and 0.42 inches wide. No special tools needed just a pair of pliers. The connection is made using insulation displacement connectors. This load equalizer eliminator capacitor operates from 6 to 12 volt positive ground or negative ground.

p45t LED Headlight 6 volt. Up to 650 Lumen output or 60 CP. Dual filament high and low beam. Made with 5730 smd leds for long life. Rohs and CE listed. Designed for easy installation, just remove old headlight and insert new headlight. Works both 6 volt positive ground and 6 volt negative ground. Great for old classic and vintage automobiles, motorcycles and tractors. Available in white 6000K and warm white 3000K. Long life up to 30,000 hours. Comparable to a 45 to 55 watt incandescent bulb. The maximum overall length is 1.944 inches. The maximum diameter is .760 inches. The pin out as follows when looking at the connector from the rear. The left most contact is ground. The center contact is low beam. The right most connector is high beam. This lamp will fit a standard H4 HB2 9003 3 prong female Socket connector such as part number 34265.

Used with a LED Light to simulate that the original light bulb is installed. Easy to install. Keep away from plastic or painted surfaces, resistor gets very hot. Connect the load equalizer in parallel with the led lamp you are installing. Approximate 6" of 20 AWG stranded Teflon wire. 2 wire crimps included. Use one 6 Ohm equalizer for each LED bulb, or use one 3 ohm for 2 led bulbs for each turn signal control side that you replace. Use one 20 Ohm or 100 Ohm for each side marker. For a 6 Ohm load equalizer you can attach up to 1 LED light per equalizer. For the 3 Ohm load equalizer you can attach up to 2 LED lights per equalizer. Load equalizer dimensions are 0.75 inches in length and 0.42 inches wide. (3 ohm equalizer is slightly larger). No special tools needed just a pair of pliers. The connection is made using insulation displacement connectors.

BA15S LED Bulb works in positive or negative ground vehicles. Single filament lamp. Operates 6 volts non polarity. Super bright led lamp using the latest high power 3030 SMD led. Each 3030 SMD can emit up to 30 Lumen output. Up to 400 Lumen output. Up to 31 CP candle power. Uses up to 3 Watts. Super low profile to fit the small cowl lights, indicator, taillight. Viewing angle is 120 degrees. Comparable to a 25 to 30 watt halogen light bulb. Available in White 6000K, Warm White 3000K, Red 625 nm and Yellow Yellow 594 nm. Extremely long life up to 30,000 hours. Solid-state never have to worry about a broken filament with led lamps. Compatible with early vintage cars, trucks and motorcycles. Dimmable with a variable voltage supply such as your dashboard dimmer. Single Contact Bayonet where the bayonets are parallel to each other with one contact at the bottom. Compatible with the C6 Filament shape.

LED Headlight Load Equalizer works from 6 Volt to 12 Volt classic and vintage cars and motorcycles. Works either positive ground or negative ground. Please use a load equalizers for your low beam, one per side if your headlights are not working properly after installation. Sometimes after upgrading the older car electrical system does not recognize the new technology. Since led headlights use 80% less power, sometimes load equalizers are needed. Please connect the load equalizer in parallel with the low beam circuit. To connect parallel means one end of goes to the chassis and the other end connects to your low beam. Please use one per the left headlight and right side headlight. Included are insulation displacement crimps IDC. The IDC are easy to install using pliers and easy to remove. Recommended to install to the metal of the car to help dissipate the heat.

T19 P15D-25-1 base led headlight. Up to 600 Lumen output. Dual filament Low and high beam. Long life up to 30,000 hours. The leds are optically aligned for best led light output using your reflective fixture. Please always clean the fixture when installing led light bulb. Comparable a 25 to 35 Watt halogen or incandescent bulb. The base is T19 P15D-25-1 base. This bulb operates either AC or DC. Operates at 6 volts, higher voltage with cause this bulb to fail. The bulb can operate up to 7.0 volts. Works either positive chassis or negative chassis. The M.O.L. maximum overall length is 1.976" and the M.O.D. maximum overall diameter is .747" not including the base diameter. CE and Rohs. Compatible with: p15d-25-1 PX15d H6 h6m P15D Honda TL125 125S 250 C105T 110 CT70 90 Honda 1970 mini trail Honda vintage mini trail 10-527-84114-09-xx

1154 LED Bulb 6 Volt. BAY15D base 1154. 60 LED Light bulb. Very bright up to 950 Lumens brake light. Up to 750 Lumens taillight. Operates 6V positive ground or 6V negative ground. BAY15D base 2 contacts tail light and brake light. One bayonet offset higher than the other bayonet. Long life up to 30,000 hours. Comparable to a 35 to 55 watt halogen or incandescent lamp. CE and Rohs listed. The leds are optically aligned to the reflector for maximum led light output. Up to 70 CP candle power output. Dim-able with a variable voltage supply. The BAY15D base is 15mm diameter with one bayonet indexed and two contacts. The maximum overall length M.O.L. 1.944 inches. The maximum diameter is 1.058 inches. Please make sure this bulb will fit your fixture. Uses about 1 Amp @ 6.3 Volts.

1158 6 Volt LED Bulb for both positive and negative ground vehicles and motorcycles. Up to 400 Lumen output for high beam and 360 Lumen for low beam. This bulb uses BA15D base that has two contacts and two bayonets. The bulb has two filament design. If the bulb is dim and should be bright just remove and reinsert 180 degrees. Comparable to a 25 to 35 watt incandescent bulb. Viewing angle is 120 degrees. The led lamp is dim-able using a variable voltage supply. Since the bulb is dim-able works good in the vintage and classic vehicles that the voltage is not up to 6 volts due to old wires and connections. White 6000 K, Warm White 3000 K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Up to 31 candle power. Maximum overall length MOL is 1.944 inches. Maximum diameter is .741 inches. CE and Rohs listed. Please see bottom of detail page for extended warrant details. Up to 30,000 hours life.

1154 6 Volt non polarity BAY15D. The Lumen output for brake light is up to 220 Lumens. The Lumen output for taillight is up to 150 Lumens. The approximate is 0.740" diameter and 1.023" length. The bulb is dimmable. The max voltage is 7.5 volts. The minimum required voltage is 5 volts. Long life up to 30,000 hours. Uses up to 90% less energy than a incandescent bulb. Comparable to a 15 Watt to 25 Watt incandescent bulb. CE and Rohs. Available in red, green, blue, yellow, white 6000K and warm white 3000K. The white 6000K is about 5% brighter than the warm white. The diameter of the base is 15mm. The bayonets are offset. There are two contacts on the bottom. CE and Rohs.

BA15D LED Headlight 5 To 30 Volt Single Filament Non Polarized. Up to 1800 Lumens. 1142 Configuration meaning ground on one contact and 5 to 30V on the other contact. Up to 30,000 hours for long life. Great for older vehicles generators. Easy to install remove old bulb and install this lamp. Works either positive ground or negative ground. Body made of aluminum for long life. Available in 6000-6500 Kelvin. Great for 6 volt, 12 volt up to 30 volts. Load equalizers may be required, if the bulb will not switch from low beam to high beam or if the bulb flickers when installed. Please install led light load equalizers to fix the problem product code 65832. Full bright at any voltage from 5 Volts to 30 Volts. Uses approximately 1.4A @ 6 volts. Overall length is 2.52 inches. Width is 0.98 inches. Length of the body above the BA15D base is 1.77 inches. Compatible with: 1130

Headlight housing 7" round DOT compliant with T10 5 Watt parking bulb. This assembly allows you to install your own led, hid, xenon or halogen bulb. The assembly accepts P43T H4 headlight bulb. These DOT headlamp assemblies are designed for USA right hand traffic LHD. The headlight housing is made of plastic. The assembly is CE and Rohs listed. The headlight semi sealed housing assembly has a clear lens. This assembly works great for vintage and classic vehicles with older faded glass or plastic headlights. For 6 volt positive ground and 6 volt negative ground vehicles you can use our 6 volt led bulbs and upgrade you old vehicle to led lighting. Easy DIY just remove existing headlight assembly and install this semi sealed headlight assembly usually by 3 screws. This headlight works good for motorcycles, scooters and tractors that are old and either 6 or 12 positive and negative ground systems.

1142 LED Miniature Bulb for positive or negative vehicles. Up to 500 Lumen output. Single filament C-6 design. BA15D base has two contacts and the bayonets are parallel to each other. Long life up to 30,000 hours. These LEDs are optically aligned so that the leds output the maximum light to the reflector and lens. This bulb is dimmable using a variable voltage supply. Since the bulb is dim-able works good when the voltage is not a peak voltage of 6 volts and will stay lit dimmer as the voltage goes down. For old vintage and classic cars this is a simple D.I.Y. do it yourself job. Please disconnect power, remove old bulb and insert new bulb. Comparable to a 25 to 35 Watt incandescent light bulb. CE and Rohs listed. The color options are white 6000k, warm white 3000k, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Extended warranty, please see bottom of product detail page for warranty details.

63 LED Bulb. Operates 6 Volt for vintage cars, trucks and motorycles. The base is BA15S single contact. Single filament. Up to 240 Lumen output or up to 18 CP. The lamp has 8 3030 smd. Each 3030 smd can output up to 30 Lumens. Works positive ground and negative ground. Super low profile to fit sockets that have fingers. Amazing long-life up to 30,000 hours. Uses 90% less energy. CE and Rohs. The base is 15mm diameter with two bayonets same height. Available in white 6000k, warm white 3000k, Red 625nm, Yellow 594nm, Green 526nm and Blue 464nm. Great for license plate lights. The viewing angle is 120 degrees. This bulb is dimmable using a variable voltage such as your dashboard dimmer. Upgrade your old lamp to a new super bright led. Your generator/alternator will be happy 90% less energy used. The shape is G6.3.0 MSCP. The filament design is compatible with C-6.

Flasher LED 6 Volt Positive Ground 3 Terminal for 6 Volt positive chassis. LED flasher for vintage and classic cars and motorcycles. This flasher is LED compatible so you can use led's or incandescent bulbs or a combination of both for the turn signal bulbs. The Pilot light bulb can be either incandescent or led. The flasher creates real clicking sounds like an old flasher. The flasher duty cycle is from 30% to 70%. The flasher rated load can handle up to 6 bulbs or 120 watts. The operating temperature -25F to +140F. The lamp rating should be from .1 Amp to 20 Amps. The rated voltage is from 5 to 8 volts can operate up to 8 volts. Voltage drop is rated at 500mv. The flasher will fit a standard 3 Pin female relay flasher socket. The shell is made of plastic for rugged long life. The flasher is self adjusting lamp amperage draw from .1 Amp to 20 Amps.

1158 Miniature LED Bulb operates 6V positive or negative ground vehicles. Up to 200 Lumen output for brake and 150 Lumen output for taillight. Long life up to 30,000 hours. Dual filament one filament for low beam and one filament for hi beam. BA15D base has two contacts and the bayonets are parallel to each other. This bulb is dim-able using a variable voltage supply. Since dim-able works great in vintage and classic vehicles that the electrical system is not full voltage. White 6000 K, Warm White 3000 K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. The M.O.L. is 1.25". The diameter is .59".

BA15D 6 Volt 60 SMD 5730 Single Filament Reduced Profile. This bulb operates 6v positive ground or 6V negative ground. Up to 900 Lumen output. Up to 340 forward firing Lumens and 560 side firing Lumens. Long life up to 30,000 hours. Made with total 60 leds, 44 side firing and 16 forward firing. This lamp is a single filament bulb. The base has even bayonets and two contacts on the bottom. This bulb is only designed for 6 volt vintage vehicles, motorcycles and scooters. Please make sure you voltage is regulated to 6 volts. The light bulb can be dimmed with a variable voltage supply if needed. The leds are aligned to be the optimum height for maximum light output using a reflector and lens. Available in White 6000K, Warm White 3000K, Red and Yellow. Maximum overall length is 1.694". The maximum diameter is 1.058". These lights led are solid state for low power and super long life.

H4 P43t base 6 Volt LED headlight for vintage vehicles and classic motorcycles. This led is designed for 6 volt motorcycle headlights. Works either AC or DC voltage. Very bright. Dual high and low beam. Up to 750 Lumen output. Comparable to a 50 - 75 Watt incandescent bulb. Made with the latest smd leds 5730. The profile of the led fits inside of a normal light bulb so you know it will fit your application. Operates either 6v positive ground or 6v negative ground. Up to 650 Lumens for high beam and up to 510 Lumens for low beam. This headlight bulb is up to 50 candle power CP for high beam. Up to 40 candle power CP for low beam. Long life up to 30,000 hours. This bulb uses approximately .490 amp @ 6.9 volts for hi beam. The bulb comes in White 6000K and Warm white 3000K. The Warm White simulates the original color of a incandescent light bulb.

6 Volt Festoon works with Positive Ground or Negative Ground. Up to 2 Watts of LED power. This festoon has 150 to 200 Lumen output. The led's are designed so that light lights in 180 degrees. This festoon is great for vintage, classic and antique cars, trucks and motorcycles. Vehicles made before World War II have a 6 volt positive chassis or 6 volt negative chassis. Since these LED's are AC non polarity they work great in these old vehicles. Long life up to 30,000 hours or longer. Available in White 6000K and Warm White 3000K. Comparable to a 15 to 20 Watt glass festoon incandescent light bulb. This festoon works great for pinball machines that are 6 volt AC systems. Certain amusement games and rides use 6 volt AC festoon so these are the perfect replacement. Long warranty please see warranty length on this detail page. The festoon viewing angle is around 240 degrees.

Festoon 6 volt for Positive Ground and Negative Ground vehicles. Up to 200 Lumen output. Long life up to 30,000 hours. Works non polarity AC or DC. Made with 6 5730 SMD high power leds. Available in White 6000 Kelvin and Warm White 3000 Kelvin. Vehicles and motorcycles made before World War II are positive chassis and this led bulb works perfectly. This led bulb is comparable to a 15 to 20 Watt incandescent glass festoon. The end caps are plated for rugged long life connection. Easy to install just remove the old festoon and insert the new led festoon plug & play. Since the new led festoon is non polarity you do not have to worry which way to install the bulb. Great replacement for 6 volt version of: 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 ED3022 DE3175 DE3425 De44101284 6450 This is a perfect replacement for glove box and console lighting upgrades.

6 volt festoon positive chassis or negative chassis non polarity. Up to 200 Lumen output. 1 1/4 length. Uses only 2 Watts, comparable to a 15 to 20 Watt glass festoon incandescent bulb. Since it is non polarity just insert into the festoon socket. Long life up to 30, 000 hours. Available in White 6000K and Wam White 3000K. The festoon end caps are rugged for secure electrical connection. Since the bulb is LED you do not have to worry about the filament breaking or the glass breaking. Great for arcade games and pinball machines. Since the festoon illuminates 180 degrees works great to illuminate the 180 degree viewing angle. The Warm White is closes color to a incandescence light bulb. The festoon has 6 chip high power 5730 SMD LED's. The diameter is .41 inches. Replaces 6 volt version of 3021 3022 3175 6428 6430 30922 De3425 C5W. The light is very clean and vivid.

p45t led headlight. Operates 6 volt positive ground or 6 volt negative ground. Up to 900 Lumen output or 70 CP for high beam. Up to 600 Lumen output for low beam. Available in warm white 3000k and white 6000k. Long life up to 30,000 hours. Since led's are solid state you do not have to worry about a broken filament or glass. CE and Rohs listed. Dual beam low and high beam. Works great for old vehicles made before World War II such as Ford Model A's and T. Easy DIY replacement just remove old incandescent and replace with new led bulb. Since led's use up to 90% less energy they really help the old generators and alternators with such a reduced load. Comparable to a 55 to 65 Watt incandescent bulb. The maximum diameter is 1.058" inches. The maximum overall length is 1.944 inches. Fits standard connector such as part number 34265. The pin out looking from the back is: Left side contact is ground.

H3 LED Bulb 8 Volt Positive ground or Negative Ground. Has a PK22s base. Up to 400 Lumen output. Long life up to 30,000 hours. Fits H3 sockets. Dim-able. Great for vintage automobiles and motorcycles. Solid state do not have to worry about broken filaments. Comparable to a 45 Watt incandescent bulb. Works great in old vintage 8 Volt to 9 Volt Fords. Available in White 6000K and Warm White 3000K. CE and Rohs. Comparable to a 35 to 45 Watt incandescent. CE and Rohs. The thickness is approximately 0.2". The dimension from the decking to the top of the bulb is 1.5". The overall length is 1.89" and the diameter of the decking is 0.86". The width of the bulb is 0.45".

BA15S LED Bulb works in positive or negative ground vehicles. Single filament lamp. Operates 8 volts non polarity. Super bright led lamp using the latest high power 3030 SMD led. Each 3030 SMD can emit up to 30 Lumen output. Up to 400 Lumen output. Up to 31 CP candle power. Super low profile to fit the small cowl lights, indicator, taillight. Viewing angle is 120 degrees. Comparable to a 25 to 30 watt halogen light bulb. Available in White 6000K, Warm White 3000K, Red 625 nm and Yellow Yellow 594 nm. Extremely long life up to 30,000 hours. Compatible with early vintage cars, trucks and motorcycles. Dimmable with a variable voltage supply such as your dashboard dimmer. Single Contact Bayonet where the bayonets are parallel to each other with one contact at the bottom. Compatible with the C6 Filament shape. The maximum overall length M.O.L. is .888 inches. The maximum bulb diameter is .748 inches.

BA15D 1158 6 Volt 60 SMD 5730 Dual Filament Reduced Profile. This bulb operates 6v positive ground or 6V negative ground. Up to 900 Lumen output for brake light and up to 500 Lumens for tail light. Up to 72 candle power CP for brake light and up to Up to 40 candle power for taillight. 340 forward firing Lumens and 560 side firing Lumens. Long life up to 30,000 hours. Made with total 60 leds, 44 side firing and 16 forward firing. This lamp is a two filament bulb. The base has even bayonets and two contact on the bottom, BA15D. This bulb is only designed for 6 volt vintage vehicles, motorcycles and scooters. Please make sure you voltage is regulated to 6 volts. The light bulb can be dimmed with a variable voltage supply if needed. The leds are aligned to be the optimum height for maximum light output using a reflector and lens. Available in White 6000K, Warm White 3000K, Red and Yellow.

1154 Bulb LED BAY15D Base 8 Volt 2.6 Watt. Works either negative ground or positive ground. Long life up to 30,000 hours. Uses only 2.6 Watts. Comparable to a 25 Watt halogen bulb. Has dual filament low beam and high beam. The bayonets are offset. The base has 2 contacts. The base diameter is 15mm. The MOL is 1.47". The MOD is .78". Available in White 6000, Warm White 3000K, Red, Green, Blue and Yellow. CE and Rohs. Up to 320 Lumen for brake light and 240 Lumen for tail light. This bulb is dim-able using a variable voltage supply. Use load equalizer per each led bulb that used in a turn signal circuit. Please use our solid state flasher with load equalizers. Works from 6 Volts up to 10 Volts. CE and Rohs.

H3 LED Bulb 6 Volt Positive or Negative Ground. Has a PK22s base. Fits H3 sockets. Operates 6 Volt Positive ground or negative Ground. Dim-able. Up to 200 Lumen output. Made with no breakable parts completely solid state. Available in White 6000K and Warm White 3000K. Comparable to a 40W to 50W incandescent bulb. The maximum overall length is 1.875" that is from the top to bottom of the bulb. The width of the bulb not including round flange is .453". The round flange maximum diameter is .866". The thickness is approximately 0.2". The dimension from the top of the decking to the top of the bulb is approximately 1.5" The CE and Rohs.

This universal led flasher will work positive ground vehicles, motorcycles and scooters. Operates from 6 to 15 Volts. Included are 7" of wire and quick disconnect crimps for easy installation. Flashes 60 times a minute. The load is from .5 Watt up to 20 Watt for led bulbs only. Please see diagram. CE and Rohs.

P36D base 5 to 30 volt positive ground or negative ground. Made with 16 2525 leds. Made with aluminum to keep the leds cooler so they last longer. This bulb is non polarized. Up to 1800 Lumen output for high beam up to 1200 Lumen output for low beam. Uses only 1.4 Amps high beam and .8 Amps for low beam. Long life up to 30,000 hours. Easy to replace just remove old bulb and insert new led bulb. CE and Rohs listed. Comparable to a 55W to 65W halogen bulb. This retrofit take around 1 minute to change the the old bulb. Dimensions are overall length is 2.52 inches. The width is 0.98 inches. Load equalizers may be required, if the bulb will not switch from low beam to high beam or if the bulb flickers when installed. Please install led light load equalizers to fix the problem product code 65832. Available in 6000K to 6500K. Compatible with: 312 30/24W 6 VOLT PRE-FOCUS Lucas 446, 414, 370, AND 312

H4 P43T led headlight bulb, works for both positive ground and negative ground vintage and classic vehicles, cars, trucks, motorcycles and scooters. 1:1 LED headlamps. These lamps are 1:1 plug and play lamps. They have the same clear cut-off line beam patterns as the original bulbs do, but much brighter and more compacted. The lamps are made with 8-chips high power 3570 LED's. Uses approximately 1.47A@8V for both low beam and high beam. The real output reaches up to 1800 Lumens per headlight bulb. Up to 144 CP candle power per led bulb. Comparable to a 55 to 65 Watt incandescent bulb. These CSP led's are very close to the original filament size for the best conversion to led. The mini-inside fan runs very differently from the ones in the market. They are rare to fail! And even if by any chance the fan fails, the lamp will work the same. Classic vehicle and heavy truck lighting area.

Third brake light for 6 Volt positive ground or negative ground vehicles, motorcycles or scooters. The LED third brake light has both taillight and brake light dual filament. The third brake light is 9" long and 3/8" wide. Great for older classic and vintage cars, trucks and motorcycles. The led third brake light has 3 wires, black if for ground positive or negative ground, yellow or white for taillight and red for brake light. The wire is 22 AWG gauge stranded. The wire is about 3.5" long. The light is flexible so it can be mounted on a curved or flat surface. Since some old vintage and classic cars have only one brake light this can be the second or third led brake light. Available in Red 625nm. There are 14 5050 led's, each led outputs about 22 Lumens for up to 308 Lumen output. The viewing angle is 120 degrees. .220A@6V for brake light and .077A@6V for taillight.

BAY15D LED Headlight 5 to 30 Volts. Non Polarity. Dual Filament. High beam up to 1800 Lumens. Low beam up to 1100 Lumens. Uses approximately .8 Amp for low beam. For high beam around 1.5 Amp. Made of aircraft aluminium to help keep the leds cool so the last longer. The base is 15 mm diameter. One bayonet is offset BAY15D base. There are two contacts on the bottom for low and high beam. Operates from 5 to 30 Volts which works good for older Fords that are 8 Volt. Helps your generator or alternator by using 80% less power than a incandescent or halogen bulb. Comparable to a 55 Watt halogen for low beam and 65 Watt for high beam. Made with high power led for long life. Operates in a wide voltage constant current meaning that this lamp will draw the same amps for wide range from 5 to 30 Volts.

6 Volt LED Bulb Non Polarity T10 Wedge. Works either Positive ground or Negative Ground. For 6.3 Volt AC/DC non polarity vintage and classic vehicles and motorcycles, scooters. 120 degree viewing angle. Long life up to 30,000 hours. Available in White 6000K, Warm White 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Up to 50 Lumen output. Forward firing led's. Approximate dimensions 0.63" length and 0.44" max width, the wedge is dimension is 0.35" wide. Dimmable, comparable to a 4 to 9 Watt incandesce bulb. Fits a standard T10 wedge socket. Compatible with: T10 W5W 192 158 168 194 2825 555. CE and Rohs.

63 LED Bulb 8 to 9 Volt BA15S Base. Designed for 8 Volt Fords. Works both positive ground or negative ground. Up to 18 CP or 240 Lumen output. 120 degree viewing angle. Long life up to 30,000 hours. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow. Single Contact, Single Filament BA15S. The bayonets are even and has one contact and the bottom. The base diameter is 15mm. The bulb is made very low profile to work when used in old sockets that classic and vintage cars have. The bulb is dimmable. Comparable to a 25 Watt incandescent bulb. The shape is G6.3.0 MSCP. The filament design is compatible with C-6. This bulb is a true 63 compatible since the board is mounted inside the ba15s base. The overall length M.O.L. is .888 inches. The maximum bulb diameter is .590 inches. CE and Rohs listed. Compatible with: GM #142303 Mazda bulb GE 63 #1133 TS67

51 Miniature Bulb BA9S Base operates 8 to 9 Volt 3 SMD 7020 LED T3 1/4. Works either positive ground or negative ground. Great for motorcycles or 8 Volt Fords. Long life up to 30,000 hours. 120 viewing angle. Comparable to a 4 to 20 Watt incandescent bulb. CE and Rohs. .7 inches long by .46 inches wide. Up to 135 Lumen output. Outputs up to 10 CP forward firing. The led bulb is dimmable using a variable voltage supply such as a dashboard dimmer switch. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow/Amber. This bulb uses approximately 67mA@8Volts. The bulb only uses approximately a 1/2 Watt of power.

BA15S LED Headlight. This lamp has no polarity, non polarized or bi polar. The led headlight is designed for both positive ground or negative ground. BA15S base single contact. Super bright up to 1,200 Lumen. Headlight has aviation aluminum to keep the leds cool so they last longer. Wide voltage 5 to 30 volts AC or DC. The LED's are csp high power. The circuit board is super conducting aluminum. The headlight uses wide voltage and a constant current design. The leds are on both sides so the led light will project light into the housing. The base diameter is 15mm and has a single contact. The bayonets are the same height. Available in White 6000K to 6500k. Long life up to 30,000 hours. Comparable to a 45 to 55 Watt incandescent bulb. The current consumption is 800mA. The socket is made of copper for maximum conductivity. Dimensions are overall length is 2.52 inches.

BA15D LED Bulb 6 Volt. Up to 900 Lumen output. Up to 700 Lumen for low beam. Dual filament both a brake and taillight. BA15D 2 contact with parallel bayonets. 6 Volt Positive or negative ground vehicles, motorcycles and tractors. Since this bulb is dim-able using a variable voltage supply such as your dashboard dimmer switch. Works great if your vehicle has older wiring where all the volts do not make it. CE and Rohs listed. Comparable to a 35 to 55 watt incandescent light bulb. Viewing angle is 360 degrees. The Smd's are optically aligned with your reflector so you get maximum light output. Available in White 6000 K, Warm White 3000 K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. CE and Rohs listed. Long life up to 30,000 hours. The bulb is led so no more worries about broken filament or glass bulb. The maximum overall length M.O.L is 1.944". The maximum diameter is 1.05".

BA15S 1129 6 Volt 60 SMD 5730 Single Filament Reduced Profile. This bulb operates 6v positive ground or 6V negative ground. Up to 900 Lumen output. Up to 340 forward firing Lumens and 560 side firing Lumens. Long life up to 30,000 hours. Made with total 60 leds, 44 side firing and 16 forward firing. This lamp is a single filament bulb. The base has even bayonets and one contact on the bottom. This bulb is only designed for 6 volt vintage vehicles, motorcycles and scooters. Please make sure you voltage is regulated to 6 volts. The light bulb can be dimmed with a variable voltage supply if needed. The leds are aligned to be the optimum height for maximum light output using a reflector and lens. Available in White 6000K, Warm White 3000K, Red and Yellow. Maximum overall length is 1.694". The maximum diameter is 1.058". These lights led are solid state for low power and super long life.

1142 6 Volt LED Bulb. This lamp has 60 5730 smd leds. Up to 850 Lumen output single filament. The BA15D base has two contacts and the bayonets are parallel. Please apply ground to one contact and 6 Volts to the other contact. The leds are are optically aligned with the reflector for maximum led light output. 360 degree viewing angle. Long life up to 30,000 hours. Dim-able using a variable DC power supply such as your dashboard dimmer switch. Works in both positive ground and negative ground vehicles, tractors and trucks. The 1142 has a single filament, meaning this led is only on and off. CE and Rohs listed. Up to 70 CP candle power. Long warranty please see details below. The color options are white 6000k, warm white 3000k, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. The base is BA15D the diameter of the base is 15mm with two contacts. The overall length is 1.944 inches.

1158 LED Bulb BA15D Base 8 Volt 2.6 Watt G18. Dual filament both tail light and brake light. Up to 320 Lumens for brake light and 240 Lumens for taillight. Long life up to 30,000 hours. Works either positive ground or negative ground. The base has even bayonets. There are two contacts. The diameter is 15mm. Dim-able with variable voltage supply. Available in White 6000K, Warm White 3000K, Green, Blue, Red and Yellow. 8 Volts is designed for 8 Volt Fords. CE and Rohs.

Festoon LED Bulb. 28mm length or 1.1" long. Works 6 Volt positive ground or negative ground. Long life up to 30,000 hours. Up to 50 Lumen output. Available in White 6000K and Warm White 3000K. Dimmable with a variable voltage supply such as a dashboard dimmer switch. Viewing angle 120 degrees. Comparable to 9 to 21 Watt incandescent bulb. Compatible with Volkswagen, Semaphore bulb, VHD-N17-7261, N177261.

BAY15D 1154 6 Volt 60 SMD 5730 Dual Filament Reduced Profile. This bulb operates 6v positive ground or 6V negative ground. Up to 950 Lumen output for brake light and up to 750 Lumens for tail light. Long life up to 30,000 hours. Made with total 60 leds, 44 side firing and 16 forward firing. This lamp is a two filament bulb. The base has offset bayonets and two contact on the bottom. This bulb is only designed for 6 volt vintage vehicles, motorcycles and scooters. Please make sure you voltage is regulated to 6 volts. The light bulb can be dimmed with a variable voltage supply if needed. The leds are aligned to be the optimum height for maximum light output using a reflector and lens. Available in White 6000K, Warm White 3000K, Red and Yellow. Maximum overall length is 1.694". The maximum diameter is 1.058". These lights led are solid state for low power and super long life.

LED headlamp works either positive ground or negative ground. Wide voltage from 5 to 30 Volts AC or DC. Available White 6000K to 6500K or Warm White 2700K to 3300K. No polarity, Bi polarity, non polarized. Made with 16 2525 smd for super bright. The headlamp lights on both sides. Dual filament both a low and high beam. The low beam Lumen output is up to 1200 Lumens. The high beam is up to 1800 Lumens. Great for vintage and classic cars. Long life up to 30,000 hours. CE and Rohs certified. Made with aluminum to keep the led lamps cool so they can operate for a long life. The circuit board is constant current so the leds should not flicker. Available in White 6500k. Perfectly works with product 69854 is a 7" round semi-sealed housing and 68721 is a 5"x7" rectangle housing. Both these semi-sealed housings use the P43T bulb.

For positive ground or negative ground. 5 to 30 Volt wide voltage. Long life up to 30,000 hours. Made with 2525 LED's for long life. Dual filament up to 1200 Lumen low beam. Works both in a socket that is wired for a single filament and works in a ba15d socket that is wired for dual filament. Up to 1800 Lumen high beam. The base is BA15D the diameter is 15mm with two contacts on the bottom and parallel bayonets. Made with aviation aircraft aluminium to keep the leds cool for longer life. Available in White 5000-6000K and Warm White 3000K. Dimensions are overall length is 2.52 inches. The width is 0.98 inches. The length of the body above the BA15D base is 1.77 inches. The circuit board is super conducting aluminum for maximum power supplied the the leds. The led headlamp is a constant current device so the brightness will not fluctuate. CE and Rohs listed.

P36D 5 to 30 Volt positive ground or negative ground non polarized. Made with 2525 led's for long life up to 30,000 hours. High Lumens up to 1200 Lumens. Uses only .8 Amps. Works great for 6 volt vintage cars, motorcycles and tractors. The heat sink is made of aluminum to make the leds operate cooler so they are brighter and last longer. CE and Rohs listed. Comparable to a 45 to 55 Watt incandescent light bulb. Takes just minutes to install. Just remove the old bulb and insert the new led bulb. The base is P36D has one contact on the bottom and diameter of flange is 36mm. Dimensions are overall length is 2.52 inches. The width is 0.98 inches. Load equalizers may be required, if the bulb will not switch from low beam to high beam or if the bulb flickers when installed. Please install led light load equalizers to fix the problem product code 65832. Available in White 6000K to 6500K.

LED light isolator is used when the brake/turn light control module/switch asserts low signal for negative ground when not active or asserts high signal when not active for positive ground vehicles, trucks and motorcycles. This causes your taillights not to work. Works for 6 Volt, 12 Volt or 24 Volt systems. Works for either positive ground or negative ground vehicles. Isolator rated for 10 Amps. Each isolator can dissipate 60 watts @ 6V, 120 Watts@12V and 240 Watts@24V. To install isolator you must cut brake light wire and splice the isolator inline in the brake light circuit. The wires are stranded 18 AWG. Comes with two I.D.C. insulation displacement connectors. No soldering required using the crimps. The wire length is 5" each side for a total of 10" for both sides. The isolator diameter is approximately .4" diameter and .4" in length.

1158 LED Bulb BA15D Base 12 Volt 2.6 Watt G18. Operates either positive ground or negative ground. Taillight up to 240 Lumens, Brake light up to 320 Lumens. Available in White 6000K, Warm White 3000K, Red, Yellow, Green and Blue. Dim-able with variable voltage supply. The base bayonets are even with two contacts. The base diameter is 15mm. The MOL is 1.47", the MOD is .78". Long life up to 30,000 hours. CE and Rohs.

Very bright H1 led headlight bulb. Uses P14.5 base. Works both positive ground or negative ground. Up to 1400 Lumen output. Uses up to 16 Watts. Single filament lamp. Uses aluminum heat sink to keep led's cool so they last longer. Available in White 6000K or Warm White 3000K. Comparable up to 144 Watt incandescent bulb. This headlight bulb can work in 6 volt vehicles, trucks, motorcycles and scooters. Works also in 8 volt Fords. Sold as a pair. This bulb is not dimmable since it is wide voltage from 5 to 9 volts. CE and Rohs.

Operates 7 to 9 Volts positive ground or negative ground. Up to 135 Lumen output. Approximate size 0.7 inches long by .46 inches wide at the plastic ring while the base is .356" which is 9mm. 120 Degree viewing angle. Uses .079mA at 8.8 volts. Comparable to a 20 Watt incandescent. Long life up to 30,000 hours. Great for dashboard instruments. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow/Amber. The light is dim-able using a variable voltage supply such as your dashboard dimmer. This bulb uses 80% less energy than your incandescent bulb, great for old generators. CE and Rohs. Size is a T3 1/4.

5 to 30V positive ground or negative ground non polarity. P45t base, has a notch on the side not shown. Made with 16 Cree 2525 LEDs. Available in 6000K to 6500K. Dual filament the low beam Lumens up to 1200. The high beam Lumens up to 1800. Long life 30,000 hours. Made with aluminum for long life. Uses only 800mA. Uses around 9.6 Watts. Constant current the driver to reduce flicker. The base is P45t. This led bulb is for old vintage and classic cars, trucks, motorcycles, and scooters. Long-life up to 30,000 hours. 8 LEDs on each side for best illumination. When looking at the connect from the rear the ground is the left-most contact. The center contact is the low beam. The rightmost contact is the high beam. Please click on the manual to see the wiring diagram for this bulb. 4 smd chips will be lit for low beam both sides and all 8 smd chips both sides will be lit for high beam.

1129 miniature led bulb 60 smd. 6 Volt positive or negative ground. Very bright up to 900 Lumen output. The bulb is not polarity sensitive so you can use it either positive ground or negative ground chassis. The base is BA15S single contact with bayonets parallel. This bulb is dim-able using a variable voltage supply. Long life is up to 30,000 hours or longer. The viewing angle is 360 degrees. The led's are optically aligned with your reflector for maximum led light output. The bulb has 16 forward firing led's. The forward firing Lumens are up to 340 Lumens. The bulb has 44 side firing led's. The side firing Lumens are up to 560 Lumens. The maximum overall length is 1.944 inches. The maximum diameter is 1.058 inches. The base is BA15S 15mm standard base size with a single contact. Comparable to a C-6 single filament. The bulb is dim-able with a variable voltage supply such as your dashboard dimmer.

6V LED Headlight. Works 6V AC or 6V DC. 60 quantity 5730 smd leds. Optically filament aligned so you get maximum light output through your headlight fixture and lens. The headlight is dimmable using a variable voltage supply. Being dimmable helps out with the older vintage and classic vehicles voltage system and wiring is not 100%. There is a total of 16 forward firing and 44 side firing leds. Each 5730 uses up to 1/2 Watt of power. This bulb up to 950 Lumen or 70 MSCP for high beam. Low beam up to 500 Lumens or 40 CP for low beam. Compatible with C-6 filament designed light bulbs. Comparable to a 30 Watt to 55-56W Watt incandescent light bulb. This bulb works in both 6 volt negative ground and 6 volt positive ground vehicles, tractors and motorcycles. This lamp can operate 6 Volts and has both a low beam and a high beam filament. Long life up to 30,000 hours.

Converts from 12 Volt 4 Amp to 6 Volt 8 Amp. The features are 1. Synchronous rectification technology, the conversion efficiency more than 96%. 2. Internal resistance capacitor filter, withstand high temperature. 3. Almost no heat generated when operated. 4. Chip smart protection, anti-overheating, overcurrent protection. Use this to power your 6 volt powered devices from 12 Volts. Works both positive ground and negative ground vehicles, motorcycles and scooters. It is a good ideas also to put a power switch to turn off the device when not in use. It could be wired to your ignition line where power would be applied when the ignition switch is turned on. Operates from 10V to 35V input voltage. The output is regulated at .1V@6V. The output power is 48 Watts. The Transfer efficiency up to 96%. The Working temperature is -25?-85?. The converter has overheating protection at 150?. The no load current =0.35mA.

82 LED Bulb, single filament. Works either positive ground or negative ground. Bulb has 9 T5 LED's. Up to 200 Lumen output. The bulb has a rated output of 7 candle power CP. BA15D base. The diameter is 15mm and has two bayonets that are even. Single filament with two contacts. Single filament. The available color options are white 6000k, Red 625 nm, Yellow 594 nm. CE and Rohs. Some Warm White 3000K while inventory last. The overall length is 1.25 inches and the diameter is .59 inches. Comparable to a 10 Watt to 25 Watt incandescent bulb. Uses up to 1 Watt @ 6 Volts. Uses approximately 166mA @ 6 Volts. Dimmable with a variable voltage supply such as your dashboard dimmer switch.

#1154 6 Volt Positive or Negative Chassis vehicles, trucks and tractors. Up to 400 Lumen output. BAY15D base meaning two contact and the bayonets are offset. This is a two filament C-6 Design. Since there are two filament one if for tail light and one is for brake light or turn signal. The leds are optically aligned where the original filaments would be so the light output is maximized and not wasted. This bulb diameter is smaller than a normal #1157 and the length is the same so you should not have any issues installing the bulb. The bulb is available in white 6K, warm white 3K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Long warranty please see bottom of the page for more warranty information. This can be used for a 6 volt led brake light or running light. The M.O.L. is 1.962" and the diameter is 0.741". CE and Rohs. Compatible with: 1154 #1154

1129 6 Volt LED for positive or negative ground. Single filament, single contact SC C-6 S9. 30 quantity 5730 SMD LED's. Up to 600 Lumen. The LED are optically aligned to the original filament location. Since the led's are aligned they are able to output to the reflector and lens better light output. Comparable to a 25 to 35 Watt incandescent light bulb. The viewing angle is 120 degrees. The lamp is dimmable using a variable voltage source. Since the lights are dim-able they operate better when there is a low voltage condition. The bulbs are available in white 6000K, warm white 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. The bulbs are non polarity or not polarized so you can use them in sockets that are wired backwards such as RV's and boats. This bulb works great for your vintage or classic vehicle that you want to use led lights.

BA20D LED headlight 5 to 30 volt. The base is rotated 90 degrees. High beam up to 1800 Lumen. Low beam up to 1200 Lumen. The high beam is up to 1800 Lumens. Incredibly bright. Operates 5 to 30 Volts which means it will work at 6 volts or 30 volts. If you generator puts out higher voltage than 6 volts this light will work up to 30 volts. The bulb will work either AC or DC, meaning non polarized. Works either positive ground or negative ground. There are two contacts on the bottom one for low beam and one for high beam. This bulb is the perfect upgrade for vehicles, motorcycles and scooters. Available in 6000K to 6500K and Warm White 2700K to 3300K. Load equalizers may be required, if the bulb will not switch from low beam to high beam or if the bulb flickers when installed. Please install led light load equalizers to fix the problem product code 65832.

This headlight semi sealed housing is DOT approved. The lens color is clear. The head light housing accepts H4 P43T base headlights. You can use halogen, xenon, hid or led head bulbs as long as they are P43T base. Since these assemblies are DOT approved they are designed for driving in United States on the right hand side of the road RHD. The dimensions are 5" by 7" 200mm. The head light assemblies are easy to install usually remove 3 to 4 screws remove old glass or plastic headlight housing and insert new headlight housing and your new bulbs. These headlight housings work great for vintage and classic vehicles such as 6 volt or 12 volt positive or negative ground. Please check the warranty at the bottom of the page. The housing comes with a T10 5 Watt parking bulb that you can use for your parking light if needed. You can also upgrade this bulb from incandescent to led for the reliability of led lighting.

LED Headlight 6V BA15S male base single contact bayonets parallel. Up to 900 Lumen output. There are 16 forward firing 5730 smd led and 44 side firing smd leds. The leds are optically aligned filaments for optimum light output using your lens and light fixture. The bulb is dimmable so with your older vintage and classic cars you do not have to worry that you lights will flicker when you get low voltage, the headlight will slowly dim as your car battery or generator is putting out less voltage. This led lamp outputs up to 900 Lumens, or 60 MSCP to 70 CP candle power. The base is ba15s with bayonets parallel to each other and one contact on the bottom. You can use this bulb in 6 volt positive ground or 6 volt negative ground classic and vintage cars. Available in White 6000K and Warm White 3000K. Up to 340 forward firing Lumens and 560 side firing Lumens.

P43t LED Headlight 6 Volt. THis is a h4 male base dual filament headlight. Up to 900 Lumen output or 60 to 70 CP candle power. This bulb is dim-able so as your voltage in your old system is not putting out 6 volts these headlamps will still stay on dimmer. The life is long up to 30,000 hours. CE and Rohs listed. The side firing leds are optically aligned with your reflector for maximum light output out of your lens. The light comes in two colors white 6000K and warm white 3000K. The led lamp is designed to to be smaller than your current light bulb so you do not have to worry about installation issues. There are 16 forward firing and 44 side firing 5730 smd leds. Each 5730 smd can output up to 1/2 watt of power. Since these led bulbs are not polarity sensitive they will work in both positive ground and negative ground. Extend warranty, please see detail page for more information.

Headlight bulb 6 Volt Positive Ground or Negative Ground. BA15S base. Up to 700 Lumen, 55 CP. Single filament design. Designed for reflector headlights since most of the leds are side firing directly into the reflector. The bulb has some forward firing leds to make it brighter. This LED bulb is designed for early vintage Ford Model T and Ford Model A. Long life up to 30,000 hours. The M.O.L. is 1.962" and the diameter is .741". Plug and play remove the old incandescent bulb and replace with LED bulb. The LED uses less power than a incandescent bulb so it is easier on the wiring of the older vehicles. The bulb comes in White 6000K and Warm white 3000 K. The Warm White simulates the original color of a incandescent light bulb. How ever the Warm White is about 5% less output than the 6000 K bulb. CE and Rohs certified.

P15D-25-1 LED Headlight 6 Volt. Up to 900 Lumen or 60 to 70 CP candle power for high beam. Up to 400 Lumens for low beam or 30-40 CP. Available in white 6000K and warm white 3000K. The bulb is dimmable so you do not have to worry about the headlight fail when voltage drops below 6v. This bulb is optically aligned so you will get the maximum light output at your lens. Long-life up to 30,000 hours. Please see warranty for extended warranty details. This led lamp shape fits inside the outline of the existing light bulb so will be an easy installation. The bulb has 60 5730 SMD. There are 16 forward firing and 44 side firing leds. Illuminate directly in front of you with forward-firing chips and the side-firing will reflect light into the reflectors. Since these led bulbs are not polarity sensitive they operate in both positive ground and negative ground systems. This bulb can operate AC or DC.

159 LED Bulb works 6 volt positive or Negative Ground 159 T10 wedge. Great for old vehicles that were built or constructed before world war II. These older vehicles and motorcycles have a 6v positive chassis or 6v negative chassis. This T10 miniature bulb glass wedge will work in these old classic, vintage cars. The T10 rated voltage is 6 volts. Up to 30 Lumen side firing and 70 Lumen forward firing or 5.5 CP candle power for forward firing and 3.3 CP for side firing. Up to 1 Watt at 6 volts. Comparable to a 8 to 10 watt incandescent bulb. This led bulb fits arcade games, pinball machines and amusement rides that require 6 volt ac mini T10 wedge. This bulb also replaces 6V, 6.3V or 6.8V. Since this bulb is non polarity it can be used in 6 volt landscape lighting. This led bulb is a great replacement for glass wedge incandescent bulb. This bulb is T3-1/4, T3.25 shape meaning tubular and 3-1/4 wide.

1142 LED BA15D 6 Volt Positive Ground and 6 Volt Negative Ground. Up to 150 Lumen forward firing, up to 20 Lumen side firing. Available in warm white 3000K and White 6000K. Comparable to a 25 Watt halogen bulb. Approximate size is 1.57in x 1.03in. BA15D base has a single filament. The bayonets are parallel or even and two contacts on the bottom. The diameter of the base is 15 mm. 360 degree illumination excellent choice for reflectors and lens. Dimmable with a variable voltage supply such as your dashboard dimmer switch. This is a single filament led bulb. To apply power you connect ground the one contact and apply plus 6 Volt to the other contact. Comparable to a 15 to 25 Watt incandescent bulb. CE and Rohs.

1158 Bulb 6V 24 LED. Works either 6 Volt positive or negative ground. Approximate size is 1.57in x 1.03in. Up to 180 Lumen output. Works great for older pre World War II vehicles. Available in White 6000K, Red, Green, Blue, Yellow. Dual filament BA15D base. If tail light comes on brighter than brake light must rotate the bulb 180 degrees. Comparable to a 20 to 25 Watt incandescent bulb. The base is BA15D which means there are two contacts on the bottom. The bayonets are parallel. If the tail light is brighter than the brake light please rotate the lamp 180 degree's. Uses around 1.8 watts. The Lumen output for low is up to 160 Lumens. The high is up to 210 Lumens. The low beam side firing is up to 40 Lumen. The low beam forward firing is up to 120 Lumens. The high beam side firing is up to 53 Lumen. The high beam forward firing is up to 110 Lumen.

BA7S base end cap male. Made of copper material for good electrical connection. This BA7S is solder able. Use for automobile dashboard light bulbs. Great to replace old one of a kind BA7S bulb.

T7 BA7S LED Lamp. Very small BA7S male base. Operates 12 Volt DC only. This LED measures approximately 0.99 inches by .41 inches by 0.31 inches. Available in White 6000 Kelvin, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). This bulb has 5 3 chip 5050 SMT's. Long Life up to 30,000 hours. Full 360 degree viewing angle. Dim-able with a dimmer switch. Comparable to a 15 Watt incandescent bulb. CE and Rohs listed. Compatible with 1980 MGB.

3798 5 LED Bulb 6 Volt negative ground. This bulb dim-able using a variable voltage such as your dashboard dimmer. Uses about 1.5 Watts at 6 Volts. The Lumen output is about 40 Lumen side firing and 70 Lumen forward firing. Vehicles, tractors, trucks and motorcycles that were bulb pre world war II. The bulb is CE and Rohs listed. This 6v led bulb will fit all vehicles that require a BA7S bulb. This bulb is a available in White 6000K and Warm White 3000K. This BA7S will fit old dashboards, instrument panels, military, marine applications and other retrofit applications that require 6v T7 BA7S led bulb. T2 1/2 or T2.5 tubular bulb shape. Single filament design. Compatible with the following: #3798 #1262 LLB282 #4050

24 Volt D.C. BA9S Short Round LED Bulb. CE and Rohs listed. Long life up to 30,000 hours. Available in White 6000, Red(625nm), Blue(464nm) & Yellow(594nm). Approximate 7 lumen output, 120 degree viewing angle. Uses approximately 25mA @ 24V. Comparable to a 4 to 9 Watt incandescent. The base diameter is about 9mm. One product per package.

This automotive BA9S SMD 5050 3-Chip LED's. Each LED has 3 LED chips. Durable, shock and vibration proof, instant On/Off. Up to 50 Lumen output forward firing and 40 side firing Lumens. Uses only 1.5 Watts @ 12V. Comparable to a 12-15 watt incandescent bulb. Measures .45in wide and 1.17in from top to bottom. Available in super white, red, yellow and blue. .110 A @ 13.8V DC. Please note this product is polarity sensitive operates on negative ground chassis. Dim-able. Self ballast rated voltage from 8V to 15V. 360 degree viewing angle. Dim-able using a variable voltage supply such as a dashboard dimmer switch. Compatible with: 1953 Cessna 170 ba9s light bulbs.

182 Led Bulb short round. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue, ultra violet and rgb red/green/blue. 25 mA @ 13.8V DC 345 mW. Puts out approximately 7 Lumens. Operates 6 volt DC to 12 volt DC. This bulb can be dimmed using a dashboard dimming knob or a variable DC power supply. Comparable to a 4 to 9 Watt incandescent light bulb. Viewing angle 120 degrees. Compatible with: 1953 Cessna 170 ba9s light bulbs.

257 LED Bulb 6 LED. 6 LED's. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. 120 Degree Beam Width. Available in super white, warm white. red, yellow, green and blue. Uses 40 mA @ 13.8 VDC = .552 Watts. Comparable to a 3-4 watt incandescent bulb. Please see product detail for warranty period. Up to 42 Lumen output. Dimmable with a variable voltage supply such as a dashboard dimmer switch that varies its voltage. Compatible with: 1994 Land rover defender 1953 Cessna 170 ba9s light bulbs.

44 Led Bulb tall round. Up to 7 Lumen output. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 25 mA @ 13.8 VDC 345 mW. Approximate size 1.12 in (height) x .44 in (diameter). Miniature bayonet 10 mm diameter. Comparable to a 4 to 9 Watt incandescent light bulb. Dim-able with a variable voltage supply such as a dashboard dimming switch. 60 Degree viewing angle. Up to 30,000 hours. Operates from 6 to 12 Volts DC. CE and Rohs listed. Compatible with 1953 Cessna 170 ba9s light bulbs.

57 Led Bulb with 1 Ultra Bright LED. 1 Watt output. 12 VDC. Available in red, yellow, super white, green and blue. 10 watt equivalent. 0.5" diameter and 0.8" length. 1 Per package. Uses about 70mA for white. Fully dimmable with a variable power source. Up to 70 Lumen output. Dim-able with a dashboard dimming switch. Designed for negative ground chassis. Compatible with 1953 Cessna 170 ba9s light bulbs. BA9S #44 #53 #57 #182 #257 #363 #430 #615 #756 #1445 #1155 #1815 #1819 #1895 #1889 #1891 #1893 #1895 #6253 #12814 #12929 W6W H21W 2-B miniature bayonet #9428049 GM #25450 GE #9428049 GM #9417863 GM #9416927 GM #127934 GM #274020 GM #274004 GM #157135 GM Beetle 1950-1979 Beetle Cabrio 1950-1979 Caddy 1983-1992 Corrado 1989-1995 Golf Cabrio 1979-1992 Golf Mk1 1974-1983 Golf Mk2 1984-1991 Karmann Ghia 1960-1974 Scirocco 1974-1989 T2 Bay 1968-1979 T2 Split 1950-1967 T4 1991-2003 Type 3 1962-1973

363 LED Bulb 25 3528 available in White 6000K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). 25 3528 SMD chips. About 80 Lumen side fire and 20 Lumen forward fire. Uses about 1.5 Watt. Comparable to a 10 Watt to 15 Watt incandescent light bulb. BA9S base great for dashboard and turn signals, instrument panels. CE and Rohs. Long life up to 30,000 hours. 360 Viewing degree. Dim-able with a dashboard dimmer. LED bulb has built in ballast to operate from 8V to 15V. The ballast is a resistor. Compatible with 1953 Cessna 170 ba9s light bulbs.

LED Bulb Flat top. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic pure color, low heat generation, virtually unbreakable. Available in super white 6000K, Red 625nm, Green 526nm, Blue 464nm, Amber Yellow 594nm, RGB "cycles Red, Green, Blue", Ultra violet. Up to 25mA@13.8VDC. Operates from 6 to 12 Volts DC. Up to 345mW. Viewing angle approximate 120 degrees. Up to 7 Lumen output White 6000K. Operates in negative ground vehicle or motorcycles. Dimmable with a dashboard dimmer switch. Works in negative ground vehicles and motorcycles, scooters. Comparable to a 4 Watt to 9 Watt incandescent light bulb. CE and Rohs listed. Up to 30,000 hours. Compatible with 1953 Cessna 170 ba9s light bulbs. Dimmable with a variable voltage supply such as a dashboard dimmer switch. 9mm diameter base. Single contact with even bayonets. 0.96" tall M.O.L. "maximum overall length".

615 Led Bulb Super Flux. 4 side firing super flux LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow and blue. Uses about 114 mA @ 13.8V DC 1.573 Watt. This led bulb is very bright since the led uses super flux leds. This LED measures approximately 1.30 inches by 0.64 inches. Comparable to a 10 to 15 Watt incandescent light bulb. Up to 30 Lumen output. Dim-able using a dashboard dimmer. CE and Rohs listed. Compatible with 1953 Cessna 170 ba9s light bulbs.

1445 Led Bulb super flux. 1 LED. Durable, shock and vibration proof, instant On/Off. Works from 6 to 12 Volts DC negative ground. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 120 degree viewing angle. Uses up to 25mA@13.8VDC, 345mW. Compatible with 1953 Cessna 170 ba9s miniature bayonet light bulbs. BA9S #44 #53 #57 #182 #257 #363 #430 #615 #756 #1445 #1155 #1815 #1819 #1895 #1889 #1891 #1893 #1895 #6253 #12814 #12929 W6W H21W 2-B miniature bayonet #9428049 GM #25450 GE #9428049 GM #9417863 GM #9416927 GM #127934 GM #274020 GM #274004 GM #157135 GM Beetle 1950-1979 Beetle Cabrio 1950-1979 Caddy 1983-1992 Corrado 1989-1995 Golf Cabrio 1979-1992 Golf Mk1 1974-1983 Golf Mk2 1984-1991 Karmann Ghia 1960-1974 Scirocco 1974-1989 T2 Bay 1968-1979 T2 Split 1950-1967 T4 1991-2003 Type 3 1962-1973

BAY9S base led light bulb. This base bayonets are positioned 120 degrees apart. This bulb is also Canbus compatible. This is not a standard BA9S where the bayonets are positioned 180 degrees apart. There are five 5050 leds up to 150 Lumen output. Uses only 1.5 Watts at 12 volts dc. Each LED has 3 LED chips. Durable, shock and vibration proof, instant On/Off. Comparable to a 12-15 watt incandescent bulb. Measures .45in wide and 1.17in from top to bottom. Available in super white 6000K. Uses about .110 A @ 13.8V DC. Please note this product is polarity sensitive operates on negative ground chassis. Dim-able. Self ballast rated voltage from 8V to 15V. 360 degree viewing angle. Dim-able using a variable voltage supply such as a dashboard dimmer switch. Since this bulb is CanBus compatible this will eliminate error codes by using a non CanBus bulb. Approximate length from top to bottom is 1.155".

1155 LED BA9S Bulb has 4 SMD 3528 1 Chip LED. 12V DC. Uses about .56 Watts @ 12V. Up to 40 Lumen output. Low profile, low heat, long life up to 30,000 hours. Uses reliable LEDs for long life. Comparable to a 5 watt incandescent light bulb. Comparable to a 4 Watt to 9 Watta incandescent. Dim-able using a dashboard dimmer. 120 Degree viewing angle. CE and Rohs listed. Long life up to 30,000 hours. Compatible with 1953 Cessna 170 ba9s light bulbs. Compatible with the following BA9S #44 #53 #57 #182 #257 #363 #430 #615 #756 #1445 #1155 #1815 #1819 #1895 #1889 #1891 #1893 #1895 #6253 #12814 #12929 W6W H21W 2-B miniature bayonet #9428049 GM #25450 GE Beetle 1950-1979 Beetle Cabrio 1950-1979 Caddy 1983-1992 Corrado 1989-1995 Golf Cabrio 1979-1992 Golf Mk1 1974-1983 Golf Mk2 1984-1991 Karmann Ghia 1960-1974 Scirocco 1974-1989 T2 Bay 1968-1979 T2 Split 1950-1967 T4 1991-2003 Type 3 1962-1973

1895 LED Bulb has 24 Super Flux T10 Wedge BA9S 36 mm Festoon LED Light Bulb. This bulb uses 24 super flux LEDs. The color is white approximate 5500-6500 Kelvin. Low voltage 12 VDC. Has T10 Wedge, BA9S and 36 mm Festoon. Has 3m double sided tape so you can stick this led light almost anywhere. This led measures 2.30 inches by 0.96 inches. Dim-able with a dashboard dimmer switch. Comparable to a 10 to 15 Watt incandescent light bulb. Compatible with 1953 Cessna 170 ba9s light bulbs.

182 LED Miniature Bulb great for turn signals, dome light, side marker, dashboard as well as boat and RV usage. Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). Up to 150 Lumen output. 2.5 Watt @ 12v DC. Long life up to 30,000 hours. Comparable to a 20 watt incandescent bulb. Very bright! Dim-able using a dashboard dimmer switch. Compatible with 1953 Cessna 170 ba9s light bulbs. BA9S miniature bayonet #44 #53 #57 #182 #257 #363 #430 #615 #756 #1445 #1155 #1815 #1819 #1895 #1889 #1891 #1893 #1895 #6253 #12814 #12929 W6W H21W 2-B miniature bayonet #9428049 GM #25450 GE #9428049 GM #9417863 GM #9416927 GM #127934 GM #274020 GM #274004 GM #157135 GM Beetle 1950-1979 Beetle Cabrio 1950-1979 Caddy 1983-1992 Corrado 1989-1995 Golf Cabrio 1979-1992 Golf Mk1 1974-1983 Golf Mk2 1984-1991 Karmann Ghia 1960-1974 Scirocco 1974-1989 T2 Bay 1968-1979 T2 Split 1950-1967 T4 1991-2003 Type 3 1962-1973

815 7 LED Miniature Bulb 7 LED BA9S T3 1/4 light. 12 Volt DC. BA9S. Available in white only. Low power consumption. Durable, shock and vibration proof, instant On/Off. Monochromatic pure color, low heat generation, virtually unbreakable. Very bright. Uses T3 LEDs. This LED measures from top to bottom .92in and a diameter of .44in. Approximately 50 Lumen output. Approximate 35 degree viewing angle. Uses approximately 1/2 Watt, comparable to a 10 Watt incandescent bulb. Dim-able with a variable DC power supply. Please note this product is polarity sensitive. This bulb operates 12v DC can range from 10v to 15v. The bulb is self ballasted using a resistor. Compatible with 1953 Cessna 170 ba9s light bulbs.

1893 LED Miniature Bulb 1 Watt LED. 12 Volt DC. 80 Lumen output. Lifespan up to 30,000 hours. Available in limited quantities of Red(625nm) and Blue(464nm) only. Comparable to a 8-10 watt incandescent bulb. The white uses about 30mA @ 12.8V DC. CE and Rohs listed. Dim-able using a dashboard dimmer switch. 120 viewing degree. Compatible with 1953 Cessna 170 ba9s light bulbs. Compatible with the following BA9S #44 #53 #57 #182 #257 #363 #430 #615 #756 #1445 #1155 #1815 #1819 #1895 #1889 #1891 #1893 #1895 #6253 #12814 #12929 W6W H21W 2-B miniature bayonet #9428049 GM #25450 GE Beetle 1950-1979 Beetle Cabrio 1950-1979 Caddy 1983-1992 Corrado 1989-1995 Golf Cabrio 1979-1992 Golf Mk1 1974-1983 Golf Mk2 1984-1991 Karmann Ghia 1960-1974 Scirocco 1974-1989 T2 Bay 1968-1979 T2 Split 1950-1967 T4 1991-2003 Type 3 1962-1973

12814 Bulb 3 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 29mA@13.8 VDC 400mW. Up to 20 Lumen output. Dim-able using a dashboard dimmer. Comparable to a 4W to 9W incandescent light bulb. 60 Degree viewing angle. Ballasted using a resistor rated voltage 8V to 15V. Compatible with 1953 Cessna 170 ba9s light bulbs. Compatible with the following BA9S #44 #53 #57 #182 #257 #363 #430 #615 #756 #1445 #1155 #1815 #1819 #1895 #1889 #1891 #1893 #1895 #6253 #12929 W6W H21W 2-B miniature bayonet #9428049 GM #25450 GE Beetle 1950-1979 Beetle Cabrio 1950-1979 Caddy 1983-1992 Corrado 1989-1995 Golf Cabrio 1979-1992 Golf Mk1 1974-1983 Golf Mk2 1984-1991 Karmann Ghia 1960-1974 Scirocco 1974-1989 T2 Bay 1968-1979 T2 Split 1950-1967 T4 1991-2003 Type 3 1962-1973

1889 Miniature LED Bulb 4 LED's. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 48mA@13.8VDC 650mW. Comparable to a 4W to 9W incandescent light bulb. Dim-able using a dashboard dimmer switch. 60 degree viewing angle. Compatible with 1953 Cessna 170 ba9s light bulbs. Compatible with the following BA9S #44 #53 #57 #182 #257 #363 #430 #615 #756 #1445 #1155 #1815 #1819 #1895 #1889 #1891 #1893 #1895 #6253 #12814 #12929 W6W H21W 2-B miniature bayonet #9428049 GM #25450 GE Beetle 1950-1979 Beetle Cabrio 1950-1979 Caddy 1983-1992 Corrado 1989-1995 Golf Cabrio 1979-1992 Golf Mk1 1974-1983 Golf Mk2 1984-1991 Karmann Ghia 1960-1974 Scirocco 1974-1989 T2 Bay 1968-1979 T2 Split 1950-1967 T4 1991-2003 Type 3 1962-1973

6253 LED Bulb. Concave LED. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue, violet and color changing RGB . 25mA@13.8VDC 345mW. Up to 7 Lumen output. Viewing angle 90 degree. CE and Rohs listed. Comparable 4W to 9W incandescent. High performance long life up to 30,000 hours. Dim-able using a dashboard dimmer knob. Compatible with 1953 Cessna 170 ba9s light bulbs.

1891 Miniature LED Bulb. Has 5 LEDs. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green and blue. 12 VDC. Up to 12 Lumen output. Dim-able using a variable DC power supply such as a dashboard dimmer. This led light is self ballasted using a resistor. The lamp can operate from 8V to 15V. Comparable to a 10 to 15 Watt incandescent light bulb. Compatible with 1953 Cessna 170 ba9s light bulbs.

1895 LED Bulb 4 Ultra Bright 5050 SMD LED Light. 12V DC. Available in white only. Available in zero and 90 degree polarization. This LED bulb comes in 2 different offset designs: zero degree has 2 contacts placed on the sides of the base and the 90 degree has 2 contacts on the front and the back of the base. Please look at your fixture to see which the zero on ninety degree will work. Approximate size is 1.47" long, .47" wide and .14" thick. Dim-able with a dashboard dimmer switch. Up to 30 Lumen output. Viewing angle 120 degree. Comparable 4W to 9W incandescent bulb. Compatible with 1953 Cessna 170 ba9s light bulbs.

12814 LED Miniature Bulb. 1 Ultra Bright Side Firing. 1 Watt output. 12 VDC. Available in red, yellow, super white, green and blue. .46 diameter and 1.02 length. Replaces the following BA9S 53 57 182 257 363 430 615 756 1445 1155 1815 1819 1895 1889 1891 1893 1895 6253 12814 12929 W6W 2-B miniature bayonet. Dimmable with a variable voltage source such as your dashboard dimmer switch. Comparable to a 4 - 10 Watt incandescent bulb. 120 Degree viewing angle side firing. CE and Rohs.

The BA9S led bulb is designed to operate at 6 volt ac or dc for both positive ground and negative ground vehicles. Small outline to match the outline of a 51 bulb. .7 inches long by .46 inches wide at the plastic ring. The base is .39" wide. Up to 135 Lumen output. The led's are small 7020 smd so they are very low profile. The life is up to 30,000 hours. The bulb is comparable to a 4 to 10 watt halogen light bulb. The viewing angle of the 7020 LED's is 120 degrees. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow/Amber. CE and Rohs listed. These led's are 80% energy savings really helps the low power generator provide power. This led bulb is dim-able using a dimmer switch or variable voltage supply. These led light bulbs work great for instrument panels using the different colors. Since led's generate their own color no plastic colored caps or painted light bulbs needed.

For vehicles that are negative ground. Up to 40 lumen forward firing, and 40 lumen side firing, 6 volt DC, CE, Rohs listed, low power, long life. Uses about .110A at 6 volt DC. This bulb is dimmable with a variable power supply. Comparable to a 10-20 Watt incandescent bulb.

1847 LED Miniature Bulb works for both 6V positive ground chassis or 6V negative ground chassis. The led bulb is non-polarity 6 Volt BA9S. Sub miniature bayonet. Up to 80 Lumens, about 40 forward firing and 40 Lumens side firing. Up to 3 CP candle power forward firing and up to 3 CP candle power side firing. This bulb is dim-able using a variable power supply such as the dashboard dimmer knob. Rated life up to 30,000 hours. Uses .09 Amps @ 6 Volts. Up to 1 watt LED power comparable to a 10 Watt incandescent bulb. Made with six 5630 SMD led chips. Overall length 1.097" and .47" diameter. T3 1/4 Tubular package. Great for vintage, classic, cars, trucks, tractors, scooters or motorcycles. Excellent replacement for pinball, arcade and amusement rides.

12929 Miniature LED Bulb LED Panel 24 SMD 5050 T10 BA9S 36mm. Low Voltage 12 volt direct current. Has 24 super bright 5050 SMD LEDs. Has 3 adapters T10 wedge, BA9S and 36 mm festoon. This product has an adhesive back for easy mounting and installation. This product measures 2.58 inches by 1.74 inches. Available in White 6000K only. That is the correct dimensions, the video dimensions are stated incorrectly. Dim-able with a dashboard dimmer switch. Up to 300 Lumen output. 120 degree viewing angle. Comparable to 25 to 35 Watt incandescent light bulb. Compatible with 1953 Cessna 170 ba9s light bulbs. Uses up to 4 watts. Uses current up to 12 Volts@.40A.

BA9S 6 Volt DC Short round L.E.D. Light. Use this led bulb for lower voltage applications. CE and Rohs listed. Long life up to 30,000 hours. Approximate 7 Lumen output, 120 degree viewing angle. Uses approximately 25mA. @13.8VDC 345mW. Available in White 6000K, Red(625nm), Blue(464nm) & Yellow(594nm). The white color will start to illuminate around 2.6 volts DC and gradually get brighter up to 6 volts DC. This bulb is dim-able with a dashboard know or variable voltage supply. This bulb will work on 6 Volt negative ground vehicles. Comparable to a 4 to 9 Watt incandescent bulb. Compatible bulb: 51 55

BAX9S Can-Bus "Error Free" version, Type: BAX9S H6W LED type: 5 x 3-Chip 5050 SMD, Viewing angle: 360 degrees, 10.5 to 14.8 Volt DC. Overall height: about 42 mm. Long life, vibration and shock proof. Base diameter: about 9 mm white 6000 kelvin, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Uses approximately 2.5 watts @ 12 Volt D.C. Use this CAN Bus error free code so you can use L.E.D. versus and incandescent light bulb that will burn out and have to replace it again Long life up to 30,000 hours. Up to 180 lumen output. The 5050 SMD L.E.D. have 3 chips so it is very bright and long lasting.

CAN Bus "Error Free" version, Type: BAX9S H6W LED type: 5 x 3-Chip 5050 SMD, Viewing angle: 360 degrees, 10.5V - 14.8V Overall height: about 35mm. Long life, vibration and shock proof. Base diameter: about 9 mm white 6000 kelvin, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Uses approximately 1.3 watts @ 12 VDC.

BAX9S Short Round LED Light. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white 6000K, red, yellow, green and blue. Operates 6 to 12 VDC. Replaces H6W, 433. Simple to replace just remove your old incandescent bulb and replace with the new led light and save energy, gas, easier on electronics, wiring alternator. The BAX9S does not fit BA9S socket. 120 degree viewing angle. Comparable to a 4 to 9 Watt incandescent bulb. CE and Rohs.

Super bright 12 One Watt LED's 12 Volt DC. Works only negative ground vehicles. Can use BA9S or T10 Wedge or 36mm Festoon. Available in White 6000K. Up to 1200 Lumen output. 120 Degree viewing angle. Dimmable with a variable voltage supply. Has double sided sticky tape on the back side. CE and Rohs.

LED Bulb 12V no polarity BA9S base. Long life up to 30,000 hours. CE and Rohs listed. Up to 75 Lumen output. 360 degree viewing angle. Works either positive chassis or negative chassis cars, trucks and motorcycles. Comparable to a 4 to 9 Watt incandescent light bulb. The base is 10mm diameter with one contact on the bottom. Dim-able with a variable voltage source such as your dashboard dimmer switch. Available white 6000k, warm white 3000k, green, red, blue and yellow.

BA9S LED bulb for 12 Volt AC or DC. Works great for positive or negative ground. Up to 1.5 Watt. Up to 100 Lumen or 7.5 CP candle power output total. Dimmable with a variable voltage supply. The length of the bulb is 1.148". The diameter of the bulb is 0.458". Long life up to 30,000 hours. This bulb is dim-able with a variable voltage supply such as your dashboard dimmer. Up to 1.5 Watts. Up to 60 Lumen output or 4.5 CP candle power forward firing. Up to 40 Lumen or 3 CP candle power output side firing. Comparable to a 15 Watt incandescent bulb. Available in White 6000K, Warm White 3000K, Red, Green, Blue and Yellow. This lamp is not polarity sensitive so it can work either AC or DC. 360 Degree viewing angle. Made with 5050 SMD chip. Each SMD chip has 120 degree viewing angle. There is a built in ballast so this bulb can be operated at 12 Volts. CE and Rohs. Compatible with 1895 miniature base.

E10 Screw Bulb Led Short Round 6V to 12V DC. Virtually unbreakable, reliable performance. Available in super white, red, yellow, green, blue and rgb. 120 degree viewing angle. Uses only 20mA@13.8 Volts DC. Approximate size is .92in x .39in 10 mm(height x diameter). Fits T3 1/4, T3.25 size bulbs. E10 Miniature Screw Base. Short Round LED Light. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, . 6V to 12v DC. This LED lamp has built in ballast that allows the LED bulb to operate from 6V to 15V. Comparable to a 4 to 9 Watt incandescent led bulb. The bulbs works in negative ground or negative chassis cars, trucks, motorcycles, tractors and scooters. Up to 7 Lumen output. Long lasting life up to 30,000 hours. Mini indicator LED lamp. Dim-able using a dashboard dimmer knob.

Miniature Screw E10 Base One Watt High Power LED Light 6 to 12 Volts DC. Use this E10 Screw base for instrument panels, dash boards and other E10 Screw base applications that will save energy using LED Light technology. This high power 1 watt LED uses 2 LED chips so it is brighter. Up to 45 mA@13.8 volts. Up to 30,000 hours or longer LED Life. 120 degree viewing angle. Up to 70 Lumen output. Maximum voltage 16 volts. Dim-able by variable DC supply such as your dashboard dimmer switch. Comparable to 8 to 15 Watt incandescent bulb. This led lamp operating Temperature Range -30c to +75c. Max 150mA, 300mA pulsed 1/10th .1ms pulse width. One per package. Very bright LED, very nice. White 6000K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). When replacing the alternator indicator warning for Triumph Spitfire, please make sure to add a load equalizer.

52 Led Bulb Tall Round Miniature E10 Screw Base. 1 LED. Durable, shock and vibration proof, instant On/Off. Operates 6 to 12 Volts DC. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green, blue and rgb. Approximate light output is 20-30 Lumens. Uses .02 mA@13.8VDC. Approximate size is 1.10in x .39in 10mm (height x diameter). Dim-able with a variable DC power supply such as a dashboard dimmer. Operates from 6 volt to 12 volts. Can operate rated up to 15 to 17 Volts for a short period of time. Comparable to a 4 to 7 Watt incandescent bulb. This Lamp is G-3 1/2 Shape. Up to 7 Lumen output. Life up to 30,000 hours. CE and Rohs listed. Compatible replaces the following bulb numbers 1487 GE 27356 LM1012MS-B 52 258 428 1446 1449 1487

E10 Screw Base (T10) Hi Flux LED Light. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow, green, blue and rgb. Uses .02 mA@13.8VDC. Approximate size is .95in x .39in 10mm (height x diameter). Long life up to 30,000 hours. CE and Rohs certified. Dim-able with a variable dc power supply such as a dashboard dimmer. comparable 4 to 9 Watt incandescent. This led has up to 7 Lumen output. This bulb is solid state so you do not have to worry about broken filament or glass bulb. The led light is created by the material used to make the led bulb. Compatible with the following bulb numbers 52, 258, 428, 1446, 1449, 14876 1482, 1487.

1487 led bulb e10 Miniature Screw Base 5 5050 SMD. 5 5050 3 chip LEDs. Up to 40 Lumen side firing and 50 Lumen forward firing. Very nice product for E10 screw base applications. 12 Volt direct current. Up to a 15 watt incandescent comparison. Approximate size is 1.15in x .39in. 10mm dia. White 6000K, Daylight White 4400K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). This product is dim-able using a variable DC power supply. The bulb will start lighting at 7.5 Volts DC@.0002 Amp and at 12.8 volts DC the current is 70 mA. The bulbs rated voltage is 12 volts but can operate up to 15 to 17 volts DC. The led lamp is dim-able using a variable voltage supply such as a dash board dimmer knob. Great for dashboards, glove boxes, door panels, instrument panels, dome. The led bulbs color is pure colors created by the material the led chip is made from.

258 Led Bulb Flat E10 Screw Base. 1 LED. Durable, shock and vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable. Available in super white, red, yellow amber, green, blue, ultra violet and color changing rgb. Uses .02 mA@13.8 VDC. Approximate size is .89in x .34in (height x diameter). Up to 7 Lumen output. Long life up to 30,000 hours. CE and Rohs listed. Dim-able with a variable DC power supply such as a dashboard dimmer switch. Great for dashboard indicators, glove box, dome light, instrument panels. Compatible replacement 1487 52 258 428 1446 1449 1487

1449 LED Bulb E10 Screw 9 5050 (3 chip) 12 V DC. Each 5050 puts out 20 Lumens for a total 180 lumens. Low voltage 12 v d.c. Miniature E10 led lamp screw base for automotive and other low voltage uses, Uses 2 watts. 1.24 inches long and .40 inches wide. Long life up to 30,000 hours, CE and Rohs listed. Dim-able with a dashboard dimmer switch. The led bulb is self ballasted and can operate up to 17 Volts DC for a short period of time. Compatible bulb numbers such as 52, 258, 428, 1446, 1449, 14876 1482, 1487

E10 Screw 13 5050 3 Chip 12 V DC. This miniature E10 screw base uses 13 5050 smd led's. each smd led outputs 20 Lumen, so a total of 260 Lumen output possible. Low voltage 12 V d.c. operation. 1.74 inches long and .40 inches wide. Long life up to 30,000 hours. 360 illumination. Up to 210 Lumen output. Maximum voltage 16 volts.Comparable to a 15 to 20 Watt incandescent bulb. CE and Rohs listed. Very bright LED lamp. Dim-able with a dashboard dimmer knob. Uses about 3 Watts. Self ballast by resistor rated up to 15V. Compatible with bulb numbers such as 52, 258, 428, 1446, 1449, 14876 1482, 1487

1482 LED Bulb E10 miniature screw base 6 Volt positive chassis or negative chassis. Since the E10 is no polarity or non polarity. The bulb low profile, long life up to 30,000 hours, low voltage. The bulb uses approximately 1 Watt at 6 Volts. Approximately 70 Lumen output. Single filament design. Long life. Low voltage for 6 volt only positive ground or negative ground applications. See product detail for warranty period. Available in white 6000k, warm white 3000k, red, green, blue and yellow. This led bulb is dim-able using a variable AC power such as the dimmer knob on the dashboard. Since this bulb is non polarity works great for pre world war II vehicles and motorcycles. Upgrade to this bulb for license, running, turn signal, interior for long life and low power. Since this bulb is non polarity you do not have to worry how the existing socket is wired since this bulb is non polarity.

E10 LED Miniature Screw 12 To 16 Volt AC. Operates 12 to 16 Volts AC or DC non polarity. Works either negative ground or positive ground. Up to 50 Lumen forward firing and 40 Lumen side firing output. Long life up to 30,000 hours. Made with 5 5050 led's. Available in white 6000k, warm white 3000K and red, green, blue and yellow. Great for older cars that have 12 volt positive or negative ground. Uses about 1.5 Watts @ 13.8 V. Great to replace your old incandescent bulb with a long life led bulb so you do not have to replace the the whole door bell fixture. Extended warranty please see product page for more details. This led bulb has no polarity for AC or DC applications. This led lamp is ac compatible 12v led lights with e 10 screw base. Since it is ac or dc you can use sockets wired with the ground as the tip or contact and the base as plus +. This way you do not have to rewire the sockets.

Small E5 Midget 1 L.E.D., Available in 6VDC, 12VDC and 24VDC options. Up to 7 Lumen output, long life up to 50,000 hours. Available in Warm White 3000K and White 6000K. Uses very low .1 W power, uses 20ma@6V, 13ma@12v. The viewing angle is 90 degrees. MINIATURE T1 3/4 MIDGET SCREW (E5) BASE BULB. Comparable to a 4 Watt incandescent bulb. CRI>75. The miniature led lamp is called E5 since the base is 5 mm in diameter. This bulb is real small for E5 female screw base socket or lamp holder. The bulb operates at 6 Volt, 12 Volt and 24 Volts. This led bulb works great for back lighting for the ignition switch and various other areas of the dashboard compatible with Rolls Royce cars. This bulb is compatible with #272-1143, 272-1143, #8362, #335, #373, #342, #399, #1768, #1775, 176769L, #7326, #1769 These are tiny led light bulbs. The lamp will turn on around 2.5 Volts and gets brighter up to 6 Volts.

Very small midget screw male base is used for instrument, panel and automotive lighting. Operates at 6 to 12 Volts DC. Can be dimmed with a variable DC power. This LED measures approximately 0.57 inches by 0.21 inches. MINIATURE T1 3/4 MIDGET SCREW (E5) BASE BULB. Replaces #8362, #335, #373, #342, #399, #1768, #1775, 176769L, #7326, #1769 Uses .023@12 volt dc Comparable to a 4 Watt incandescent bulb. Rated up to 50,000 hours. CE and Rohs listed. Viewing angle 90 degrees. CRI>75. Up to 3 Lumen output.

E5 Midget Concave L.E.D. bulb. The top is concave, operates 12 VDC, long life up to 50,000 hours, low power consumption, great for instrument panels, dashboards and other light indicators. Uses only 240mW. CE Rohsed. Available in white 6000K, warm white 3000K. The bulb is dim-able using a variable DC power supply such as the dashboard dimming knob. CRI>75. Uses about 10 mA at rated voltage. Up to 3 Lumen output. The viewing angle is 90 degrees. This led bulb is comparable to a 4 Watt incandescent light bulb.

E5 midget screw socket with solderable tabs T1 3/4. Use for small miniature projects such as instrument, model rail road, model rc cars, planes. E5 is very small and easy to install in these miniature projects. CE and Rohs.

Festoon Super Flux 4 LED Light. 12 Volt's DC. 4 forward firing super flux LED chips. Each super flux LED has 3 LED chips, makes total of 12 LEDs. The approximate size is 10mm height. Available in super white, red, yellow and blue. 4 Super Flux LEDs consumes .080 Amps of current 80mA@13.8VDC 1.14 Watts. Comparable to a 8 to 15 Watt incandescent. Long life up to 30,000 hours. Up to 100 Lumen output. CE and Rohs. Dimmable with a variable voltage supply. Replacement bulb number 3423 3425 6411 46413 6418 6423 6451 6461 6475 6476 6418 6461.

Festoon Super Bright LED Light. Available in red, green, blue, yellow, super white. Plastic lens. 12 V DC. Please select 1 1/2 Inches for the replacement bulb number 3423 3425 6411 46413 6418 6423 6451 6461 6475 6476 6418 6461. Long life up to 30,000 hours. CE and Rohs listed.

Festoon SMT Super Flux 2 LED Light. Available in red, green, blue, yellow, super white. Plastic lens. 12 VDC. Please select 1 1/2 Inches for the replacement bulb number 3423 3425 6411 46413 6418 6423 6451 6461 6475 6476 6418 6461.

Approximate power usage is 120 mA. With an equivalency of 110 lumens. Made out of aluminum this festoon is very durable. 12 VDC. 2 1/2 watts power consumption . Shock and Vibration proof. Instant on/off. monochromatic (pure) color. low heat. virtually unbreakable. 12 VDC. Available in Super White. Aluminum also provides excellent heat sinking. Approximate size is 10mm in width and 1 3/4 Inches long 42 millimeters. Please select 1 3/4 Inches for replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844.

Festoon SMT Super Flux 1 LED Light. forward firing super flux LED. Available 33 mm or 1 1/4 Inches. The approximate size is 31 mm 1 1/2 Inches by 10 mm and 10 mm height 3/8 Inch. Available in super white, red, yellow and blue. Uses .120 Amps @ 12 Volts DC. .07 Watts. Please select 1 1/4 Inches for replacement bulb number 3021 3022 3175 6428 6430 30922 DE3425. Comparable to a 4 to 9 Watt incandescent bulb. Long life up to 30,000 hours. CE and Rohs listed.

Festoon Super Flux 4 LED Light. 4 forward firing super flux LED chips. 12 Volt DC. The approximate size is 10mm height. Available in super white, red, yellow and blue. 4 Super Flux LEDs consumes .080 Amps of current 80mA@13.8VDC 1.14 Watts. Comparable to a 10-Watt incandescent bulb. Viewing angle 120 degrees. Long life up to 30,000 hours. Dimmable with a variable voltage supply such as your dashboard dimmer switch. CE and Rohs. Up to 80 Lumen output. 1 3/4 Inches for the replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844.

Festoon 39mm, 12V AC/DC, heat sink, 12 SMD 2835 LED's, these L.E.D.s are very bright, CE and Rohs listed, long life greater than 30,000 hours. small outline with bright output. The heat sink helps the led's long life, available white 6000k Up to 350 Lumens.

Festoon Plastic LED Light. Available 10x43mm (9 LEDs). Available in red, green, blue, yellow, super white. Plastic lens. 12 VDC. Up to 150 Lumen output. Replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844. Rohs listed. CE listed. Long life up to 30,000 hours. 120 degree viewing angle. Comparable 9 to 15 watt incandescent light bulb. Dimmable with a variable voltage supply.

Festoon Super Flux 6 LED Light 12 Volts. 18 forward firing super flux LED chips. Each super flux LED has 3 LED chips. 42mm or 1 3/4 Inches. This festoon measures approximately 1 ¾ inches by 0.33 inches. Available in super white, red, yellow and blue. 6 Super flux LEDs. Up to 170 Lumen output. Uses .120 Amps @ 12 Volts DC. 1.7 Watts. Dimmable with a variable voltage supply such as a dashboard dimmer switch. Comparable to a 15 to 20 Watt incandescent bulb. 120 degree viewing angle. Long life up to 30,000 hours. CE and Rohs. Compatible numbers 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844

Made out of aluminum this festoon is very durable. 12 VDC. Approximately 31mm in length(from tip to tip) and 10mm in width. Shock and Vibration proof. Instant on/off. monochromatic (pure) color. low heat. virtually unbreakable. 12 VDC. Available in Super White. Aluminum also provides excellent heat sink. 100mA. Light output is 130 lumens. Please select 1 1/4 Inches for replacement bulb number 3021 3022 3175 6428 6430 30922 DE3425.

Approximate power usage is 120 mA. With an equivalency of 140 lumens. Made out of aluminum this festoon is very durable. 12 VDC. Shock and Vibration proof. Instant on/off. monochromatic (pure) color. low heat. virtually unbreakable. 12 VDC. Available in Super White. Aluminum also provides excellent heat sinking. Approximate size is 10mm in width. Please select 1 1/4 Inches for replacement bulb number 3021 3022 3175 6428 6430 30922 DE3425.

20 Lumen output. Festoon LED Light. Available 10x31mm (6 LEDs) Available in red, green, blue, yellow amber, white and ultra violet. Estimated usage is 30mA or 0.4 Watts. 12 VDC. This festoon measures 0.41 inches by 1.23 inches. Please select 1 1/4 Inches for replacement bulb number 3021 3022 3175 6428 6430 30922 DE3425. Dim-able with a variable voltage supply. 120 degree viewing angle. Comparable to a 5 to 10 Watt incandescent bulb. CE and Rohs.

3021 LED festoon bulb. The led light uses 1.5 Watt@ 13.8 Volts. The lap has a Ultra High Power Festoon 1 1/4 Inches/31mm. Very high power 1 1/2 watts of led light. 12 Volt operation. Available in white only.

Festoon Ultra Bright 20 SMT 1201 LED Light. 20 forward firing super flux LED chips. Available size is 42mm or 1 3/4 Inches. Available colors are white, red, green, blue and yellow amber. Please select 1 3/4 Inches for the replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844. Up to 175 lumens. Operates at 12 volts DC. 120 degree viewing angle. CE and Rohs listed.

Festoon 4 5050 SMT Ultra Bright 12 Volt DC. 1 and 1/4 Inches or 31mm LED Light. Very nice 31mm festoon with 4 SMD 5050 LEDs. Available in white only. Approximate size is 1.3in (height) x .43in (width). Works either 12 Volt AC or 12 Volt DC. Up to 75 Lumens. Dim-able with a variable voltage supply. CE and Rohs.

Festoon Plastic LED Light. Available 10x31mm (4 LEDs). Available in red, green, blue, yellow, super white. Plastic lens. 12 VDC. For replacement bulb number 3021 3022 3175 6428 6430 30922 DE3425. Up to 30 Lumen output. Dimmable with a variable voltage supply. 45 degree viewing angle. Comparable to a 4 to 9 Watt incandescent bulb.

Festoon LED Light. Available 10x39mm 9 LEDs Available in red, green, blue, yellow amber, super white and ultra violet. Glass lens. Estimated usage is .9mA or 1.2 Watts. Up to 70 Lumens. Comparable to a 5 to a 15 Watt incandescent bulb. 60 degree viewing angle. 12 VDC. Dim-able with a 12 Volt variable voltage supply such as the dashboard dimmer. Please select 1 1/2 Inches for replacement bulb number 3423 3425 6411 46413 6418 6423 6451 6461 6475 6476 6418 6461. The red and green leds are for a boat navigation light.

Festoon LED Light. Available 10x41mm (9 LEDs Available in red, green, blue, yellow amber, super white and ultra violet. Glass lens. Estimated usage is .9mA or 1.2 Watts. 12 VDC. Please select 1 3/4 Inches for replacement bulb number Dimmable using a variable voltage such as your dashboard dimmer switch. Up to 100 Lumen output. Long life p to 30,000 hours. Comparable to a 4 to 9 Watt incandescent bulb. CE and Rohs. 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844

40 Lumen output. Festoon LED Light. Available 10x36mm (6 LEDs), Available in red, green, blue, yellow amber, super white and ultra violet. Glass lens. Estimated usage is .9mA or 1.2 Watts. 12 VDC. Please select 1 1/4 Inches for replacement bulb number 3021 3022 3175 6428 6430 30922 DE3425.

Festoon LED Light. Available (9 LEDs) 1 3/4 Inches or 10x41mm. Available in red, green, blue, yellow, super white. Plastic lens. 12 VDC. Please select 1 3/4 Inches for the replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844

Festoon, 31mm, 2 Watt, 12 V AC/DC, Up to 30,000 hours, 160 Lumen output, 120 degree viewing angle. Very heavy duty heat sink. Available in White 6000K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow (594nm). Works great for replacement in vanity mirror. Comparable to a 15 to 20 Watt incandescent bulb. Long life up to 30,000 hours. CE and Rohs listed. Compatible with c5w, c10w.

Rigid loop LED festoon. 12 Volt A.C./D.C. 6 watts, up to 450 lumen output, comparable to a 30 to 50 watt incandescent bulb. Great for classic cars such as 1971-73 ford mustang mach 1. Uses 2 CREE X2 3 watt led's. Once installed this light does very well to light up the dome light, interior, dashboard and door lights that use the rigid loop festoon. CRI>80, long life up to 30,000 hours. The color is 6000 Kelvin.

1895 LED Bulb has 24 Super Flux T10 Wedge BA9S 36 mm Festoon LED Light Bulb. This bulb uses 24 super flux LEDs. The color is white approximate 5500-6500 Kelvin. Low voltage 12 VDC. Has T10 Wedge, BA9S and 36 mm Festoon. Has 3m double sided tape so you can stick this led light almost anywhere. This led measures 2.30 inches by 0.96 inches. Dim-able with a dashboard dimmer switch. Comparable to a 10 to 15 Watt incandescent light bulb. Compatible with 1953 Cessna 170 ba9s light bulbs.

Festoon 2 LED Super Bright LED Light 1 1/4 Inches / 31 mm. 12 Volt DC, available in super white only. This product measures approximately 1.23 inches by 0.43 inches. Up to 20 Lumen output. Dimmable with a variable voltage supply such as your dashboard dimmer switch. Long life up to 30,000 hours. 120 degree viewing angle.

Festoon SMD Super Flux 3 LED Light. Available in red, green, blue, yellow, super white. Plastic lens. 12 VDC. Please select 1 3/4 Inches for the replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844. 41mm or 1 5/8 Inches replaces bulb number 212 211 212-2 214-2 6413 6429.

This Festoon uses one 1.5 Watt LED. Uses 1.5 Watt @ 12 Volt D.C. Comparable to a 15 watt incandescent bulb. 1 and 1/2 Inches or 39 mm. Available in white only. Long life up to 30,000 hours. Very bright up to 180 lumen output. Uses low power 12 Volt DC. The thickness of the base is 10mmx10mm. Dimmable with a variable voltage supply. The viewing angle is 120 degrees. Comparable to a 10 to 15 Watt incandescent. Long life up to 30,000 hours. CE and Rohs.

Festoon LED 360 Degree 39 mm or 1 1/2 inches. Uses only 0.78 watts @ 12VDC. Available in white 6000-6500 kelvin, Warm White 3000K, Red, Green, Blue and Yellow/Amber. Output up to 150 lumens. Very nice, with 360 degree viewing angle. 8 5050 SMD LEDs each use only 0.2 watts. For 12 Volt DC systems. Long life up to 30,000 hours. Perfect for interior dome lights and license plate lights. Great for boat cabin lighting. 1 per package. Dimmable with a variable voltage source as your dashboard dimmer switch. Comparable to a 4 to 9 Watt incandescent festoon. CE Rohs

8 5050 SMT Full 360 Degree LED Light bulb 6mm. Very nice shoots light in 360 degrees. 12 Volt DC. Available in white only. Each 5050 LED has 3 chips. Approximate size is 1.50in x .40in. Available white 6000k, warm white 3000k, red, green, blue and yellow. Up to 150 lumen's. Long life up to 30,000 hours. Comparable 9 to 16 Watt incandescent. Uses 80% less energy that a incandescent bulb. Dim-able with variable voltage supply. CE and Rohs. Solid state so no more broken filaments.

Festoon 6 SMD Ultra Bright. Has 6 5050 LEDs. Very Bright 31 mm package. 12 VDC. Available in white only. 120 degree viewing angle. Each 5050 SMD has 3 chips. Up to 30,000 hours. Output up to 120 Lumens. Uses very low power and is solid state for long life. The LED's are cool to the touch, which means they last longer than a hot filament incandescence bulb. Dimmable with a variable voltage supply. Comparable to a 8 to 15 Watt incandescent bulb. CE and Rohs.

Festoon, 42mm, Up to 3 Watt, 12 VDC/AC, 120 Viewing, UP to 225 lumens, Up to 30,000 hours. White 6000K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). Has nice metal heat sink. Dim-able with a variable power supply such as your dashboard dimmer switch. Comparable to a 24 to 27 Watt incandescent bulb. The dim-able voltage range is around 8.00 volts 0% light output to 13.8 volts 100% light output. Compatible with 211-2 GMC K1500 dome light 273. Compatible with 1980 MGB.

3 Watt, up to 240 lumen, up to 25,000 hour lifespan, 120 degree viewing, 12 Volt AC or DC. Made with metal heat sink to reduce the temperature of the leds, for longer life. White 6000K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). CE & Rohs. Compatible with c5w and c10w.

Festoon Canbus error free. Uses high power 7060 L.E.D. Long life up to 30,000 hours, 12 Volt AC or DC. CE and Rohs listed. Available in white 6000K. Up to 300 Lumen output. Uses about 2.5 Watts @ 13.8 Volts. 180mA@13.8 Volts. 120 degree viewing angle. Operates from 6 volts to 13.8 Volts. Works in both positive ground and negative ground. Dimmable with variable voltage. Comparable to a 9 to 21 Watt incandescent.

T6 Festoon 3 SMD LED light. This L.E.D. is used for vanity lights, the T6 is smaller diameter than a normal festoon. 12 Volt. Available in white 6000K. CE and Rohs listed. Comparable to a 4 to 9 watt incandescent light bulb. 120 degree viewing.

Festoon 360 Degree 4 SMD 5050 (3 chip). 1 and 1/4 Inches or 31mm (height) x .43in (diameter). This is the first SMD 360 LED Festoon that emit light in all directions. 12 VDC. Available in white 6000k, warm white 3000K, red, green, blue and yellow/amber. 50mA @ 12.8V. Up to 60 lumen output. Long life up to 30,000 hours. CE and Rohs. Comparable to a 10 to 15 Watt incandescent bulb. Dimmable with a variable voltage supply such as your dashboard dimmer switch. 360 degree viewing angle.

Festoon Super Flux 9 LED Light. 9 forward firing SMD LED chips. Available size is 41 mm or 1 3/4 Inches. Available in super white, red, yellow and blue. Please select 1 3/4 Inches for the replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844.

42mm 8 1210 SMD LED Lighting with Hook. 42mm in length. Has hooks on each end. has 8 1210 SMT LEDs. 12 Volt DC. Available in white only. #561 replacement. Very bright, very nice replacement. Up to 140 Lumen output. 120 degree viewing angle. Dimmable with a variable voltage supply such as your dashboard dimmer switch. Uses .1 amp @ 13.8 Volts DC. Uses up to 1.40 Watts. Long life up to 30,000 hours. Comparable to a 10 to 15 Watt incandescent. Compatible with: 1971-1973 Ford Mustang Mach 1

Festoon Super Flux 4 LED Light. 4 forward firing super flux LED chips. Each super flux LED has 3 LED chips, makes total of 12 LEDs. The approximate size is 10mm height. Available in super white, red, yellow and blue. 4 Super Flux LEDs consumes .080 Amps of current 80mA@13.8VDC 1.14 Watts. Please select 1 1/4 Inches for replacement bulb number 3021 3022 3175 6428 6430 30922 DE3425. Please select 1 1/2 Inches for the replacement bulb number 3423 3425 6411 46413 6418 6423 6451 6461 6475 6476 6418 6461. Please select 1 3/4 Inches for the replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844

1.5 Watt Ultra High Power Festoon 1 1/2 Inches/36mm. Very high power 1 1/2 watts of led light. 12 Volt operation. Available in white only.

Up to 75 Lumen output. Festoon LED Light. Available 10x43 mm (10 LEDs Available in red, green, blue, yellow amber, super white and ultra violet. Glass lens. Estimated usage is .9mA or 1.2 Watts. 12 VDC. This bulb is dim-able with a variable voltage supply such as a dashboard dimmer switch. Very nice 10 bright LEDs really make this product light up the area. Please select 1 3/4 Inches for replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844. Comparable to a 10 to 20 Watt incandescent festoon. Long life up to 30,000 hours. CE and Rohs. 120 degree viewing angle.

LED Festoon, 36mm, 3 Watt, 12 Volt AC/DC non polarity works both positive ground or negative ground. 120 Degree Viewing. Made with 5730 SMD chips, each chip is up to .5 watt. Up to 300 lumens. Life spans up to 30,000 hours. White 6000K, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm) & Yellow(594nm). Dimmable with a dashboard dimmer switch. Comparable 27-Watt incandescent bulb. CE and Rohs.

Festoon 1210 SMT. 12 VDC. 6 1210 SMT LEDs. Available in white. 1 and 3/4 Inches or 41 MM

Festoon Super Flux 2 LED Light 12 Volt DC. 2 forward firing super flux LED chips. Each super flux LED has 3 LED chips, makes total of 6 LEDs. Available 36mm or 1 1/2 Inches. Available in super white, red, yellow and blue. 2 Super Flux LEDs consume .040 Amps of current 40mA@12 VDC .552 Watt consumption. Please select 1 1/4 Inches for replacement bulb number 3021 3022 3175 6428 6430 30922 DE3425. Please select 1 1/2 Inches for the replacement bulb number 3423 3425 6411 46413 6418 6423 6451 6461 6475 6476 6418 6461. Please select 1 3/4 Inches for the replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844. Variable dimming from 5 Volts to 13.8 Volts using your dashboard dimmer. Comparable to a 10 to 20 Watt incandescent bulb. Long life up to 30,000 hours.

44 mm led rigid loop festoon. 8pcs of 5050 leds. Low voltage 12V. Available in white 6000K. Great for 1971 through 1973 Mustangs, fastback and Mach 1 dome light. The 5050 smd has 3 leds for each 5050 chip, so a total for 24 led chips very bright. This LED bulb was used to replace a incandescent bulb and was brighter and looked better than the original through the dome light lens.

1.5 Watt Ultra High Power Festoon 1 1/2 Inches-39 mm. Very high power 1 1/2 watts of led light. 12 Volt DC operation. Available in white only. 120 degree viewing angle. Comparable to a 10 Watt festoon. Dim-able with a variable power supply. Up to 110 Lumen output. CE and Rohs. Long life up to 30,000 hours.

Festoon Super Flux 2 LED Light. 2 forward firing super flux LED chips. Each super flux LED has 3 LED chips, makes total of 6 LEDs. Available 31mm or 1 1/4 Inches. Available in super white, red, yellow and blue. 2 Super Flux LEDs consume .040 Amps of current 40mA@12 VDC .552 Watt consumption. Please select 1 1/4 Inches for replacement bulb number 3021 3022 3175 6428 6430 30922 DE3425.

Festoon Super Flux 2 LED Light. 2 forward firing super flux LED chips. 42mm or 1 5/8 Inches. Available in super white, red, yellow and blue. 2 Super Flux LEDs consume .040 Amps of current 40mA@12 VDC .552 Watt consumption. Comparable to a 4 to 9 Watt incandescent bulb. Dim-able with a variable voltage supply.Please select 1 3/4 Inches for the replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844. CE and Rohs.

35mm Festoon 4.5 watts. This festoon if 12V non polarity, works DC or AC with no flashing. Very bright 9 5730 LED's, each LED is 1/2 watt. Up to 550 lumen output, long life up to 30,000 hours, comes with heat sink so operates cooler for longer life. Comes in White 6000K and Warm White 3000K. 120 degree viewing angle.

Festoon LED Light. Available 10x43mm (9 LEDs Available in red, green, blue, yellow amber, super white and ultra violet. Glass lens. Estimated usage is .9mA or 1.2 Watts. 12 VDC. Please select 1 3/4 Inches for replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844. Dimmable with a variable voltage supply such as your dashboard dimmer knob. Comparable to a 4 to 12 Watt incandescnet bulb. Up to 80 Lumen output. Viewing angle 120 degrees. Long life up to 30,000 hours.

T6 LED Bulb, uses 2 5050 SMD tri chip leds. Small 28mm for visor and other applications. Long life up to 30,000 hours, up to 40 lumen output. 12 Volt DC applications, 80 degree viewing angle. Comparable to a 4 to 9 watt incandescent light bulb. CE and Rohs. Compatible with: 6612f

Festoon Two 1 Watt LED Light Bulb 1 and 3/4 Inches or 41 millimeter. Very bright uses 2 1 watt high power LEDs. 12 Volt DC. Available in white only 6000K. Up to 140 Lumen output. CE and Rohs listed. Extremely long life up to 30,000 hours. Comparable to a 20 to 29 Watt incandescent light bulb. 120 degree viewing angle. Has 2 forward firing leds.

12929 Miniature LED Bulb LED Panel 24 SMD 5050 T10 BA9S 36mm. Low Voltage 12 volt direct current. Has 24 super bright 5050 SMD LEDs. Has 3 adapters T10 wedge, BA9S and 36 mm festoon. This product has an adhesive back for easy mounting and installation. This product measures 2.58 inches by 1.74 inches. Available in White 6000K only. That is the correct dimensions, the video dimensions are stated incorrectly. Dim-able with a dashboard dimmer switch. Up to 300 Lumen output. 120 degree viewing angle. Comparable to 25 to 35 Watt incandescent light bulb. Compatible with 1953 Cessna 170 ba9s light bulbs. Uses up to 4 watts. Uses current up to 12 Volts@.40A.

LED Festoon, 31mm, 12 Volts AC with ceramic smooth cover lens and wavy ceramic heatsink on the back. Uses approximately 83mA @ 12 VAC. Made with 3 SANAN LED's for a reliable long life up to 30,000 hours. The viewing angle is 120 degrees. Up to 100 Lumen output. Comparable to a 9W to 15W incandescent bulb. Dimmable using a variable voltage supply such as your dashboard dimmer. Has a ceramic smooth lens and ceramic wavy back to keep out the environment so the festoon last longer and cooler. Available in White 6000K, Warm White 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Since the festoon is non polarity you can insert the bulb in either direction and still will work. Operates both 12 Volt positive ground and 12 Volt negative ground vehicles. The festoon length is 31mm or 1 1/4". CE and Rohs.

Festoon Super Flux 6 LED Light. 18 forward firing super flux LED chips. Each super flux LED has 3 LED chips. 36 mm or 1 1/2 Inches. The approximate size is 16mm by 24mm and 10mm height, or 5/8 (.625) Inch by 15/16 (.940) Inch and 3/8 (.375) Inch in height. Available in super white, red, yellow and blue. 6 Super flux LEDs. Uses .120 Amps @ 12 Volts DC. 1.7 Watts. Approximate light output up to 100 lumens. Please select 1 1/2 Inches for the replacement bulb number 3423 3425 6411 46413 6418 6423 6451 6461 6475 6476 6418 6461. Dimmable with a variable voltage supply such as your dashboard dimmer switch. Comparable a 10 to 15 Watt incandescent bulb. Long life up to 30,000 hours. 120 degree viewing angle. CE and Rohs.

High power festoon 31mm or 1 1/4 Inches. Outputs up to 3 watts of power at 12 Volts AC or DC. 120 viewing degree, up to 30,000 hours, Rohs and CE Listed. Up to 350 lumen output. Has heat sink to keep led's cooler for longer life. Dimmable with a variable voltage supply. Comparable to a 15 to 27 Watt incandescent bulb. Made with 5730 SMD's. Each 5730 can output up to 1/2 Watt of led power. Long life up to 30,000 hours. Available in White 6000K or Warm White 3000k. 120 degree viewing angle. Can be used 12 volt positive ground or negative ground. Compatible with: DE3157

Use this festoon for classic or antique automobiles or cycles that use 6 volt chassis. This led bulb works with negative chassis systems. The bulb uses about 3 watts at 6 volts. This bulb is dimmable with a variable power supply. The leds provide 360 degree illumination. The festoon is comparable to a 20 to 25 incandescent light bulb. This festoon works great for pinball machines that operate at 6.0 volts DC. Replaces Volkswagen Beetle light bulb: 43mm. Approximate size length 1.71" and the diameter is .45". N177231 N 17 723 1 4203 JAHN 1730

2.88 Watts @ 12 volts D.C. Up to 170 lumen, 1 3/4" 360 Degree Festoon with 12 5050 SMD 3 chip led's. 12 volts D.C. Great for license plate, dashboard and boat, airplane navigation. 42 mm. Very bright festoon that emits LED Light in 360 degree around the the festoon. Great for boats and other navigational systems that need bright lighting in al directions. DE3021 / DE3022 / DE3175 / 212 / 12844 / K25623. Available in White, Warm white, Red, Green, Blue and Yellow. This L.E.D. bulb has 360 degree illumination. Has the same shape as a incandescent festoon so it fits in most applications. Very bright and well made.

LED Festoon Super Flux 6 miniature bulb. 18 forward firing super flux super bright led chips. The festoon leds use about 1.7 Watts@13.8VDC. Each super flux LED has 3 LED chips. Six total super flux leds. Available in super white, red, yellow and blue. 6 Super flux LEDs. Uses .120 Amps @ 12 Volts DC. 1.7 Watts. Approximate light output 60 lumens. Comparable to a 11 to 19 Watt incandescent bulb. Long life up to 30,000 hours. This led festoon bulb has cool bright super flux leds. Dim able with a variable voltage source such as your dashboard dimmer. This led bulb works 12 volt negative ground vehicles. Available 33 mm or 1 1/4". Replacement bulb number 3021 3022 3175 6428 6430 30922 DE3425. Rohs and CE certified. Why is a led better than a comparable incandescent light bulb? The leds are solid stat. The leds do not have rugged parts the filament can break or the glass can break.

6 Volt no polarity festoon for older negative chassis automobiles or cycles. Zero to 6 Volts DC. Long life up to 30,000 hours. 360 degree illumination. Up to 70 lumen output. Great size outline to the same shape as a incandescence festoon. Comparable to a 10-20 watt incandescence festoon.

Festoon Ultra Bright 20 SMT LED Light. Available colors are super white, red, amber yellow, green and blue. This product measures approximately 1 ¼ inches by 0.90 inches. Operates on 12VDC only.

4 SMD Festoon, 3 chips per SMT LED. 80 mA. 40 mm. 9 mm diameter. Available in super white. Great for dome lighting in vehicles and interior lighting in boats and RVs. Replaces bulb numbers 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844. Up to 70 Lumen output. 120 degree viewing angle. Long life up 30,000 hours. Comparable to a 10 to 20 Watt incandescent festoon. Dimmable with a variable voltage supply such as the dashboard dimmer switch. CE and Rohs.

Approximate power usage is 120 mA. With an equivalency of 110 Lumens. Made out of aluminum this festoon is very durable. 12 Volts DC. Shock and Vibration proof. Instant on/off. monochromatic (pure) color. low heat. virtually unbreakable. Available in Super White. Aluminum also provides excellent heat sinking. Approximate size is 10mm in width and 1 1/2 Inches long 39 millimeters. Please select 1 1/2 Inches for replacement bulb number 3423 3425 6411 46413 6418 6423 6451 6461 6475 6476 6418 6461. 120 degree viewing angle. Compatible with MGB. Dim-able. Comparable to a 9-10 Watt incandescent bulb. CE and Rohs.

Festoon Plastic LED Light. 10x36mm (6 LEDs). Available in red, green, blue, yellow, super white. Plastic lens. 12 VDC. Please select 1 1/2 Inches for the replacement bulb number 3423 3425 6411 46413 6418 6423 6451 6461 6475 6476 6418 6461.

1.5 Watt Ultra High Power Festoon 1 3/4 Inches 41mm. Very high power 1 1/2 watts of led light. 12 Volt operation. Available in white only.

12 Super Flux LED's. Available in super white, yellow, red, blue, green. The approximate size is 1.2 inch by 1.7 inch. 140 mA @ 13.8 V DC. Very bright 440 lux @ 1 foot. Please select 1 3/4 Inches for the replacement bulb number 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 DE3022 DE3175 DE3425 DE4410 12844. Long life up to 30,000 hours. CE and Rohs certified. Up to 150 Lumen output. Viewing angle 120 degrees. Dimmable with variable voltage. Comparable to a 9 to 18 Watt incandescent festoon. Up to 2 Watt output, very bright.

6 Volt Festoon works with Positive Ground or Negative Ground. Up to 2 Watts of LED power. This festoon has 150 to 200 Lumen output. The led's are designed so that light lights in 180 degrees. This festoon is great for vintage, classic and antique cars, trucks and motorcycles. Vehicles made before World War II have a 6 volt positive chassis or 6 volt negative chassis. Since these LED's are AC non polarity they work great in these old vehicles. Long life up to 30,000 hours or longer. Available in White 6000K and Warm White 3000K. Comparable to a 15 to 20 Watt glass festoon incandescent light bulb. This festoon works great for pinball machines that are 6 volt AC systems. Certain amusement games and rides use 6 volt AC festoon so these are the perfect replacement. Long warranty please see warranty length on this detail page. The festoon viewing angle is around 240 degrees.

Festoon 6 volt for Positive Ground and Negative Ground vehicles. Up to 200 Lumen output. Long life up to 30,000 hours. Works non polarity AC or DC. Made with 6 5730 SMD high power leds. Available in White 6000 Kelvin and Warm White 3000 Kelvin. Vehicles and motorcycles made before World War II are positive chassis and this led bulb works perfectly. This led bulb is comparable to a 15 to 20 Watt incandescent glass festoon. The end caps are plated for rugged long life connection. Easy to install just remove the old festoon and insert the new led festoon plug & play. Since the new led festoon is non polarity you do not have to worry which way to install the bulb. Great replacement for 6 volt version of: 560 569 578 211 212 212-2 2122 214-2 2142 6413 6429 DE3021 ED3022 DE3175 DE3425 De44101284 6450 This is a perfect replacement for glove box and console lighting upgrades.

6 volt festoon positive chassis or negative chassis non polarity. Up to 200 Lumen output. 1 1/4 length. Uses only 2 Watts, comparable to a 15 to 20 Watt glass festoon incandescent bulb. Since it is non polarity just insert into the festoon socket. Long life up to 30, 000 hours. Available in White 6000K and Wam White 3000K. The festoon end caps are rugged for secure electrical connection. Since the bulb is LED you do not have to worry about the filament breaking or the glass breaking. Great for arcade games and pinball machines. Since the festoon illuminates 180 degrees works great to illuminate the 180 degree viewing angle. The Warm White is closes color to a incandescence light bulb. The festoon has 6 chip high power 5730 SMD LED's. The diameter is .41 inches. Replaces 6 volt version of 3021 3022 3175 6428 6430 30922 De3425 C5W. The light is very clean and vivid.

Festoon 39mm 3 Watt 6 x 5730 SMD 24V AC/DC 1 1/2 inch. Up to 240 Lumen output. Uses a metal heatsink to keep the leds cooler. Made with Samsung leds for long life. Uses 6 smd 5730 smd's. Available in White 6000K and Warm White 3000k. Long life up to 30,000 hours. About 1 1/2 inches long. CE and Rohs. Dim-able with a variable voltage supply. Compatible with: 5wxenon

LED Lighting 1 Pair 14 LED 12 VDC. Each driving light has 14 super bright LEDs. Grey finish, angled bracket. The red/grey wire in +12 VDC and the ground the grey wire. 12 Volt DC only. Uses 2 watts of power. The lights brackets have double sided sticky tape to mount the led lights to the car.

Extreme Bright LED Day Light Driving Lights. 11 extreme bright LEDs. Up to 2 Watt output comparable to a 20 watt light bulb. 12 VDC. Sold as a pair. Up to 140 Lumens. Chrome plated spray, looks very nice. Includes angled mounting brackets and wire. This product measures 4.38 inches by 1.18 inches with a thickness of 1.18 inches. Adhesive mount extends 0.80 inches and measures 2.72 inches by 1.06 inches.

Product Code: 45863 880 13 SMT LED Daylight Running Lamp. Great replacement saves batteries. 12 Volt automotive. Available in white only. Has 13 3 Chip 5050 SMT LED's. 1 forward firing and 12 side firing LEDs for a higher brightness intensity. Only use for your fog light. This product measures approximately 2.24in tall, the base is 1.02in long, and the light tower is .42in wide. Uses Approximately 3.12 watts, comparable up to a 25 watt incandescent bulb.

881 13 SMT 5050 (3 Chip) LED Daylight Lamp. Each 881 has 13 5050 LEDs. Each LED has 3 LED Chips that make the led light even brighter. 1 forward firing and 12 side firing LEDs for a higher brightness intensity. Uses 2.69Watts, comparable to a 20 watt incandescent. Only use for your fog light. Operates 12 Volts. Available in white only. Approximate size is 2.28in x .43in x 1in x 1.34in. Replaces the 886 and 896.

30 LED's Total 1 Pair LED Day Driving Lights with controller. 12 Volt DC. This LED comes equipped with a remote controller that allows flash or no flash of the led lights, lighter outlet plug, durable, plastic, clear lens, aluminum incasing, loose wires for easy installation, adjustable stand for mounting and a sticky adhesive on bottom of stand. Available in white only. This product approximately measures 3.08 inches by 3.08 inches with an approximate 0.98 inch thickness. The adhesive mount measures 1.58 inches by 1.20 inches. The controller measures 3.02 inches by 1.40 inches. The remote measures 2.60 inches by 1.06 inches with a 0.85 inches thickness. Chrome finish.

Low Profile LED Driving Light 1 Pair. 12 Volt DC only, Each LED Light has 15 LEDs. Ultra thin design has brackets for mounting at any angle. Also the driving lights can be used as a backup light. The product measures 3.09 inches by 3.09 inches with a 1 inch thickness. Has an adhesive mount which measures 1.58 inches by 1.20 inches. Approximately 225 lumens per L.E.D. Driving Light. Chrome finish.

H11 18 SMD 5050 Day Driving L.E.D. Light. 12 VDC. Available in white only. Fits H 11 Light bulb for driving/fog/daylights. Approximate size 2.12in x .60in x 1.54in x 1.23in. Uses only 3.5 Wattage 30 watt output equivalency.

LED Driving Lights 1 Pair Low Profile. The kit includes 2 driving lights and a wired remote controller. The remote can change the lights from always on to beat/flash mode. Each driving light has 12 LEDs. The cigarette lighter plug measures 3.02 inches by 1.30 inches with a thickness of 0.75 inches. The remote measures 1.06 inches by 2.58 inches with a thickness of 0.82 inches. The led face measures 4.21 inches by 1.75 inches with a thickness of about 1 inch. Lights are Water resistant. Controller must stay dry. Chrome finish.

Driving Light Low Profile 8 High power LEDs 10-15VDC. Very bright, fits in tight locations, looks great, 6000K white. 12VDC. Comes with mounting kit. Measures 6.09" long, .71" wide, and 1.52" deep.

L.E.D. Daytime Running Light using MCOB technology, IP65 rated. 15 watt output each, white 6000K, 120 degree viewing, CE and Rohs listed. Perfect for a quick Daytime Running light solution. Long life up to 30,000 hours, low profile 12 volt power lighting. Up to 105 Lumen output. Easy for DIY installation for daytime running lights.

This H11 H8 880 881 Male Adapter to #18 awg wires. high efficient, heavy duty and heat resistant. Nylon female plug can withstand up to 1200 Fahrenheit. H11/H8 or 880/890 lamp connector for 12V use only. Up to 55 watts power per harness. Harness is approximately 7.75 inches long. Made with #18 awg stranded wiring to handle the high powered driving lights. Great for fog, driving or headlights. Water proof PVC and nylon plastic adapter and 6.5 inches #18 awg wiring. H11 H8 880 881 male are interchangeable, they all fit the same light bar, or cube light, fog light, headlight. Two insulation displacement connectors are included to connect the wire to the existing automobile harness with minimal damage to the automobile harness. Approximately 7.75" in overall length, with the wires being 6.5". Overall width of connector end is approximately 1.07", with the plug being 0.66".

9003 18 5050 (3 Chip) LED Fog Light. Saves power and has a long life. 12 VDC. Has 3 forward firing and 15 side firing LEDs, and only uses .12 mA @ 13.8 VDC. Ony use for your fog light.Comparable to a 15 watt incandescent equivalent. Approximate size is 2.50in x .58in x 1.87in. This LED Light only has 1 brightness level. 6000K.

Circular small projecting LED Lights 1 Pair. The kit Angled bracket, double sided sticky tape, mounting screws and approximate 5 feet of wire to hook up to a switch. Each light has 6 LEDs. The led face measures 3 inches by 2 inches with a thickness of about 2.25 inch. Chrome finish. The LED color is white 6000K. Perfect for small, focused lighting needs such as indoor signs, accent lighting, etc.

9006 LED Fog Light 18 5050 SMD (3 Chip). 12 VDC. Available in white 6000K. Great for 9005 9006 Fog Light replacements. This LED measures from top to bottom 2.40in, a radius of .58in and the width of the base is 1.43in. 3 forward firing and 15 side firing. 1 per package. Up to 400 Lumen output. Comparable to a 35 to 45 watt incandescent. 360 degree illumination. Easy to install just remove old light bulb and insert new led bulb. CE and Rohs listed. Long life up to 30,000 hours. Compatible with: 9005 9006 HB3 HB4 H10 9040 9045

H3 12 5050 (3 Chip) LED Fog Light. Saves power and has a long life, cool look. 12 VDC. Has 12 5050 side firing LEDs, and only uses .09 mA @ 13.8 VDC. Ony use for your fog light. Comparable to a 10 watt incandescent equivalent. The maximum overall length is 1.875" that is from the top to bottom of the bulb. The width of the bulb not including round flange is .453". The round flange maximum diameter is .866". CE and Rohs.

H7 18 SMD 5050 (3 Chip) LED Fog Light . 12 VDC or 12 VAC. Up to 300 Lumens. Available in white 6000K. Long lasting L.E.D. technology eliminates changing the fog lamp. 3 forward firing and 15 side firing LEDs, and only uses .25 mA @ 13.8 VDC. Comparable to a 20-25 watt incandescent equivalent. Approximate size is 1.92in x .58in x 1.32in. Dim-able with variable voltage supply. CE and Rohs. Great for positive ground or negative ground vehicles, buses or scooters.

H10 female to H11 male Socket Converter/Extension. This extension will allow you to extend your factory wires down to your new fog lights. Or convert your existing H10 socket to an H11, without the need of splicing or re-wiring. Approx. 9.5" end to end. UL1015 #18 ,can handle up to 55w power.

9 Watt (per bulb) MCOB LED Ultra Bright Daytime Running Lights 12VDC. Very bright LED running lights with adjustable mounting brackets and bolts for easy installation. Metal frame makes for a long lasting durable running light (2 Pack). Available in 6000k white only. Perfect for any vehicle.

LED Spotlight, Daylight Headlight Wire Kit. Use this kit to install your L.E.D. headlights, spotlights, daylights in your car. Low voltage automotive, motorcycle, jet ski or snowmobile. Comes with 16 feet of 18 AWG stranded wire, inline fuse with 10 amp fuse, 2 quick connect connectors to attach to positive 12 Volt D.C. and ground wires. This kit is enough parts to provide 100 watts of power for one LED light circuit.

9 Watt Driving, Off Road, Work light Pair. 3, 3 Watt high power led's per light, 9 watt led per light comparable to a 70 watt incandescent bulb. spot light (30 degree viewing angle). 3.21 inches around and 2 inches wide. Sturdy metal design. Comes with metal mounting brackets. Comes in white 6000K. 10-30 Volt D.C. IP 67. Available only in 6000 K.

H3 25 Watt Fog Led Light. Uses PK22s base. Very bright comparable to a 160 watt incandescent light bulb uses only 25 watts of power. Length is 2.48" and .49" wide. 12 volt dc. Very nice heat sink to help the leds last longer. Up to 860 Lumen output. Up to 360 degree illumination. 120 Degree viewing angle for this running light. Very bright in a compact H3 driving lamp. CE and Rohs listed.

16 LED Driving Light 1 Pair 12 Volt DC. Each driving light has 16 LEDs. Uses .2 Amps at 12 volt DC only. Uses 3 watts of power comparable to a 15 to 20 watt light. This product measures 5.74 inches by 1.78 inches. The adhesive mount measures 2.76 inches by 1.30 inches and extends 1.76 inches. Approximate 25-35 degree viewing angle. Chrome plated.

Fog Light, H11, 3 Watt + 12 SMD (6 watts), 9 Watt bulb comparable to a 55 watt incandescent bulb. 12VDC, 120 viewing, long life up to 30,000 hours, available in white 6000K. 5730 SMD chip extremely powerful and small size. 270 lumen output side firing, 250 lumen output forward firing. This bulb is not dimmable. Has a lens in the top to make brighter. Compatible with: 894 H8 H9 H11

H3 25 SMD 1210 Fog/Daylight L.E.D. Light. 12 VDC. Uses PK22s base. 25 1210 Super bright S.M.D. "Surface Mount Device". Has 1 forward firing and 24 side firing LEDs, and only uses .09 A @ 13.8 VDC. About 1.2 Watts. Ony use for your fog light. Comparable to a 10 watt incandescent equivalent. 1 forward and 24 side firing LEDs. Available in white only. Very bright product. The maximum overall length is 1.875" that is from the top to bottom of the bulb. The width of the bulb not including round flange is .453". The round flange maximum diameter is .866". Approximate lumen output up to 175 lumens.

Fog, Running, Driving, H16 5202 L.E.D. Wide voltage 12-24 VDC or VAC. 300 lumens, Uses only 3.5 Wattage 30 watt output equivalency.. Lifespan up to 30,000 hours, 360 degree illumination, White 6000K, CE and Rohs listed.

The 8 Ultra-Bright Chrome Projector Automotive LED Puck Light is a great interior accent light. It throws cool blue color LED light where you want it. Each LED puck Light has 5 feet of wire and adhesive tape to make installing the puck lights a breeze. You just have to wire them in to your cars electrical system. The puck lights are great for limos, tucks, cars, 18 wheelers, tractors trailers anywhere there is 12 volts of power DC you can use the Chrome LED Puck Lights. 1 Pair. Includes mounting screws.

H13 18 5050 (3 Chip) LED Light Bulb. Great replacement never have to change your fog . 12 VDC. Available in white only. Only use for your fog light. This bulb has 3 forward firing and 15 side firing LEDs, for a higher brightness intensity. This LED measures from top to bottom 2.66in, with the LED diameter at .60in and the base diameter at 2.03in. Output around 325 lumen output. Comparable to a 25 to 34 watt incandescent bulb.

9005 HB3 Running LED Fog Lamp 18 SMT 5050 (3 Chip). 12 VDC. Available in white only. Great driving/fog light replacement in those hard to reach light fixtures. Ony use for your fog light. This bulb has 3 forward firing and 15 side firing LEDs, for a higher brightness intensity. This LED measures from top to bottom 2.32in with a width of 1.80 and a diameter of .60in. Compatible with: 9005 - H10 - 9040 - 9045 - HB3 Low beam 9006 - HB4 High beam

LED Day/Driving Light Adjustable. Operates @ 12 Volt DC. The unit is adjustable and low profile or thin body. Available in white only. Very thin body design. The unit is water proof, easy to install and uses super bright L.E.D.s. Package includes a pair (2) of driving lights. This product measures 4.30 inches by 1.15 inches with an adhesive mount that extends 0.58 inches and has a thickness of about 0.07 inches. The adhesive mount measures 3.30 inches by 0.97 inches. Chrome plated.

Fog, Running or driving led light. 18 SMD leds, 180 side lumen output, Wide voltage range 12-24 volts ac or dc. CE and Rohs listed. Long life up to 30,000 hours. Available in white 6000k. Uses only 3.2 Wattage 25-35 watt output equivalency. Durable, shock, vibration proof, instant On/Off. Monochromatic (pure) color, low heat generation, virtually unbreakable.

Use this externally mounted LED brake light. Has a red lens. Operates automotive voltage 12 Volts DC. Use this externally mounted LED decoreatebrake light. Has a red lens. Operates automotive voltage 12 Volts DC. The outter ring is RGB, slowly cycles through the colors, while the interior circle is only red and flashes 3 red leds through a cycle. You have no conrol of the flashing. 1 per package.

H3 L.E.D. Fog, Running, Driving, 12-24VDC. Has PK22s base. 120 viewing angle beam. Long life up to 30,000 hours. Available in white 6000k. Up to 56 watt incandescent equivalent. CE and Rohs listed. Made of metal materials to keep led's cooler, last longer, brighter. Having a shorter profile it makes it possible to install in smaller areas and still get the brightness desired. Connecting wire is 3" in length, end lug is .25" wide.

18 LED Daylight Driving Light with Remote Flasher. Comes in a pair. Chrome finish. Super bright LEDs. This LED comes equipped with a remote controller that allows flash or no flash of the led lights, lighter outlet plug, durable, plastic, clear lens, aluminum incasing, loose wires for easy installation, adjustable stand for mounting and a sticky adhesive on bottom of stand. Available in color changing RGB. Approximate size is 3.07in x .98in. Controller- 2.60in x .86in. Lighter plug- 3in x 1.46in x .68in.

Light Bulb. This LED Light will replace the 9004 or the 9007 series Fog/Daylight Running Light bulbs. 12 VDC, available in white only. Helps to repalce these hard to reach light bulbs. Ony use for your fog light. This bulb has 3 forward firing and 15 side firing LEDs, for a higher brightness intensity. This LED measures from top to bottom 3.14in, actual LED diameter is .59in and the base diameter is 1.65in. Available in white 6000K. CE and Rohs listed. Up to 400 Lumen output. 360 degree illumination. Comparable to a 35 to 45 Watt incandescent. Easy to remove the old light bulb and insert the new led bulb. Long life up to 30,000 hours. Please see extended warranty for further details.

LED Driving Day Fog Lights with Remote Sound Controller. 12 VDC. Remote controller allows the LED Lights to change to the music, basically a LED Light sound controller. The lights will change colors and brightness based on the sound. Sold as a pair. This product measures 4.38 inches by 1.54 inches by 1.22 inches. The adhesive mount extends 0.80 inches and measures 2.72 inches by 1.06 inches. The charger measures 4.22 inches by 1.54 inches with a thickness of 1.06 inches. Chrome plated.

Remote controlled driving lights 2 4 watt led headlights. Operates 12 volts dc, long life leds, CE and Rohs listed. Comes with wire harness and mounting hardware. long life up to 30, 000 hours. Includes remote. Use remote to turn on and off the driving lights. Remote Measures 2.5" tall, 1.5" wide with a 2.7" telescopic antenna. Please see Manual for the remote controls button placement. Using the function button you can make your lights flash, fade on and off, or turn the light on or off. Comes with double sticky adhesive to mount. Wires measure 35" in length.

880/881 H27 LED Headlight 9 to 40 Volts No Polarity. Works either positive ground or negative ground. From 9 to 40 volts non polarity. Uses H11 female socket. Up to 1.91 amps at 12 volts. Has a small fan to keep the led's cooler so they last longer. Approximately 23 watts for each bulb. Up to 2100 Lumens per bulb. Long life up to 30,000 hours. Available in White 6000K. Has about 4" of wire to connect the led headlights. Load equalizers maybe required. Warranty 1 year from date of purchase. Includes 2 bulbs per package. Compatible with: 862, 880, 880ST, 881, 884, 885, 886, 889, 890, 892, 893, 893ST, 894, 896, 898, 899. H11 female socket not included.

LED Driving Lights 1 Pair Low Profile. The kit includes 2 driving lights and a wires, angled bracket and mounting kit. Each driving light has 12 LEDs. The led face measures 4.21 inches by 1.75 inches with a thickness of about 1 inch. Chrome finish. The LED color is white 6000K.

H11 male to H16 female water proof harness. Use to convert your headlights or driving lights from H11 to H16 to use better headlights. CE and Rohs listed. Made with heavy duty wire for high power driving light applications. UL1015 #18 ,can handle up to 55w power.

H11 female Waterproof socket to H1 male waterpoof socket. CE and Rohs listed. Made of large diameter wire to handler larger power needs such as headlights. Harness is about 9.5 inches long. UL1015 #18 ,can handle up to 55w power.

H11 male waterproof connector to H1 female waterproof connector. Made of heavy duty wire for high power uses such as headlights and driving lights. Harness about 9 1/2 Inches long. UL 1015 #18 awg cable. Handles up to 55 watt of power.

9006 male water proof to h11 female waterproof harness. CE and Rohs listed. Made of heavy duty wire for high current applications. Great to change your headlight or adapt a different headlight to your automobile. About 9.5 inches long. UL1015 #18 ,can handle up to 55w power.

LED Driving Lights. Light has 5 high power leds. Chrome plating look. Durable, low profile, angle mounting brackets. Has double sided tape for easy installation. Easy hookup Red wire +12, grey to ground. 5 watts of power, comparable to a 45 watt driving light. Package includes two LED driving lights.

LED Fog light, 18 smd leds, 180 side firing lumens, 140 forward firing lumens. 12-24 VAC or VDC operation, long life up to 30,000 hours, low power, 120 degree viewing angled, 360 degree illumination. CE and Rohs listed, White 6000K

LED headlamp works either positive ground or negative ground. Wide voltage from 5 to 30 Volts AC or DC. Available White 6000K to 6500K or Warm White 2700K to 3300K. No polarity, Bi polarity, non polarized. Made with 16 2525 smd for super bright. The headlamp lights on both sides. Dual filament both a low and high beam. The low beam Lumen output is up to 1200 Lumens. The high beam is up to 1800 Lumens. Great for vintage and classic cars. Long life up to 30,000 hours. CE and Rohs certified. Made with aluminum to keep the led lamps cool so they can operate for a long life. The circuit board is constant current so the leds should not flicker. Available in White 6500k. Perfectly works with product 69854 is a 7" round semi-sealed housing and 68721 is a 5"x7" rectangle housing. Both these semi-sealed housings use the P43T bulb.

Converts from 12 Volt 4 Amp to 6 Volt 8 Amp. The features are 1. Synchronous rectification technology, the conversion efficiency more than 96%. 2. Internal resistance capacitor filter, withstand high temperature. 3. Almost no heat generated when operated. 4. Chip smart protection, anti-overheating, overcurrent protection. Use this to power your 6 volt powered devices from 12 Volts. Works both positive ground and negative ground vehicles, motorcycles and scooters. It is a good ideas also to put a power switch to turn off the device when not in use. It could be wired to your ignition line where power would be applied when the ignition switch is turned on. Operates from 10V to 35V input voltage. The output is regulated at .1V@6V. The output power is 48 Watts. The Transfer efficiency up to 96%. The Working temperature is -25?-85?. The converter has overheating protection at 150?. The no load current =0.35mA.

S25 18 Ultra Bright SMD LED Light Bulb. 3 forward firing Ultra Bright SMD LED's and 15 side firing Ultra Bright SMD LED's. Durable, shock, vibration proof, instant On/Off. Monochromatic pure color, low heat generation, virtually unbreakable. This LED measures from top to bottom 1.93 in and a diameter of .73 in. Available in super white 6000K, warm white 3000K, red, yellow, blue and green. 12 V DC. Uses only 3.5 Wattage 30 watt output equivalency. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W BA15D replaces 90 1004 1076 1142 2 1157 G18. CE and Rohs listed. Each 5050 LED emits about 15-20 lumens per chip, the bulb outputs up to 300 lumen output. This bulb fits 1953 Cessna 170 airplane.

1156 led bulb operates in a positive ground or negative ground from 6 to 12 volt AC or DC system. G18 S25 2.6 Watt L.E.D. bulb. Has 6 forward firing and 7 side firing LEDs. The life is up to 30,000 hours. Available in white 6000 Kelvin, warm white 3000 Kelvin, Red 625 nm Green 526 nm, Blue 464 nm& Yellow 594 nm. Available 1156 BA15S. Great bulb for tight fit, this small high power led is great for all applications, very bright up to 300 Lumen output in 360 degree illumination. This bulb will operate in classic old vintage antique cars positive earth, trucks and motorcycles 6 volt low voltage. This bulb is non polarity, no polarity you can use it in positive chassis and negative chassis cars, trucks an motorcycles. Comparable to a 25 to 30 watt incandescent, very small fits in tight bulb locations. CE and Rohs listed. Uses approximately 100mA @ 13.8 Volts.

Available in super white, warm white, red, yellow amber, green and blue. Approx .08 mA @ 12.8 Volt DC and 1 watt @ 12.8 VDC power . Equivalent to a 10 watt incandescent bulb. Up to 90 lumens. The bayonets are the same height, but with a dual contacts, please select BA15D under type. Long life up to 30,000 hours. The overall length is 1.25 inches and the diameter is .59 inches. This LED bulb is dimmable with a variable 12 VDC power supply. Fits most bow lights. The white is very bright. For 12 Volt systems that are negative ground. Great for airplanes, marine or recreational vehicle use. The white is created by a blue led with material added to the blue led to make the color changed to white or warm white. The white 6000k is brighter than the warm white 3000K by 5 to 10%. The led colors are created by the material used to create the led.

G18 13 5050 SMD (3 Chip), 12 VDC. Available in 1156 and BA15D base types. The color is super white. 13 5050 3 chip SMT are very bright in a very low profile package perfect for G18 applications. Approximate size is 1.64in (height) x .60in (diameter). 2 watt LED. 200 lumens output, compared approximately to a 20 watt incandescent bulb.

G18 LED Light. 8 LEDs 8 forward firing. Available in super white, red, yellow, green and blue. 12 VDC. Single circuit BA15S base and dual circuit BA15D base. 20mA@12VDC. 1.35 Inches in overall length and 0.75 Inches in width. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W BA15D replaces 90 1004 1076 1142

6 LED Light Bulb. Available in white only. Available in 1156, 1157 and BA15D. 12 Volt DC @ .72 Watts. This product measures approximately 1.28 inches by 0.72 inches.

3 LED Light Bulb. Very low profile LED Light. Great for hard to change light bulbs. Available in white only. Uses .25 Watts at 12 VDC. This LED measures approximately 1.25 inches by 0.60 inches. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 #89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W T25 T-25 1016 1034 1130 1152 1157 1493 2057 2357 2397 7528 3496 BA15D replaces #90 #1004 #1076 #1142 CE and Rohs certified. Forward firing leds. Up to 30 Lumen output. Comparable 4 to 14 watt incandescent. 45 degree viewing angle.

1158 Miniature LED Bulb for old vintage and classic cars. 2 filament or brightness levels. For Negative ground vehicles. Operates from 6 to 12 volts DC. 360 degree illumination. This is a BA15D base product. Long life up to 30, 000 hours. Latest technology 5730 SMD LED chips for very bright and long life. The bulb fits the outline of a normal incandescent bulb. UP to 270 lumen output for tail light, up to 320 Lumens for brake light. 1158 for older negative chassis 6 to 12 volt cars or motorcycles, tractors. The difference between a 1157 and 1158. The 1157 the bayonets are offset while the 1158 are the same height. The diameter of the base is 15mm so it will fit your fixture if 1158 style. Long life up to 30,000 hours. Comparable to a 25 Watt to 35 Watt incandescent light bulb. If the tail light is brighter than the brake light please rotate the bulb 180 degrees. CE and Rohs.

G18 1156 17 QTY 5730 SMD 12V DC/AC. This led bulb is bright, has 17 pcs of 5730 SMD leds. A nice heatsink enclosure keeps leds cooler for long life, very compact. Operates 12V AC or DC non polarity. Non polarity for model T and world war II before and after the bulb with work. Just for a normal 12V voltage or voltages nothing needs to be done just remove old bulb and insert new bulb. Long life. Available in White 6000K. Up to 250 lumen output, 360 degree illumination. Each LED 1/2 watt. This light is bipolar so it can operate negative and positive polarity. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W. Uses about 250 mA @ 12 VDC.

81 LED Bulb 6 Volt Positive Chassis or Negative Chassis Miniature bulb. This bulb will work on AC or DC voltage. The maximum bulb length is 1.24 inches and the maximum diameter is is .75 inches. This will fit the small size of a #81 light bulb. BA15S single contact. G6 single contact bayonet LED. C-6, C-2R filament design compatible, single filament Uses only 1 Watt at 6 volts. Uses very low power. The profile is very small to match the profile of the #63 bulb. The light output is up to 90 Lumens the #63 bulb has a rated output of 3 candle power CP, the LED is up to 6 candle power so about twice as bright as stock light bulb. This bulb is available in White 6000K, Warm White 3000K, Red 625 nm, Green 526 nm, Blue 464 nm & Yellow 594 nm. Long life up to 30,000 hours.

S25 3 Watt LED. Very Bright output up to 300 lumens, comparable to a 25 watt incandescent bulb. Concave lens for good light distribution. Concave lens is perfect for applications that need the beam angle narrow. 12 Volt DC for negative ground. Great for automotive use in tail lights, RV interior and exterior lighting, and boat interior lighting. Please make sure to measure your current bulb to ensure this will fit in your receptacle. Made with Aluminium to keep the led cooler. Great metal heat sink for long life rated up to 30,000 hours. Available in White (6000K), Warm White (3000K), Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). Viewing angle 30 degrees.

G18 3 1/2 Watt High Power LEDs. Very Low profile for a 1.5 Watt G18 LED Light Bulb. Available in white only. Available bases BA15D, and BA15S (1156). 12 Volt DC . This LED measures approximately 1.08 inches by 0.66 inches by 0.60 inches. 1156 replaces BA15S T25 T-25 1073 1093 1141 1159 1259 1295 1383 1459 1619 1651 1680 2056 3496 5007 5008 7008 7506 7806 7527 1156 1759 3497 1156-18W 67 89 97 1156 12821 P21W LOW 61 63 67 #67 69 71 81 #89 97 98 303 623 1003 1155 1247 1251 3497 5007 5008 12821 P21W T25 T-25 1016 1034 1130 1152 1157 1493 2057 2357 2397 7528 3496 BA15D replaces #90 #1004 #1076 #1142

82 LED Bulb. BA15D Base. 6 Volt Positive Ground or 6 Volt Negative Ground. Up to 200 Lumen output. Up to 15 Candle Power. The maximum length is 1.25 inches and the maximum diameter is .75 inches. Comparable to a 10 to 25 Watt incandescent bulb. The L.E.D. bulb C-6 filament design. Single Filament. Uses up to 2 Watts @ 6 Volts. The base is BA15D with even bayonets. The lamp only has one brightness level. The bulb is dim-able using variable voltage supply such as dashboard knob. Great for license plate, turn, tail, brake, dome, dashboard, instrument panel lamps. The LED color is created by the material of the LED so it looks real nice monochromatic. The available colors are White 6000K, Warm White 3000K, Red 626nm, Green 526nm, Blue 646nm and Yellow 594nm. The old light bulbs were painted. Very low profile to fit Ford Model A cowl light. Long life up to 30,000 hours.

BAU15S LED Bulb. Operates from 7-24V AC-DC Non Polarity. Use this bulb for vehicles, classic cars or motorcycles. The base is BAU15S. The diameter of the base is 15mm. The base is a single contact, single filament. The bayonets are V shaped, about 150 degrees spaced apart. Operates from 7 to 24 Volts AC or DC. Available white 6000K. Up to 250 lumen output. Comparable to a 25 to 35 Watt incandescent light bulb. Each 5730 SMD is up to 1/2 watt of output power. Operates in both negative ground and positive ground. Long life up to 30,000 hours. 360 degree viewing angle. Great for RV's, boats and motorcycles. Small profile allows the led bulb to fit in the same space as a incandescent bulb. Made of metallic metal to keep the led's cooler so they last longer. CE and Rohs. Compatible with: ry10w

LED Compatible flasher. The LED compatible flasher is for 7 to 24 Volts DC. Maximum voltage 31 volts. Negative ground vehicles or motorcycles. This 2 prong round flasher can handle up to 150 Watts of led or incandescence bulbs. 1 to 6 LED Bulbs or incandescent bulbs. Each incandescent bulb is around 21 Watts. The flasher will flash between 60 and 120 Hz. The flasher can power from 0.1 Watt to 150 Watts of lighting, .02A-20A. Operating Voltage from 7 Volts DC to 31 Volts DC. The duty ratio of this flasher can range from 30% to 70%. The operating temperature from -40C to +80C. The flashers life time is up to 400 hours of flashing time. The flashers body is round. Plug and play disconnect power remove old flasher and install new flasher reconnect power. Very easy to eliminate hyper flashing by replacing your old flasher with this LED compatible flasher.

LED compatible CF14 JL-02 EP35 12 volt DC flasher, maximum 150 watt. Can use incandescent or LED bulbs. Power from .1 Watt to maximum wattage 150 Watt. Voltage range 11 to 15 Volts DC. Please do not exceed maximum wattage or voltage. CE and Rohs listed. Long life up to 400 hours flashing. See product detail for warranty period. Includes 1 item per package. Up to 13 amps max. This relay saves time and money by not having to install load equalizers with LED bulbs. The three terminals are B, E, L. The flasher can operate from .02 Amps to 20 Amps. This flasher will eliminate hyper flashing or bulb out error. Flasher complies with or exceeds SAE 100-hour test. The flasher passes FMVSS: J945, J590 certification.

LED compatible 12 volt DC flasher CF13 JL-02 EP34. Power from .1 Watt to maximum wattage 150 Watt. Voltage range 11 to 15 Volts DC. CE and Rohs listed. Long life up to 400 hours flashing. See product detail for warranty period. Includes 1 item per package. This relay saves time and money by not having to install load equalizers with LED bulbs. can use either incandescent or LED bulbs. Up to 13 amps max. The three terminals are 31, 49, 49a. The flasher can provide from .02 Amps to 20 Amps of power for the 1 to 6 lamps. Each lamp can be either led or incandescent. Usually each incandescent bulbs use around 21 watts of power. This flasher complies with or exceeds SAE 100-hour test. The flasher is certified for FMVSS: This flash will click like your old flasher. Working temperature -40C to +80C. Flasher frequency 60-120 Hz. This flasher life up to 400 hours. Size 30mmx30mmx30mm.

LED compatible 12 volt DC flasher, maximum 150 watt. Can use incandescent or LED bulbs. Please do not exceed maximum wattage. CE and Rohs listed. Long life up to 400 hours. See product detail for warranty period. Includes 1 item per package. Up to 13 amps max. This relay saves time and money by not having to install load equalizers with LED bulbs. The 5 terminals are B, E, H, I, L. Dimensions are 2" height from bottom of contacts to top and 1 3/8" width and 1 3/8" deep. Compatible with: 2014 Ford F150 1/2 Ton EP27L CEC EF27 NAPA EP27 CARQUEST FSH7127 TRIDON EP27 LITTLEFUSE FLR727 TRUCK LITE 97283 SMP EFL4 SMP EFL14 SMP EFL17 Motorcraft SF632 Flasher Directional

LED compatible 12 volt DC flasher. Can use incandescent or LED bulbs.Long life; 400 hours. Please do not exceed maximum wattage. CE and Rohs listed. See product detail for warranty period. Includes 1 item per package. Up to 13 amps max. This relay saves time and money by not having to install load equalizers with LED bulbs. Maximum 150 watts. The two terminals are X, L. This flasher is solid state so it does not click like your old flasher. Compatible with: EP 37 EP-37 EP37 CEC EF40 NAPA EP37 CARQUEST FSH7216 EATON BUSSMAN 763 PETERSEN PM573 TRIDON EP37 LITTLEFUSE FLR763 GROTE 44690 TRUCK LITE 182 VELVAC 091212 EP50

LED Flasher 2 pin for motorcycles, scooters, golf cart, go carts and Ebikes. This flasher is designed for motorcycles that have upgraded to LED lighting.This flasher relay will decode or eliminate hyper flashing due to LED lighting. This flasher can operate for 400 hours continues flashing. The flasher can handle maximum up to 65 Watts of lamps per side. The lamps can be either LED or incandescent or both. The flasher will flash from 60 to 120 times per second. The duty cycle is from 30% to 70% or 85 +-10 c/min. The lamp Wattage can be from 1 Watt to 65 Watts maximum power. The operating voltage is from 8 volts DC to 16 Volts DC. The rated voltage is 12 Volts DC. The operating temperature is from -40C to +80C. The flasher is CE and Rohs listed. The two terminals are L for load and + for the positive battery terminal. Please hook up your anode of your led bulb to the L load pin of the flasher.

LED compatible 12 volt DC flasher, maximum 150 watt. Can use incandescent or LED bulbs. Please do not exceed maximum wattage. CE and Rohs listed. Long life up to 400 hours. See product detail for warranty period. Includes 1 item per package. Up to 13 amps max. This relay saves time and money by not having to install load equalizers with LED bulbs. The 4 terminals are L, S, -, +. To connect EP39, + connected to battery - connected to ground L connected to load anode of led or either side of incandescent bulb S = high 12v flashes, N.C. or low no flash Compatible with: CEC EF29 NAPA EP29 CARQUEST FSH6051 EATON BUSSMAN 762 TRIDON EP29 LITTLEFUSE FLR762 GROTE 44120 SMP EFL6 EP 29L

Flasher Module Controller for LED lights. Operates on 12-24V. Nice and compact flasher design, as well as waterproof (Rated IP65). Very simple installation; simply tap OUT to the application first, then tap the IN to the power. With this being a universal flasher, it works great for cars, trucks, motorcycles, armored vehicles, electric bicycles, and much more. Has approximately 5" of wire on both sides. Approximately 2" long by 0.6" deep by 1.1" wide. The module allows you to convert the brake lamp to quickly strobe for 3 times, then flash for 3 times, and then light up constantly, allowing you to better alert vehicles behind you. Includes a 3M sticky strip for mounting. Improve safety warnings. 2 Patterns of blinking. Blinks fast 4 times then blinks slow 4 times, after blinking the flasher stays on. Great for automobiles, electric bicycles, tanks, armored vehicles.

Use this flasher to eliminate hyper flash in motorcycle that use with 7 or 8 pin flasher. This relay maximum load is 65 Watts, this is the maximum load for one side since only one side lights at a time. This flasher will decode or eliminate hyper flash. So you can use both LED or incandescent bulbs. The rated Wattage is up to 65 Watts. Plug and play, turn off power, remove old flasher relay, install new flasher, turn on power.

LED flasher for motorcycles. Up to 100 Watts to power multiple LED or incandescent light bulbs. Very easy to install, disconnect power, remove old flasher, install new flasher, reconnect power. Plug and play L.E.D. compatible flasher. Rated for 12 volt DC. The relay blinker will operate from 8 volts DC to 16 volts DC. Specifically designed to decode or eliminate hyper flashing due to use LED lights. The relay blinker is CE and Rohs listed. The flasher has a rated flashing life 400 hours. The led flasher duty cycle is from 30% to 70% 85+-10 c/min. The flasher has three terminals. The first terminal goes to the positive battery terminal. The second terminal goes to ground. The third terminal goes to the turn signal level common terminal also called the winker switch. The load can be either LED or incandescent.

LED Flasher compatible Up to max 65W power to drive the led or incandescent light bulbs. The max wattage is calculated that only one side will be lit so 42W plus the pilot bulb 3.7W is about 45.7W rated and the maximum is up to 65W. This flasher will decode hyper flashing due to LED bulbs. The led flasher has 4 terminals. The first terminal is for constant power the battery. The second terminal is for the ignition switch to enable and disable the flasher. The third terminal is for the pilot dashboard indicator light. The 4th terminal connect to your turn signal level common terminal. The turn signal level is called the winker switch. Please be careful when you connect a LED turn signal bulb that you must connect the anode of the LED to the terminal for the turn signal lever. The other terminal for the turn signal level goes the anode of the other turn signal lamp.

LED compatible 12 volt DC flasher, maximum 150 watt. Fits only model EP28 flashers. Please do not exceed maximum wattage. CE and Rohs listed. Long life up to 400 hours. See product detail for warranty period. Includes 1 item per package. This relay saves time and money by not having to install load equalizers with LED bulbs. can use incandescent or LED bulbs. Up to 13 amps max. The three terminals are L, -, +. Replaces the following flashers: EP 27 EP-27 CEC EF28 NAPA EP28 CARQUEST FSH6136 EATON BUSSMAN 761 TRIDON EP28 LITTLEFUSE FLR761 SMP EFL5

6 volt led flasher negative ground. This flasher operates negative ground up to 150 Watt's. This flasher is rated from 5 to 8 volts. The flasher eliminates hyper flashing so no load equalizers required. After market turn signal controllers can cause load equalization issues. After installation you still have issues please install load equalizers. The rated flasher flashing time is 400 hours. The flasher relay clicks like a real old time flasher so you can hear that you have your flasher on. The duty cycle ranges from 30% to 70%. Please connect your anode of your LED to the L terminal. Please connect your cathode of your LED to ground. The anode is the positive terminal of the led if you are not sure please hook your led up to your battery to see which side is the anode and which side is the cathode. The rated load is from 1 amp to 20 amps. The rated wattage is up to 150 Watts.

Replaces 81980-50030 066500-4650. The flasher does not hyper flash due to led lights. The flasher can power up to 150 watts of bulbs. The rated voltage is from 11 to 15 volts DC. The rated voltage drop is 800 mV. This voltage drop is due to the solid state electronics versus zero for a mechanical flasher relay. This relay is plug and play. Easy to remove old flasher and then insert the new flasher and you are set. Now you can upgrade your lights with led lights and not have hyper flash condition. CE and Rohs. Compatible with: CF18 LM449 81980-50030, 81980-53010, 81980-02030, 81980-34020, 066500-4650 Lexus

12 Volt DC flasher LED compatible for vehicles, scooters and motorcycles. The flasher operates at 12 volt DC 24 Watts max. Use this flasher with only led bulbs that are less than 24 Watts total power. The flasher can handle up to 24 watts. This flasher has two 16awg gauge stranded wires about 6 to inches long. Please connect one side to the source plus voltage and the other side to the anode of a led that the cathode goes to the common ground. The rated voltage is 11 to 15 Volts. Voltage drop at rated current is 500mV. Time to first flash is less than 1.5 seconds. Approximately 60 to 120 flashes per minute. Duty cycle 35% to 75%. The black wire is load output. The red wire is power input. The approximate size is 1.27" long, by 0.66" tall, by 0.66" wide.

LED compatible flasher for 12 Volt negative ground vehicles. Has 3 terminals, Load, Pilot and X for positive 12 Volt input and a pigtail wire for ground. Can handle up to 120 Watts either led or incandescent bulbs. Contact L is for the load. Contact X is for the +12V input. P is for the pilot light. The flasher self adjusts the output for the load it has. The flasher is rated for 400 hours flashing time. The standby current is 20mA. The operating voltage is from 11 to 15 volts. Time to first flash is less the 1.5 seconds. The duty cycle is 30 to 75 %. The operating temperature is -25F to 140F. Approximate size 1.313" width, 1.422" height The pigtail wire length 7.5". Please use a 20amp fuse for the input X terminal. 60 to 120 flashes per minute. CE and Rohs.

LED Flasher 12 volt D. Long life 30,000 hours. 2 Terminal, 12 Volt DC. Up to 24 Watt. Compatible with: G215-XU

Winker, Flasher, 12 Volt to 24 Volt. Comes in three versions, Always Flashing, Flash Five Times Then Long Light, Fast Flash 4 Times, Slow Flash 4 Times, Then Long Light.

This universal led flasher will work negative ground vehicles, motorcycles and scooters. Operates from 6 to 15 Volts. Included are 7" of wire and quick disconnect crimps for easy installation. Flashes 60 times a minute. The load is from .5 Watt up to 20 Watt for led bulbs only. Please see diagram. CE and Rohs.

12 Volt LED compatible flasher for 12 Volt positive ground vehicles, motorcycles or scooters. The rated voltage is from 11 to 15 Volts. Has 3 contacts plus a pigtail wire. The 3 contacts are input X, which will make the flasher flash if low control contact. Contact L which will connect to the load which could be either incandescent or led bulb and if a non polarized led bulb would be the cathode. The contact P for Pilot light which will connect to the pilot light which could be either a incandescent or led. The pigtail wire which connects to the positive ground chassis. The flasher rated load is up to 120 Watts. The flasher can work with incandescent or led or a combination of both. This LED compatible flasher will fix your hyper flashing. The flasher has rated life up to 400 hours. The standby current is 20 mA. 60 to 120 flashes per minute. Lamp rated amperage .1 to 20 Amps self adjusting to lamp draw.

CF LED flasher works either 12 volt or 24 volt AC or DC non polarity. The flasher has 3 pins. The flasher works either with incandescent bulbs or led bulbs or both. The flasher eliminates hyper flashing or load equalizers. The flasher rated load in up to 120 Watts. The terminals are labeled "B", "L" and "E". The approximate terminal width is 0.250" and the approximate terminal length is 0.4". The "B" terminal stands for Battery and should be connected to the battery. The "L" stands for Load should be connected to the load. The "E" terminal connected to ground. The flasher has a audible click. The flash rate is 60 to 120 flashes per minute. The duty cycle is 30% to 75%. The flasher operates from 10 Volts to 24 Volts. The approximate size of the flasher is 1.04" width by 1.30" tall. CE and Rohs.

Flasher LED 6 Volt Positive Ground 3 Terminal for 6 Volt positive chassis. LED flasher for vintage and classic cars and motorcycles. This flasher is LED compatible so you can use led's or incandescent bulbs or a combination of both for the turn signal bulbs. The Pilot light bulb can be either incandescent or led. The flasher creates real clicking sounds like an old flasher. The flasher duty cycle is from 30% to 70%. The flasher rated load can handle up to 6 bulbs or 120 watts. The operating temperature -25F to +140F. The lamp rating should be from .1 Amp to 20 Amps. The rated voltage is from 5 to 8 volts can operate up to 8 volts. Voltage drop is rated at 500mv. The flasher will fit a standard 3 Pin female relay flasher socket. The shell is made of plastic for rugged long life. The flasher is self adjusting lamp amperage draw from .1 Amp to 20 Amps.

EFL3 LED compatible flasher. The flasher will audible click when be operated. Since it is a led compatible flasher no need to use load equalizers. 12 Volt DC.

FLL050 LED Compatible Flasher 2 Pin 12VDC. Designed for motorcycles. Operates 12 Volt DC negative ground. Flasher has a audible click when in use.

This universal led flasher will work positive ground vehicles, motorcycles and scooters. Operates from 6 to 15 Volts. Included are 7" of wire and quick disconnect crimps for easy installation. Flashes 60 times a minute. The load is from .5 Watt up to 20 Watt for led bulbs only. Please see diagram. CE and Rohs.

FLL011 LED Compatible Flasher 2 Pin Plus Pigtail 12 VDC. This flasher has 2 contacts plus a wire that has a terminal to connect the flasher. This flasher will audible click when activated. Operates 12 Volt DC for negative ground vehicles, motorcycles and scooters.

FLL55F LED Compatible Flasher 12VDC 2 Contact. Eliminates hyper flashing. No need to use led load equalizers. Operates 12VDC for negative ground motorcycles and scooters.

LED Flasher 13.8 Volts, 12.5 Amps, 150 Watts rated total power. Two pin. CE and Rohs. Eliminates hyper-flashing or load equalizers. Works with either incandescent or led bulbs or a combination of both. The teminal width is approximately 0.250" and the terminal length is approximately 0.40". The flasher contact labels are "L" and "+". The width of the flasher is approximately 1.194". The height of the flasher is approximately 1.526". Known as CF12ANL-01. Please connect +12V to the "+" terminal. Connect one end of your load either incandescent or LED to the "L" terminal. Connect the other end of the load incandescent or LED to the ground terminal. The flasher will flash with two terminals. The flasher flashes approximately 60 to 120 flashes per second. 30% to 70% approximate duty cycle. Time to first flash less than 1.5 seconds. The shell is made of plastic material.

EFL2 2 Pin led compatible flasher. Flasher makes a tick noise when flashing. Flasher can operate both incandescent and led bulbs at the same time. No need to install load equalizers when using this flasher. 12 Volt DC.

P15D-25-3 LED Headlight. Operates 12 Volts non polarity either Negative ground or Positive ground cars, trucks and tractors. The lamp uses 60 smd leds. The total lumen output is 950. Long life up to 30,000 hours. The bulb is about the same size to your current bulb you should not have any installation issues. The leds are aligned for the greatest amount of led light focused on your reflector. The lamp is dim-able using a variable voltage source. Great for old classic and vintage cars, trucks and motorcycles. The bulb is dual filament so has two brightness levels low and high beam. Available in ultra white 6000k and warm white 3000k. Extended warranty, please see bottom of the page for more details. Eurostyle ULtra White. Uses about 7.5 Watts@13.8 Volts. Maximum overall length is 1.944 inches. The maximum diameter is 1.058". Compatible with: BMW M5 Headlight

H4 6 Volt LED Headlight. Works either positive or negative ground. p43t Base for classic and vintage vehicles. This bulb operates from 8V to 30 volts AC. Has the 6 Volt running light feature. Great for old vehicles that are positive ground or negative ground. The bulb can be adjusted 360 degree's using allen wrench. The Lumen output for high beam is up to 1,800 Lumens. The Lumen output for low beam is up to 1200 Lumens. Operating life up to 30,000 hours. Up to 17W led output power which is comparable to 150 watt incandescent bulb The low beam is covered with anti dazzle protection for the on coming driver. The are 2 led's on each side which 2 led's are used for low beam and two led's are used for high beam. Available in White 6000K only. Package comes in a pair. Available in white 6000K. CE and Rohs.

This H11 H8 880 881 Male Adapter to #18 awg wires. high efficient, heavy duty and heat resistant. Nylon female plug can withstand up to 1200 Fahrenheit. H11/H8 or 880/890 lamp connector for 12V use only. Up to 55 watts power per harness. Harness is approximately 7.75 inches long. Made with #18 awg stranded wiring to handle the high powered driving lights. Great for fog, driving or headlights. Water proof PVC and nylon plastic adapter and 6.5 inches #18 awg wiring. H11 H8 880 881 male are interchangeable, they all fit the same light bar, or cube light, fog light, headlight. Two insulation displacement connectors are included to connect the wire to the existing automobile harness with minimal damage to the automobile harness. Approximately 7.75" in overall length, with the wires being 6.5". Overall width of connector end is approximately 1.07", with the plug being 0.66".

Headlight bulb 6 Volt Positive Ground or 6 Volt Negative Ground. 6V AC or DC. Up to 650 Lumen high beam and up to 510 Lumen for low beam. This headlight bulb is up to 50 candle power CP for high beam. Up to 40 candle power CP for low beam. Dual filament design. Designed for reflector headlights since most of the leds are side firing directly into the reflector. The bulb has some forward firing leds to make it brighter. This LED bulb is designed for early vintage Ford Model T headlight and Ford Model A headlight. Long life up to 30,000 hours. Plug and play remove the old incandescent bulb and replace with LED bulb. The LED uses less power than a incandescent bulb so it is easier on the wiring of the older vehicles. This headlight bulb uses approximately .112 Amp @ 6.9 volts for low beam. This led headlamp bulb uses around .490 amp @ 6.9 volts for hi beam. The bulb comes in White 6000K and Warm white 3000K.

H10 female to H11 male Socket Converter/Extension. This extension will allow you to extend your factory wires down to your new fog lights. Or convert your existing H10 socket to an H11, without the need of splicing or re-wiring. Approx. 9.5" end to end. UL1015 #18 ,can handle up to 55w power.

P15D-30 LED Headlight. Operates from 6 to 30 volts non polarity. Works either positive ground or negative ground. Dual filament both low beam and high beam. Forward firing so all your light illuminates in front of you. Made with 1860 LED chip to illuminate your road. Available in White 6500K or Warm White 3000K. The diameter is approximately 1.06". The length is approximately 2.51". Since the bulb has a built in lens no need to reflect light off your fixture. Full brightness from 5.7 to 30 volts. Comes with a Allen wrench so you can adjust the focus beam base on your socket orientation. CE and Rohs.

Forward Firing LED Headlight. 6 to 30 volts non polarity works either positive ground or negative ground. Works for both 6 Volt and 12 Volt vehicles. The LED chip is 1860 for very bright forward firing illumination. This is a focused beam. The diameter is approximately 1.06". The length is approximately 2.51". Available in White 6500K or Warm White 3000K. Up to 1500 Lumens for the high beam. Up to 1200 Lumens for the low beam. Comes with Allen wrench so you can adjust the beam. This bulb has built in lens so it does not have to reflect off the lens. Full brightness from 5.7 to 30 volts. Comes with a Allen wrench to you can adjust the beam depending on the orientation of your socket. CE and Rohs. compatible with: 1916-1936 Chevrolet trucks and cars.

Semi Sealed 7" Round Crystal Headlight Fixture with parking bulb 5 Watt. This fixture you can install your own H4 p43t bulb socket. 7" round fits standard 7" round fixtures. Has a parking bulb that you can use for your turn signal, running light or leave it not connected. The parking bulb using a 194 T10 wedge bulb. You can install your own bulbs led or incandescent H4 for the driving and 194 for the parking bulbs. The fixture is DOT SAE rated. Left hand driving for USA. This product is a NCNRNW Non Cancelable, Non Returnable, No Warranty product because the product could be damaged when installing. CE and Rohs. Comes in a pair. Compatible with: 6012, 6014, 6015,6016, H6014

LED Headlight up to 40 Watts. Operates 9 to 32 Volts. Made with Seoul CSP. Single beam uses 6 chips, Dual beam Hi/Lo uses 12 chips. The overall outline of the headlight is small so it will fit most automobiles. Each headlight outputs up to 4,000 Lumens total up to 8,000 for the pair. The single beam will have 6 Seoul CSP chips while the dual beam wil have 12 Seoul CSP chips. Each filament has 3 CSP chips that are about the same size as the original filaments. Easy DIY to remove old incandescent or halogen bulb and insert led headlamp. The led uses 1/8 the power and is up to 3 times as bright. The led light decay is much slower than a incandescent light bulb. These headlights are exact same location as your filament so the aligment is perfect for reflector or projector lens headlights. CE, Rohs, DOT, ECE approved. Very small profile to the headlamp will fit most applications.

p45t LED Headlight 6 volt. Up to 650 Lumen output or 60 CP. Dual filament high and low beam. Made with 5730 smd leds for long life. Rohs and CE listed. Designed for easy installation, just remove old headlight and insert new headlight. Works both 6 volt positive ground and 6 volt negative ground. Great for old classic and vintage automobiles, motorcycles and tractors. Available in white 6000K and warm white 3000K. Long life up to 30,000 hours. Comparable to a 45 to 55 watt incandescent bulb. The maximum overall length is 1.944 inches. The maximum diameter is .760 inches. The pin out as follows when looking at the connector from the rear. The left most contact is ground. The center contact is low beam. The right most connector is high beam. This lamp will fit a standard H4 HB2 9003 3 prong female Socket connector such as part number 34265.

L.E.D. Headlight 5.75" Round. Has High and low beam. Made for motorcycles. D.O.T. approved for street use. One headlight per package. 12 VDC. Up to 2400 Lumen output.

9004 LED Headlight 9 to 40 Volts No Polarity 12000 LM Pair. Works either positive ground or negative ground. Up to 6000 Lumens for the high beam. Uses about 1.91 Amps at 12 Volts. Up to 23 LED Watts. Comparable to a 55 to 65 Watt Halogen bulb. Available in White 6000K. This bulb is not dimmable due to the wide voltage. Wide voltage of 9 to 40 volts. The led bulbs are no polarity. These led bulbs do not have load equalization built in, load equalizers may be required. 2 Year warranty.

LED Headlight Load Equalizer works from 6 Volt to 12 Volt classic and vintage cars and motorcycles. Works either positive ground or negative ground. Please use a load equalizers for your low beam, one per side if your headlights are not working properly after installation. Sometimes after upgrading the older car electrical system does not recognize the new technology. Since led headlights use 80% less power, sometimes load equalizers are needed. Please connect the load equalizer in parallel with the low beam circuit. To connect parallel means one end of goes to the chassis and the other end connects to your low beam. Please use one per the left headlight and right side headlight. Included are insulation displacement crimps IDC. The IDC are easy to install using pliers and easy to remove. Recommended to install to the metal of the car to help dissipate the heat.

H7/H18 LED Headlight 9 to 40 Volts No Polarity. Operates either positive ground or negative ground. Up to 4000 Lumens per headlight bulb. Each headlight bulb uses 13 Watts. Maximum voltage 45 volts. The led headlights can operate from 9 to 40 volts no polarity. Up to 30,000 hours life. Available in White 6000K. Uses about 1.25A at 12 volts. 2 year warranty. Comparable to a 45 to 55 Watt halogen bulb. This bulb may require led load equalizers.

H3 LED Headlight DC 9 to 40 Volts. Up to 1700 Lumens per bulb. Works only negative ground. Uses about 1.25A at 12 volts. 15 LED watts of power per bulb. Operates from 9 to 40 volts DC. This bulb is not dimmable due to the wide voltage range. Up to 30,000 hours life. Available in White 6000K. Comparable to a 45 to 55 Watt halogen light bulb. This bulb may require load equalizers. 45 volts is the Maximum voltage. Please see warranty details below. Includes two bulbs per package.

H13 LED Headlight 9 to 40 Volts No Polarity 12000 LM Pair. Works either positive ground or negative ground from 9 to 40 volts. Up to 6000 Lumens per bulb. This bulb is not dimmable due to the wide voltage. Up to 30,000 hour life. These led bulbs do not have load equalizers. Load equalizers may be required to make led headlight bulbs operate correctly. 2 year warranty.

880/881 H27 LED Headlight 9 to 40 Volts No Polarity. Works either positive ground or negative ground. From 9 to 40 volts non polarity. Uses H11 female socket. Up to 1.91 amps at 12 volts. Has a small fan to keep the led's cooler so they last longer. Approximately 23 watts for each bulb. Up to 2100 Lumens per bulb. Long life up to 30,000 hours. Available in White 6000K. Has about 4" of wire to connect the led headlights. Load equalizers maybe required. Warranty 1 year from date of purchase. Includes 2 bulbs per package. Compatible with: 862, 880, 880ST, 881, 884, 885, 886, 889, 890, 892, 893, 893ST, 894, 896, 898, 899. H11 female socket not included.

9006/HB4 LED Headlight 9 to 40 Volts No Polarity. Works either positive ground or negative ground. Up to 6,0000 Lumens per bulb. Uses about 23 watts. Power consumption if 1.91 amps at 12 volts. Works from 9 to 40 volts. Long life up to 30,000 hours. Maximum 45 volts. Load equalization maybe required. 2 year warranty. Includes two bulbs per package.

H8 H9 H11 H16 LED Headlight 9 to 40 Volts No Polarity. Up to 12,000 Lumens per pair. Operates either positive ground or negative ground. Wide voltage from 9 to 40 volts no polarity. This bulb is not dimmable due to the wide voltage. Up to 6000 Lumens per bulb. Up to 23 led watts per pair. Each bulb uses 1.91A at 12 volts. Comparable of a 45 to 55 halogen bulb. Single filament. This bulb uses a H11 female socket.

T19 P15D-25-1 base led headlight. Up to 600 Lumen output. Dual filament Low and high beam. Long life up to 30,000 hours. The leds are optically aligned for best led light output using your reflective fixture. Please always clean the fixture when installing led light bulb. Comparable a 25 to 35 Watt halogen or incandescent bulb. The base is T19 P15D-25-1 base. This bulb operates either AC or DC. Operates at 6 volts, higher voltage with cause this bulb to fail. The bulb can operate up to 7.0 volts. Works either positive chassis or negative chassis. The M.O.L. maximum overall length is 1.976" and the M.O.D. maximum overall diameter is .747" not including the base diameter. CE and Rohs. Compatible with: p15d-25-1 PX15d H6 h6m P15D Honda TL125 125S 250 C105T 110 CT70 90 Honda 1970 mini trail Honda vintage mini trail 10-527-84114-09-xx

6 Volt P15D-25-3 LED Headlight dual filament. Works either 6V positive ground or 6V negative ground. Up to 950 Lumens for the high beam. Up to 700 Lumen for the low beam. The total length from contact to top of the bulb is 1.944". The approximate diameter is 1.058". Dim-able with a variable voltage source. Long life up to 30,000 hours. This bulb will use up to 90% less power than your current incandescent or halogen bulb. The base is 15mm diameter base has a ring approximately 25mm. On the ring are three tabs spaced 120 degree apart. The led's are optically aligned for the best output possible. Your generator or alternator will be happy to have to work less to light up the new headlamps. Available in white 6000K. Uses about 1 Amp @ 6.3 Volts. CE and Rohs. Maximum overall length is 1.944 inches. The maximum diameter is 1.058". 6.9 Maximum Voltage.

H11 male to H16 female water proof harness. Use to convert your headlights or driving lights from H11 to H16 to use better headlights. CE and Rohs listed. Made with heavy duty wire for high power driving light applications. UL1015 #18 ,can handle up to 55w power.

H11 female Waterproof socket to H1 male waterpoof socket. CE and Rohs listed. Made of large diameter wire to handler larger power needs such as headlights. Harness is about 9.5 inches long. UL1015 #18 ,can handle up to 55w power.

Headlight housing 7" round DOT compliant with T10 5 Watt parking bulb. This assembly allows you to install your own led, hid, xenon or halogen bulb. The assembly accepts P43T H4 headlight bulb. These DOT headlamp assemblies are designed for USA right hand traffic LHD. The headlight housing is made of plastic. The assembly is CE and Rohs listed. The headlight semi sealed housing assembly has a clear lens. This assembly works great for vintage and classic vehicles with older faded glass or plastic headlights. For 6 volt positive ground and 6 volt negative ground vehicles you can use our 6 volt led bulbs and upgrade you old vehicle to led lighting. Easy DIY just remove existing headlight assembly and install this semi sealed headlight assembly usually by 3 screws. This headlight works good for motorcycles, scooters and tractors that are old and either 6 or 12 positive and negative ground systems.

H11 male waterproof connector to H1 female waterproof connector. Made of heavy duty wire for high power uses such as headlights and driving lights. Harness about 9 1/2 Inches long. UL 1015 #18 awg cable. Handles up to 55 watt of power.

P13W/PSX26W LED Headlight 9 to 40 Volts No Polarity 12000 LM Pair. Works either positive ground or negative ground. Operates from 9 to 40 volts non polarity. Uses about 23 watts for the pair. The bulbs uses 1.91 amps at 12 volts. Available in White 6000K. Long life up to 30,000 hours. 2 year warranty. Includes two bulbs per package.

9006 male water proof to h11 female waterproof harness. CE and Rohs listed. Made of heavy duty wire for high current applications. Great to change your headlight or adapt a different headlight to your automobile. About 9.5 inches long. UL1015 #18 ,can handle up to 55w power.

40 watt, High, Low beam, CAN Bus, 3,600 lumen High Beam output and 2500 lumen Low Beam output. up to 50,000 hour life, LED circuit protection, made with heat sink, Built in EMC decoder/CAN bus, so no error codes. 360 degree viewing angle. IP 68 rated Waterproof, shock proof and dust proof. Made from Aluminum Alloy materials. CREE LED's. Built in fan helps to keep LED's cool and lengthen lifespan. NO UV. Packaged with 2 lead headlights per package. Up to 4000 Lumen output. Comparable to a 360 Watt incandescent light bulb. Longer life than halogen bulbs. White 6000-6500K.

Fits H4 female socket. Up to 20 Watts of power. 12 Volt DC. Comparable to a 180 Watt incandescent light bulb. M2S HID Xenon bulb style for perfect fit every time. Long life up to 30,000 hours. CE and Rohs listed. Available in White 6000-6500K. Since led lights are solid state you do not have to worry about broken glass filaments. Since only uses 20 Watts of power saves the life of the battery so you can leave your headlights on longer. Up to 1400 Lumen output. Comes 1 headlight bulb per package.

Fits H4 socket. Great for ATV, Motorcycles and scooters. Up to 1000 Lumen output. Operates from 12 to 36 Volts DC. Uses about 1 Amp. Very low power to make batteries last longer. CE and Rohs listed. LED output up to 12 Watts for the high beam. Long life up to 30,000 hours. Dual beam hi and lo beam. Comparable to a 75 watt incandescent bulb. Fits HID xenon M2S style bulbs. Long life never have to worry about a broken filament since led bulbs are solid state. Available in White 6000-6500K. Made of aluminum materials to keep the leds cooler so they have a longer life. Comes 1 headlight bulb per package. Long warranty please see warranty details on its product detail page. Made with aircraft aluminum radiator. Operating temperature from -40C to +105C.

Up to 1500 Lumens. Uses only 18 Watts. Comparable to a 180 Watt incandescent head lamp. Long life up to 30,000 hours. Long warranty please see detail page for more warranty information. CE and Rohs listed. Available in White 6000-6500 Kelvins. Solid state do not have to worry about a broken filament. Fits same size as L1 HID Xenon and quartz bulbs. Easy to remove old bulb and install led headlight. These led bulbs are package 1 per package.

9007 LED Headlight 9 to 40 Volts No Polarity 12000 LM Pair. Works either positive ground or negative ground. Up to 6000 Lumens for the high beam. Uses 1.91 Amps at 12 volts. The led headlight is not dimmable. Operates from 9 to 40 volts no polarity. Available in White 6000K. 2 year warranty.

H1 LED Headlight 9 to 40 Volts 8000 LM Pair. Works only negative ground. Wide voltage from 9 to 40 volts. Available in White 6000K. This bulb is not dimmable due to the wide voltage. Long life up to 30,000 hours. Comparable to a 55 to 65 Watt halogen bulb. Maximum voltage 45 volts. Includes two bulbs per package.

Up to 2000 Lumen output. Fits BA20D socket. The base is 20mm diameter. Both tabs are aproximately 0.575" from the bottom of the base. The width of each tab is 0.1185". Uses approximately 1.0 Amp@13.8 VDC for both low beam and high beam. Long life up to 30,000 hours. Made of aluminum to keep the led's cooler. Solid state illumiation so you do not have to worry about broken glass failures. Has a fan at the top to keep the led's cooler for a longer life. Available in White 6000K, Warm White 2700K and Warm White 3000K. Comparable to a 180 Watt incandescent light bulb. Uses only 20 Watts to increase the battery life. Very bright product both the low beam and high beam. CE and Rohs.

P15D-30 LED Headlight 12 Volt 30 SMD. Works either positive ground or negative ground. UP to 400 Lumens. The base is 15mm and the ring is 30mm. The smd are positioned where the filament would be for optimal light output. The lamp is dim-able using a varying voltage source. The max voltage is 14.2. Super long life up to 30,000 hours. Made with 5730 smd for maximum output. The base diameter is 15mm. The ring is 30mm. There are two contacts. Please make sure that you have a voltage regulator in your headlight circuit for your vintage bike or the led headlight will fail due to over voltage. One contact is for low beam. One contact for high beam. CE and Rohs. Other names DC prefocus, double contact prefocus or double contact candelabra prefocus. The M.O.L. is 1.962" and the diameter is 0.741". This is a NCNRNW Non-Cancelable Non-Returnable Non-Warranty, please see policies for more details.

H4 base. Operate 9-85 Volts. Output power 18 Watts for high beam. Up to 15 Watts for low beam. Uses only 1.5 Amps. Luminous output in Lumens 1500lm. Long warranty please see details on page. Long life up to 30,000 hours. The beam is 120 degrees. This headlamp has two filaments. Since the headlight is led it is solid state so you do not have to worry about broken glass or filament. Available in White 6500 Kelvin. Works in vintage and classic 12V positive or negative ground for cars, trucks, motorcycles, ATV's and tractors. This lamp is comparable to a 180 watt incandescence bulb. One headlight is sold per package. This head light is comparable to a projector beam motorcycle and scooter headlight. Easy DIY to remove the old headlight and install led headlamp. Very long life and very bright. Made with red copper aluminum alloy. Compatible with the following: H4 H8 H11 9005 9006 Fits HID Xenon L1

5202/PSX24W LED Headlight 9 to 40 Volts No Polarity 12000 LM Pair. Operates either positive ground or negative ground. Works from 9 to 40 volts non polarity. Uses up to 23 watts per pair. The consumption is approximately 1.91 amps at 12 volts. Available in White 6000K. Long life up to 30,000 hours. 6,000 Lumens per bulb. Two year warranty. Load equalizers maybe required. Includes 2 bulbs per package.

H4 P43t base 6 Volt LED headlight for vintage vehicles and classic motorcycles. This led is designed for 6 volt motorcycle headlights. Works either AC or DC voltage. Very bright. Dual high and low beam. Up to 750 Lumen output. Comparable to a 50 - 75 Watt incandescent bulb. Made with the latest smd leds 5730. The profile of the led fits inside of a normal light bulb so you know it will fit your application. Operates either 6v positive ground or 6v negative ground. Up to 650 Lumens for high beam and up to 510 Lumens for low beam. This headlight bulb is up to 50 candle power CP for high beam. Up to 40 candle power CP for low beam. Long life up to 30,000 hours. This bulb uses approximately .490 amp @ 6.9 volts for hi beam. The bulb comes in White 6000K and Warm white 3000K. The Warm White simulates the original color of a incandescent light bulb.

p45t led headlight. Operates 6 volt positive ground or 6 volt negative ground. Up to 900 Lumen output or 70 CP for high beam. Up to 600 Lumen output for low beam. Available in warm white 3000k and white 6000k. Long life up to 30,000 hours. Since led's are solid state you do not have to worry about a broken filament or glass. CE and Rohs listed. Dual beam low and high beam. Works great for old vehicles made before World War II such as Ford Model A's and T. Easy DIY replacement just remove old incandescent and replace with new led bulb. Since led's use up to 90% less energy they really help the old generators and alternators with such a reduced load. Comparable to a 55 to 65 Watt incandescent bulb. The maximum diameter is 1.058" inches. The maximum overall length is 1.944 inches. Fits standard connector such as part number 34265. The pin out looking from the back is: Left side contact is ground.

H4 LED Headlight 9 to 40 Volts No Polarity direct fit. Works either positive ground or negative ground. The low or high beam Lumens are up to 6000 Lumens for each led headlight bulb. Uses 1.798 Amps for the high beam. Uses 1.762 Amps for low beam. High beam Lumens up to 6000 per led headlight bulb. Up to 22 Watts for low beam or the high beam. Comparable to a 50 to 55 Watt incandescent bulb. This bulb is not dimmable due to the wide voltage. Available in 6000K. The light source is small 4.5mm x 1.4mm about the same size as a incandescent bulb. Since the light source is small and similar to a incandescent bulb you have better light pattern projected on the street. Has anti dazzle low beam cup to keep the oncoming drivers from being blinded. Has built in fan to keep the led's cool so they last longer. Up to 1 Year warranty. P43t Headlight bulb fits a standard H4 female socket.

Headlight Semi Sealed Housing 5 3/4" Inch Round With Park Bulb Pair. Accepts P43t H4 bulb. Comes as a pair two semi sealed fixtures. The fixture is DOT certified. Has parking light T10 harness for T10 wedge. H4 bulb not included. Great for vintage classic cars, trucks, motorcycles to upgrade that old bulb to a new led bulb with a semi sealed fixture. Compatible with sealed beams H5001, 5001, 4001, 4004, H5010, H5501, H4001, GE 4013. CE and Rohs.

H3 LED Headlight 6 to 9 Volt DC negative ground. Works great for classic and vintage vehicles. The headlight is packaged with 2 headlights. Up to 1,400 Lumens. Single filament. Available colors is White is 6000K and Warm White 3000K. Life up to 30,000 hours. Up to 16 LED Watts output. Comes two headlights per package. This bulb is not dimmable because of the wide voltage 6 to 9 volts. Works great in 8 volt Fords.

P15D-30 LED Headlight bulb. Works both positive chassis and negative chassis. Operates voltage from 5 to 30 Volts full brightness at any voltage in that range. This bulb is a dual filament bulb both low beam and high beam. Up to 1200 Lumens low beam and 1800 Lumens high beam. The base is a P15D-30 base with two contacts. One contact is low beam and the other contact is high beam. The diameter is 15mm for the base and 30mm for the ring with 3 holes. Available in White 5000-6000K and Warm White 2700-3300K. Dimensions are overall length is 2.52 inches. The width is 0.98 inches. The length of the body above the BA15D base is 1.77 inches. The circuit board is super conducting aluminum for maximum power supplied the the led's. The led headlamp is a constant current device so the brightness will not fluctuate. CE and Rohs listed.

P36D base 5 to 30 volt positive ground or negative ground. Made with 16 2525 leds. Made with aluminum to keep the leds cooler so they last longer. This bulb is non polarized. Up to 1800 Lumen output for high beam up to 1200 Lumen output for low beam. Uses only 1.4 Amps high beam and .8 Amps for low beam. Long life up to 30,000 hours. Easy to replace just remove old bulb and insert new led bulb. CE and Rohs listed. Comparable to a 55W to 65W halogen bulb. This retrofit take around 1 minute to change the the old bulb. Dimensions are overall length is 2.52 inches. The width is 0.98 inches. Load equalizers may be required, if the bulb will not switch from low beam to high beam or if the bulb flickers when installed. Please install led light load equalizers to fix the problem product code 65832. Available in 6000K to 6500K. Compatible with: 312 30/24W 6 VOLT PRE-FOCUS Lucas 446, 414, 370, AND 312

12 Volt non polarity, up to 950 Lumen output for high beam. Up to 700 Lumen output for low beam. Dual filament. The bayonets are parallel. Works either 12 Volt positive ground or 12 Volt negative ground. 60 5730 SMD's very bright. Long life up to 30,000 hours. The leds are optically aligned with the reflector for maximum led light output. This led headlamp as 20 forward firing and 40 side firing led's. This bulb is non polarity sensitive so you can use it in both positive or negative ground vehicles, motorcycles and trucks. The bulb is dim-able using a variable voltage source such as your dashboard dimmer switch. Comparable to a 35 to 55 Watt incandescent. Available in White 6000 K, Warm White 3000 K. UP to 70 CP for the high beam. The maximum overall length M.O.L is 1.944". The maximum diameter is 1.05". Up to 300 Lumen for forward firing for the high beam.

LED headlamp 12 volt BA15S base. Single filament. Up to 950 Lumen output. BA15S base two bayonets same height and 1 contact in a 15mm base. This bulb works either 12 Volt positive ground or 12 Volt negative ground. CE and Rohs listed. Comparable to a 37 to 57 Watt halogen bulb. 360 degree viewing angle. The leds are aligned with your reflector for maximum led light output. Available in white 6000k and warm white 3000k. Dim-able with a variable voltage supply. Smaller than a normal light bulb so its easy to install. Long life up to 30,000 hours. This is a single element bulb so its on and off. The M.O.L. Maximum overall length is 1.944 inches. The diameter is 1.058" Compatible with: Ryobi and Husqvarna Lawn Tractors and Mowers Husqvarna 532004152

BA15S LED Headlight. This lamp has no polarity, non polarized or bi polar. The led headlight is designed for both positive ground or negative ground. BA15S base single contact. Super bright up to 1,200 Lumen. Headlight has aviation aluminum to keep the leds cool so they last longer. Wide voltage 5 to 30 volts AC or DC. The LED's are csp high power. The circuit board is super conducting aluminum. The headlight uses wide voltage and a constant current design. The leds are on both sides so the led light will project light into the housing. The base diameter is 15mm and has a single contact. The bayonets are the same height. Available in White 6000K to 6500k. Long life up to 30,000 hours. Comparable to a 45 to 55 Watt incandescent bulb. The current consumption is 800mA. The socket is made of copper for maximum conductivity. Dimensions are overall length is 2.52 inches.

Par 56 7" diameter. 12 Volt negative ground sealed beam, operates from 10-80 VDC. This headlight has both a low and high beam. The low beam Lumen output is up to 1500. The high Lumen output up to 3000. The rated power is Rated Power: hi/lo 30W/15W. Comparable to a 140 Watt incandescent light bulb. Made with CSP chips so it is very bright an d focused. Available in white 6000k and warm white 3000k. .250 push terminals to connect the wires using H4 socket. The lens is clear. Long life up to 30,000 hours. Available in White 6000K and Warm White 3000K. The lens is PC and the frame is diacase Alu. IP 67 rated. Load equalizers required if the light flickers on low beam or you cannot change from low beam to high beam. The 6 Ohm 50 Watt LED Headlight Load Equalizer is product code 54738. The fixture overall thickness is approximately 3.90". The diameter is approximately 7.00".

LED headlamp works either positive ground or negative ground. Wide voltage from 5 to 30 Volts AC or DC. Available White 6000K to 6500K or Warm White 2700K to 3300K. No polarity, Bi polarity, non polarized. Made with 16 2525 smd for super bright. The headlamp lights on both sides. Dual filament both a low and high beam. The low beam Lumen output is up to 1200 Lumens. The high beam is up to 1800 Lumens. Great for vintage and classic cars. Long life up to 30,000 hours. CE and Rohs certified. Made with aluminum to keep the led lamps cool so they can operate for a long life. The circuit board is constant current so the leds should not flicker. Available in White 6500k. Perfectly works with product 69854 is a 7" round semi-sealed housing and 68721 is a 5"x7" rectangle housing. Both these semi-sealed housings use the P43T bulb.

For positive ground or negative ground. 5 to 30 Volt wide voltage. Long life up to 30,000 hours. Made with 2525 LED's for long life. Dual filament up to 1200 Lumen low beam. Works both in a socket that is wired for a single filament and works in a ba15d socket that is wired for dual filament. Up to 1800 Lumen high beam. The base is BA15D the diameter is 15mm with two contacts on the bottom and parallel bayonets. Made with aviation aircraft aluminium to keep the leds cool for longer life. Available in White 5000-6000K and Warm White 3000K. Dimensions are overall length is 2.52 inches. The width is 0.98 inches. The length of the body above the BA15D base is 1.77 inches. The circuit board is super conducting aluminum for maximum power supplied the the leds. The led headlamp is a constant current device so the brightness will not fluctuate. CE and Rohs listed.

P36D 5 to 30 Volt positive ground or negative ground non polarized. Made with 2525 led's for long life up to 30,000 hours. High Lumens up to 1200 Lumens. Uses only .8 Amps. Works great for 6 volt vintage cars, motorcycles and tractors. The heat sink is made of aluminum to make the leds operate cooler so they are brighter and last longer. CE and Rohs listed. Comparable to a 45 to 55 Watt incandescent light bulb. Takes just minutes to install. Just remove the old bulb and insert the new led bulb. The base is P36D has one contact on the bottom and diameter of flange is 36mm. Dimensions are overall length is 2.52 inches. The width is 0.98 inches. Load equalizers may be required, if the bulb will not switch from low beam to high beam or if the bulb flickers when installed. Please install led light load equalizers to fix the problem product code 65832. Available in White 6000K to 6500K.

P15D-25-3 LED Headlight 5 to 30 Volts Non Polarity. Has 3 claws or bumps on the disc. Operates either positive ground or negative ground. Works wide voltage range from 5 to 30 Volts full brightness. Comparable to a 35 to 55 Watt incandescent bulb. Dual beam, high beam up to 1800 Lumen output and the low beam up to 1200 Lumen output. Up to 30,000 hour life. Made with aviation aircraft aluminum to keep the led's cool for longer life. Available in White 5000-6000K and Warm White 2500-3500K. Dimensions are overall length is 2.52 inches. The width is 0.98 inches. Made with led's on both sides. 8 high power leds on each side. One row of led's on each side illuminate for low beam. Both rows of led's on each side illuminate for high beam. Uses up to 800mA for low beam and up to 1.4A for high beam.

LED Headlight BA15D base. Two filaments high and low beam. BA15D base has two parallel bayonets with two even contacts. The led headlamp life up to 30,000 hours. The led's are aligned for best led lighting using the reflector. The bulb is dim-able using a variable voltage supply. The led bulb can be used as a headlight or as a taillight brake light. CE and Rohs listed. The bulb outline is smaller than the original bulb so you should not have any fit issues. Comparable to a 27 to 35 Watt incandescent light bulb. Available in white 6000K and warm white 3000K. Please see bottom of the page for warranty details. This bulb has no polarity so it can work in both positive ground and negative ground chassis vehicles, motorcycles and tractors. Up to 600 Lumen output. Two brightness levels, dual filament. Up to 50 CP. This LED uses up to .130 Amps @ 13.8 Volts for low beam and .500 Amps @ 13.8 Volts high beam.

P15D-30 LED Headlight 8 Volt 60 SMD. Works either positive or negative ground. Great for classic and vintage vehicles such as Fords. Please make sure that you have a voltage regulator in your headlight circuit for your vintage bike or the led headlight will fail due to over voltage. CE and Rohs. This is a NCNRNW Non-Cancelable Non-Returnable Non-Warranty, please see policies for more details. The product is tested before shipping. Compatible with: Please make sure contacts are aligned the same for 2320, sometimes they are rotated. Acceptable voltage range 6.53 to 9.47. Please see our wide voltage full bright product code 62528. Has both high beam up to 900 Lumen and low beam up to 600 Lumen output. Dimmable with a variable voltage supply. Up to max voltage of 10 Volts. Maximum overall length is 1.95" and maximum overall diameter is 1.0". Dimmable with a variable voltage supply.

P15S-30 Solder-able Cap. Has one contact on the bottom for single filament bulbs. Apporoximate size 0.732" MOL by 0.591" for the base diameter, the ring is 1.175" diameter. The ring has 3 holes, plus a tiny notch.

Headlight led 12V P15D-25-1 dual filament. Dim-able with variable voltage. Up to 650 Lumens. Long life up to 30,000 hours. The led bulb is smaller than your original bulb so you should not have any installation issues. Available in white 6000k and warm white 3000k. The lamp uses 5730 smd led for high power lighting. Each led is aligned to your fixture so the most light will reflect. Extended warranty please see bottom of page for warranty details. The M.O.L. is 1.962" and the diameter is 0.741". Compatible with: p15d-25-1 PX15d H6 h6m P15D

P15D-30 LED Headlight 12 Volt. Up to 900 Lumens. 360-degree viewing angle. Dim-able using a variable voltage supply. CE and Rohs listed. Long life up to 30,000 hours. Comparable to a 45 to 55 Watt incandescent light bulb. The SMD are aligned so they match your reflector for maximum light output. Available in white 6000k and warm white 3000k. Trade names are DC pre-focus, double contact pre-focus or double contact candelabra pre-focus. Please make sure your headlight circuit has a voltage regulator for the vintage bikes or the led headlight will fail due to over voltage. Maximum overall length is 1.944 inches. The maximum diameter is 1.058". This is a NCNRNW Non-Cancelable Non-Returnable Non-Warranty, please see policies for more details. The product is tested before shipping. Dual filament high beam up to 900 Lumens and low beam up to 600 Lumens. Works both positive ground or negative ground. M.O.L.

P15D-25-1 base. Dual filament, up to 950 Lumens per each filament. 12 Volt non polarity works either positive ground or negative ground. Uses 60 5730 smd leds. Up to 57 to 67 Watt incandescent equivalent. The leds are aligned with your reflector for maximum light output. Dim-able with a variable DC supply such as a dimmer switch. Available in white 6000K and warm white 3000k. Extended warranty, please see detail page for more information. Maximum overall length is 1.944 inches. The maximum diameter is 1.058" Compatible with: p15d-25-1 PX15d H6 h6m P15D

P15D-30 LED Headlight 8 Volt 30 SMD for 8 volt Fords. Great for vintage and classic cars and trucks. For positive ground or negative ground. Please make sure that you have a voltage regulator in your headlight circuit for your vintage motorcycle or the led headlight will fail due to over voltage. CE and Rohs. This is a NCNRNW Non-Cancelable Non-Returnable Non-Warranty, please see policies for more details. The product is tested before shipping. P15D-30 LED Headlight 8 Volt 60 SMD. Works either positive or negative ground. Great for classic and vintage vehicles such as Fords. Please make sure that you have a voltage regulator in your headlight circuit for your vintage bike or the led headlight will fail due to over voltage. CE and Rohs. This is a NCNRNW Non-Cancelable Non-Returnable Non-Warranty, please see policies for more details. The product is tested before shipping.

P15D-25-1 LED Headlight 5 to 30 Volts Non Polarity has one claw or bump on the disc. Works either positive ground or negative ground. Since operates wide voltage range of 5 to 30 Volts the led bulb is full brightness within that voltage range. Comparable 35 to 45 Watt halogen bulb. Up to 30,000 hour life. Dual beam, low beam up to 1200 Lumen output. High beam up to 1800 Lumen output. Made with aviation aircraft aluminum to keep the led's cool for longer life. Available in White 5000-6000K and Warm White 2500-3500K. Dimensions are overall length is 2.52 inches. The width is 0.98 inches. Made with led's on both sides. One row of led's on each side illuminate for low beam. Both rows of led's on each side illuminate for high beam. Uses 800mA for low beam and 1.4A for high beam. Since this bulb is led it uses 90% less power than your halogen or incandescent bulb which is easier on your generator or alternator.

5 to 30V positive ground or negative ground non polarity. P45t base, has a notch on the side not shown. Made with 16 Cree 2525 LEDs. Available in 6000K to 6500K. Dual filament the low beam Lumens up to 1200. The high beam Lumens up to 1800. Long life 30,000 hours. Made with aluminum for long life. Uses only 800mA. Uses around 9.6 Watts. Constant current the driver to reduce flicker. The base is P45t. This led bulb is for old vintage and classic cars, trucks, motorcycles, and scooters. Long-life up to 30,000 hours. 8 LEDs on each side for best illumination. When looking at the connect from the rear the ground is the left-most contact. The center contact is the low beam. The rightmost contact is the high beam. Please click on the manual to see the wiring diagram for this bulb. 4 smd chips will be lit for low beam both sides and all 8 smd chips both sides will be lit for high beam.

P15D-25-3 LED Headlight 6 Volt. 6V positive ground and 6V negative ground. For classic and vintage vehicles that use the P15D-25-3 pre focus base. Long life up to 30,000 hours. Comparable to a 27 Watt to 35 Watt incandescent light bulb. 360 degree viewing. Available in white 6000K and warm white 3000K. Up to 600 Lumen output. Uses quantity 30 5730 leds, which each 5730 output uses up to a 1/2 Watt. The LEDs are positioned for the best optically aligned LED to reflector. Due to this alignment you get the best led output. This bulb is dim-able using a variable voltage supply. The approximate size M.O.L. is 1.962" and the approximate diameter is 0.741". Up to 510 Lumens low beam. Up to 650 Lumens high beam. This headlight bulb uses approximately 0.112 Amp @ 6.9 volts for low beam. This led headlamp bulb uses around 0.490 amp @ 6.9 volts for hi beam. Life up to 30,000 hours.

BA20D LED headlight 5 to 30 volt, dual filament, no polarity. High beam up to 1800 Lumen. Low beam up to 1200 Lumen. The high beam is up to 1800 Lumens. Incredibly bright. Operates 5 to 30 Volts which means it will work at 6 volts or 30 volts. If you generator puts out higher voltage than 6 volts this light will work up to 30 volts. The bulb will work either AC or DC, meaning non polarized. Works either positive ground or negative ground. There are two contacts on the bottom one for low beam and one for high beam. This bulb is the perfect upgrade for scooters. Available in 6000K to 6500K. Load equalizers may be required, if the bulb will not switch from low beam to high beam or if the bulb flickers when installed. Please install led light load equalizers to fix the problem product code 65832. This product the BA20D base the bayonet is the same facing as the led's.

6V LED Headlight. Works 6V AC or 6V DC. 60 quantity 5730 smd leds. Optically filament aligned so you get maximum light output through your headlight fixture and lens. The headlight is dimmable using a variable voltage supply. Being dimmable helps out with the older vintage and classic vehicles voltage system and wiring is not 100%. There is a total of 16 forward firing and 44 side firing leds. Each 5730 uses up to 1/2 Watt of power. This bulb up to 950 Lumen or 70 MSCP for high beam. Low beam up to 500 Lumens or 40 CP for low beam. Compatible with C-6 filament designed light bulbs. Comparable to a 30 Watt to 55-56W Watt incandescent light bulb. This bulb works in both 6 volt negative ground and 6 volt positive ground vehicles, tractors and motorcycles. This lamp can operate 6 Volts and has both a low beam and a high beam filament. Long life up to 30,000 hours.

Par 36 led headlight. Operates positive ground or negative ground 10-80 Volts AC/DC. This bulb is a single trapezoidal light beam single filament. Up to 1800 Lumen output. 24V@0.48A, 12V@0.97A. Comparable to a 160 Watt incandescent bulb. Available in white 6000k and warm white 3000k. Long life up to 30,000 hours. The housing is sealed. Screw terminals are used to connect the wires. Made with quantity 6 2525 CREE 3 Watt led's for long life. Uses about 18 Watts. Approximate 4.5" diameter and about 2.04" in thickness not including the depth of the connectors. Keeper tab to stop the bulb from rotating. Rectangular spot beam. The base is made of Diecast-Aluminum. The lens is made of poly carbonate material. IP 67. This par36 bulb is not dimmable in the wide voltage 11-80V AC/DC. The bulb shows some dimmability from 7.5 V to 11.00 V. The screw is terminal GX53. CE and Rohs listed. Compatible with: Wagner 4449

P15D-25-3 LED Headlight. Operates 12 Volt positive ground or negative ground. Dim-able with a variable voltage source. Long life up to 30,000 hours. Up to 650 Lumen output. Dual filament low and high beam. Comparable to a 27-37 Watt halogen. The led lamp is smaller than the outline of the bulb you are replacing so you should not have any installation issues. The leds are optically aligned to your reflector so you get maximum light output. Available in ultra white 6000k and warm white 3000k. Euro-style white light. Uses about 3.75 Watts@13.8 volts. The M.O.L. is 1.962" and the diameter is 0.741". Compatible with: BMW M5 Headlight style 34901-GCH-004

Eliminates, decodes emc headlight error codes. This decoder/capacitor operates at 12 Volts DC. The maximum current is 4 Amps. Fits the led headlamps below. Compatible with: H1 H3 H7 H8 H9 H11 H16 9005 9006 5202

BA20D LED headlight 5 to 30 volt. The base is rotated 90 degrees. High beam up to 1800 Lumen. Low beam up to 1200 Lumen. The high beam is up to 1800 Lumens. Incredibly bright. Operates 5 to 30 Volts which means it will work at 6 volts or 30 volts. If you generator puts out higher voltage than 6 volts this light will work up to 30 volts. The bulb will work either AC or DC, meaning non polarized. Works either positive ground or negative ground. There are two contacts on the bottom one for low beam and one for high beam. This bulb is the perfect upgrade for vehicles, motorcycles and scooters. Available in 6000K to 6500K and Warm White 2700K to 3300K. Load equalizers may be required, if the bulb will not switch from low beam to high beam or if the bulb flickers when installed. Please install led light load equalizers to fix the problem product code 65832.

HID Hi beam is not showing the indicator icon. This will fix that issue when you replace HID headlamps with LED. Also called a HID high beam negative eliminator. The product is made from ABS plastic and has the electronics potted for a long life. CE and Rohs listed.

This headlight semi sealed housing is DOT approved. The lens color is clear. The head light housing accepts H4 P43T base headlights. You can use halogen, xenon, hid or led head bulbs as long as they are P43T base. Since these assemblies are DOT approved they are designed for driving in United States on the right hand side of the road RHD. The dimensions are 5" by 7" 200mm. The head light assemblies are easy to install usually remove 3 to 4 screws remove old glass or plastic headlight housing and insert new headlight housing and your new bulbs. These headlight housings work great for vintage and classic vehicles such as 6 volt or 12 volt positive or negative ground. Please check the warranty at the bottom of the page. The housing comes with a T10 5 Watt parking bulb that you can use for your parking light if needed. You can also upgrade this bulb from incandescent to led for the reliability of led lighting.

Eliminates headlight emc error codes for dual beam headlights. This is both a headlight decoder and a headlight capacitor to provide error free emc codes. Operates 12 Volt DC. Up to 4 Amps max. This is a electronic decoder. Compatible with: H4 H13 9004 9007

LED Headlight 6V BA15S male base single contact bayonets parallel. Up to 900 Lumen output. There are 16 forward firing 5730 smd led and 44 side firing smd leds. The leds are optically aligned filaments for optimum light output using your lens and light fixture. The bulb is dimmable so with your older vintage and classic cars you do not have to worry that you lights will flicker when you get low voltage, the headlight will slowly dim as your car battery or generator is putting out less voltage. This led lamp outputs up to 900 Lumens, or 60 MSCP to 70 CP candle power. The base is ba15s with bayonets parallel to each other and one contact on the bottom. You can use this bulb in 6 volt positive ground or 6 volt negative ground classic and vintage cars. Available in White 6000K and Warm White 3000K. Up to 340 forward firing Lumens and 560 side firing Lumens.

Use this HID to eliminate HID error codes. Operates 12 Volts DC. Up to 4 Amps. When you replace HID with LED you have to add this to eliminate errors. Compatible with: C6 AL

P15D-30 LED Headlight 6 Volt. This lamp outputs up to 900 Lumen output or up to a 60 to 70 CP Candle power. This bulb is comparable to a 45 to 55 Watt incandescent light bulb. There are two filaments low beam and high beam. The outline of this bulb is smaller than the original light bulb so you know it will fit and work. The led light has optically aligned to the filament focal position of the original light bulb. Aligning the SMD to the filament focal point ensures you get maximum light output to your light fixture and lens. The base is 15mm diameter and the ring is 30mm diameter. The bulb is dim-able so you do not have to worry that the light bulb will shut off when you have a low voltage issue in your classic or vintage car, truck, tractor or motorcycle, and the voltage drops below 6 volts. This bulb will work in both a positive ground chassis and negative ground chassis 6 volt systems.

P15D-30 LED Headlight 6 Volt. This led has 30 5730 smd leds. The Lumen output is up to 800 or up to 63 CP. This bulb has been designed to be exactly like a filament bulb but using leds. The leds are is the same position as the original filament. The life is up to 30,000 hours. Please see warranty details on the same page. This bulb is available in white 6000K and warm white 3000K. The light is dim-able which works good for older vintage and classic automobiles, motorcycles and tractors. The base has 15mm base. There are two contacts on the bottom one is used for high beam and the other is used for low beam. There are 3 claws the are spaced 120 degrees for maximum support. Sometimes called DC prefocus, double contact prefocus or double contact candelabra prefocus. Please be careful when inserting or removing the bulb that the locking flange does not bind or break.

Headlight bulb 6 Volt Positive Ground or Negative Ground. BA15S base. Up to 700 Lumen, 55 CP. Single filament design. Designed for reflector headlights since most of the leds are side firing directly into the reflector. The bulb has some forward firing leds to make it brighter. This LED bulb is designed for early vintage Ford Model T and Ford Model A. Long life up to 30,000 hours. The M.O.L. is 1.962" and the diameter is .741". Plug and play remove the old incandescent bulb and replace with LED bulb. The LED uses less power than a incandescent bulb so it is easier on the wiring of the older vehicles. The bulb comes in White 6000K and Warm white 3000 K. The Warm White simulates the original color of a incandescent light bulb. How ever the Warm White is about 5% less output than the 6000 K bulb. CE and Rohs certified.

P15D-25-1 LED Headlight 6 Volt. Up to 900 Lumen or 60 to 70 CP candle power for high beam. Up to 400 Lumens for low beam or 30-40 CP. Available in white 6000K and warm white 3000K. The bulb is dimmable so you do not have to worry about the headlight fail when voltage drops below 6v. This bulb is optically aligned so you will get the maximum light output at your lens. Long-life up to 30,000 hours. Please see warranty for extended warranty details. This led lamp shape fits inside the outline of the existing light bulb so will be an easy installation. The bulb has 60 5730 SMD. There are 16 forward firing and 44 side firing leds. Illuminate directly in front of you with forward-firing chips and the side-firing will reflect light into the reflectors. Since these led bulbs are not polarity sensitive they operate in both positive ground and negative ground systems. This bulb can operate AC or DC.

9005/H10/9012 LED Headlight 9 to 40 Volts No Polarity. Works either positive ground or negative ground. Works from 9 to 40 volts. Up to 6,000 Lumen per bulb. Uses about 23 LED Watts per pair. Uses 1.91 amps at 12 volts. Single filament. Long life up to 30,000 hours. Available in White 6,000K. Maximum 45 volts. Load equalization maybe required. 2 bulbs per package. Please see warranty for details. CE, Rohs, DOT.

Use one load equalizer for each led bulb in your turn signal circuit. Since this heavy duty load equalizer runs cooler it last longer. Stops hyper flashing and fixes CAN bus errors. Operates 6 Volt or 12 Volt positive ground or negative ground. The wire is 14 AWG high temperature. Comes with two insulation displacement connectors "IDC". Please do not cut your vehicle or motorcycle wires, just crimp the IDC on to your existing wires so that the load equalizers are in parallel with the led bulbs. The resistor body material is made from anodize aluminum. The rated current is up to 4 Amps. Since the load equalizer is 50 Watt power dissipation it runs cooler. The led light equalizer will get hot to the touch so it is recommended to mount to a metal surface. The body has mounting holes so you can easily attach it to a metal surface. The operating temp is around 100 degrees Celsius.

Use only two 3 Ohm 50 Watt Load Equalizers for your vehicle for the left and right side. Stops led light hyper-flashing and fixes CAN bus errors. Operates 6 Volt or 12 Volt positive ground or negative ground. The load equalizer can handle up to 4 Amps either 6 Volt or 12 Volt positive ground or negative ground. Since the resistor body is larger it runs cooler so load equalizer will last longer. The wire is 18 AWG high temperature resistant wires. Comes with two insulation displacement connectors so you can crimp these on to your existing wiring. Please install in parallel and do you cut your vehicle wires. Since the 3 Ohm 50 Watt is designed to install on the left or right side you only use two load equalizers instead of four. The load equalizer body is made of anodized aluminum. Please make sure to mount to metal surface since the body of the load equalizer gets hot.

Fixes flashing headlights or headlights that will not change from low beam to high beam. Operates 6 Volt or 12 Volt positive ground or negative ground. This heavy duty led headlight load equalizer operates cooler so it last longer. Rated at 4 Amps. Body is anodized aluminum. Comes with two insulation displacement connectors "IDC". Please crimp on to your existing wiring in parallel with the low beam on both your headlights. No need to cut your wiring harnesses when using the insulation displacement crimps. To test once installed the load equalizer should get warm or hot to the touch when you headlights on are low beam. The load equalizers come with 14 AWG heat resistant wiring. Please mount to a metal surface to help the load equalizer stay cooler. No need to purchase expensive and complicated harnesses when using these load equalizers. The wire length is about 4.5".

Used with a LED Light to simulate that the original light bulb is installed. Easy to install. Keep away from plastic or painted surfaces, resistor gets very hot. Connect the load equalizer in parallel with the led light you are replacing. Includes 7" of 20 awg stranded Teflon wire. 2 wire crimps included. Use one 6 Ohm 25 Watt equalizer for each LED bulb, or use one 3 ohm for 2 led bulbs for each turn signal control side that you replace. For a 6 Ohm load equalizer you can attach up to 1 LED light per equalizer. For the 3 Ohm load equalizer you can attach up to 2 LED lights per equalizer. Load equalizer dimensions are 0.75 inches in length and 0.42 inches wide. No special tools needed just a pair of pliers. The connection is made using insulation displacement connectors. This load equalizer eliminator capacitor operates from 6 to 12 volt positive ground or negative ground.

Used with a LED Light to simulate that the original light bulb is installed. Easy to install. Keep away from plastic or painted surfaces, resistor gets very hot. Connect the load equalizer in parallel with the led lamp you are installing. Approximate 6" of 20 AWG stranded Teflon wire. 2 wire crimps included. Use one 6 Ohm equalizer for each LED bulb, or use one 3 ohm for 2 led bulbs for each turn signal control side that you replace. Use one 20 Ohm or 100 Ohm for each side marker. For a 6 Ohm load equalizer you can attach up to 1 LED light per equalizer. For the 3 Ohm load equalizer you can attach up to 2 LED lights per equalizer. Load equalizer dimensions are 0.75 inches in length and 0.42 inches wide. (3 ohm equalizer is slightly larger). No special tools needed just a pair of pliers. The connection is made using insulation displacement connectors.

LED Headlight Load Equalizer works from 6 Volt to 12 Volt classic and vintage cars and motorcycles. Works either positive ground or negative ground. Please use a load equalizers for your low beam, one per side if your headlights are not working properly after installation. Sometimes after upgrading the older car electrical system does not recognize the new technology. Since led headlights use 80% less power, sometimes load equalizers are needed. Please connect the load equalizer in parallel with the low beam circuit. To connect parallel means one end of goes to the chassis and the other end connects to your low beam. Please use one per the left headlight and right side headlight. Included are insulation displacement crimps IDC. The IDC are easy to install using pliers and easy to remove. Recommended to install to the metal of the car to help dissipate the heat.

Fixes hyper flashing also eliminates CAN bus errors for double filament bulbs 7443. The inline load equalizer is made that you can unplug your bulb and plug into the harness. Then the other end of your harness plug into where your bulb used to plug in. No need for crimps. The harness is made of both 14 AWG wire and 18 AWG wire. The insulation near the load equalizer is heat resistant. Operates from 6 volt to 12 volt positive ground or negative ground vehicles or motorcycles. The load equalizer is 50 Watt and made of heavy duty aluminum so it last longer. Can handle up to 4 amps per filament, so 8 amps total for this inline load equalizer. Just unplug your led bulb and plug into the inline harness and plug the other end of the harness into your existing harness. The length of the harness is approximately 10". The metal body will get warm to hot so please mount to metal surface.

3157 inline load equalizer for dual filament 3157 led bulbs. Two load equalizers for both the taillight and blinker/brake light. Handles up to 8 Amps or 4 Amps per filament. The harness length is about 10". The wire harness is made of 14awg and 18awg. The insulation near the load equalizer is heat resistant. Plug and play just insert led bulb into inline load equalizer and insert inline load equalizer into your original bulb socket. This 3157 socket has two tabs. Works from 6 Volt to 12 Volt positive ground or negative ground vehicles or motorcycles. Easy to install no crimping or soldering needed. Since the load equalizers are 50 Watt they run cooler so they will last longer. Load equalizers are made of anodize aluminum for long life. Operates approximately 100C, please make sure to mount the equalizers to metal so they operate cooler. The load equalizers can become hot to the touch.

Fixes CAN bus errors and eliminates hyper flashing and fix CAN bus errors for dual filament 3157 led bulbs. Works from 6 Volt to 12 Volt positive ground or negative ground. Can handle up to 4 Amps per filament so a total of 8 Amps. Includes two 50 Watt load equalizers for long life and cooler operation. This is the 3157B type socket that has 3 tabs. Load equalizers get warm or hot to the touch so please mount the equalizers to a metal body to help reduce heat. The harness is about 10" long. The harness is made of both 14awg and 18awg wires. The harness insulation nearest the load equalizer is made of heat resistant materials. The load equalizer is made of aluminum materials. Both filaments are equalized to eliminate fast flashing or ODBC errors. Plug and play installation just remove the led bub and insert into the inline load equalizer then insert the inline load equalizer into the led bulb socket.

6 Ohm 50 Watt 7440 Inline Load equalizer. Heavy duty load equalizer runs cooler it last longer. Stops hyper flashing and fixes CAN bus errors for 7440 single filament. Operates from 6 Volt to 12 Volt positive ground or negative ground. The inline harness is made of 14 AWG wire. Please do not cut your vehicle or motorcycle wires, just insert "plug" into your existing wires. The resistor body material is made from anodize aluminum. The rated current is up to 4 Amps. Since the load equalizer is 50 Watt power dissipation it runs cooler. The led light equalizer will get hot to the touch so it is recommended to mount to a metal surface. The body has mounting holes so you can easily attach it to a metal surface. The operating temp is around 100 degrees Celsius. Installation instructions included.

Inline load equalizer. 3156 male and female sockets. For 6 & 12 VDC systems. Gets rid of the fast flashing, or hyper flash. Easy to install. CE and Rohs listed.

7440 Load Equalizer Warning Canceller. Use this to eliminate OBC errors, hyper flash or flickering errors by your automotive electronics. Please use one load equalizer for each led bulb.

For single filament 3156 led bulbs to eliminate hyper flashing and fix CAN bus errors. Operates from 6 Volt to 12 Volt positive ground or negative ground. Great for automobiles and motorcycles. Comes with one inline load equalizer for easy installation. Just remove the led bulb install the inline load equalizer then install the led bulb into the load equalizer. No crimping or soldering required. The load equalizers and get warm or extremely hot so please mount the equalizers to a metal surface. Since 3156 has only one filament, there is one load equalizer. The load equalizer can handle up to 4 Amps. Since the equalizer is one 50 watt so the load equalizer will run cooler. The harness is about 10" long, made of both 14awg and 18awg wire. The harness nearest the load equalizer is insulated with heat resistant materials. The operating temperature is approximately 100 degrees Celsius.

BAU15S load equalizer, inline sockets, eliminates, cancels hyper flash obd error message, dashboard error messages. CE and Rohs listed. 6 Ohm per inline harness. The wire on each side is 6" long, so between both side it is about 12" long. The ballast is epoxied so it is more weather resistant. BAU15S the bayonets more in a V shaped and not at the opposite sides of the socket. Since it is 6 ohms you have to use one load equalizer per led bulb in your turn signal circuit. Comes with both a male BA15S socket and a female BAU15S socket so it can be used inline. Since this is a inline BAU15S inline load equalizer you do not need to cut, pierce or crimp the existing wires.

Load equalizer, H7, Inline. Stops, eliminates the light out error from car computer. Easy to install. CE and Rohs listed. Solves, eliminates the problem for headlight or running light or fog light out or driving light out error condition.

9005, 9006 & H10 Warning Canceller, load equalizer. Inline male and female sockets. Eliminates the error on dashboard display for fog or driving light error, or does not turn on the light at all. Plug and play no cutting wires or crimping wires. CE and Rohs listed. Compatible with: 2014 Honda Ridgeline

3157 load equalizer, Fits T25 socket, 6V or 12 VDC systems, eliminates the hyper flash, because the vehicle does not see the LED light. CE and Rohs listed. Gets very hot, must mount on metal surface to help remove the heat from the load equalizer.

Use this T10 194 wedge warning canceller / load equalizer to stop fast flashing, flickering, hyper flashing in your automobile, car, truck, motor cycle. When you replace your approximate 5 to 10 watt incandescent bulb with a lower wattage led light your car will alarm or hyper flash that a bulb is not working but it really is because led lights are so energy efficient. This harness is built so you can install it inline to your current T10 / 194 bulb. Works in 12 Volt vehicles, motorcycles or scooters. .29 Amp normal operating. 12 Volt normal operating. 3.2W normal operating. -40C to 105C normal operating. CE, ISO. LED warning canceller. Has a metal heatsink to keep cooler.

1157 Inline load equalizer. This socket requires no tools for installation. Eliminates the fast flashing after a led light is installed. 12 Volt DC only. This load equalizer has a length of approximately 17.5 inches. Load equalizer measures approximately 3.11 inches by 1.24 inches with a 1 inch thickness. 1157 base measures approximately 1 inch by 0.66 inches. CE and Rohs.

BA15S LED Load Equalizer no tools required to use this inline led load equalizer. Just unplug your light bulb, plug load equalizer where where bulb. Plug the other end into your socket. 12VDC low voltage only. 8 Watt Makes the installation easy and quick to remove your flashing bulb out indicator. This product measures approximately 3.12 inches by 1.23 inches with a 0.96 inch thickness. Socket measures approximately 1.40 inches by 1.40 inches. 1156 or 1129 base measures approximately 1.22 inches by 0.66 inches. CE and Rohs.

H8 & H11 Load equalizer, warning canceller, hyper flash eliminator. For 6 & 12 VDC systems. Use this to get rid of light error on your dashboard computer. CE and Rohs listed.

Used with a LED Light to simulate that the original light bulb is installed. Easy to install. Keep away from plastic or painted surfaces, resistor gets very hot. Includes 7" of 20 awg stranded Teflon wire. 2 wire crimps included. Use one 6 Ohm equalizer for each LED bulb, or use one 3 ohm for 2 led bulbs for each turn signal control side that you replace. Use one 20 Ohm or 100 Ohm for each side marker. For a 6 Ohm load equalizer you can attach up to 1 LED light per equalizer. For the 3 Ohm load equalizer you can attach up to 2 LED lights per equalizer. Load equalizer dimensions are 0.75 inches in length and 0.42 inches wide. (3 ohm equalizer is slightly larger). No special tools needed just a pair of pliers. The connection is made using insulation displacement connectors.

BA9S male to T10 female Load Equalizer Warning Canceler. Use this load equalizer to stop your motorcycle, car, or truck from flashing fast, flickering or hyper flash. Decodes or eliminates the fast flashing.

Used with a LED Light to simulate that the original light bulb is installed. Easy to install. Keep away from plastic or painted surfaces, resistor gets very hot. Includes 7" of 20 awg stranded Teflon wire. 2 wire crimps included. Use one 6 Ohm equalizer for each LED bulb, or use one 3 ohm for 2 led bulbs for each turn signal control side that you replace. Use one 20 Ohm or 100 Ohm for each side marker. For a 6 Ohm load equalizer you can attach up to 1 LED light per equalizer. For the 3 Ohm load equalizer you can attach up to 2 LED lights per equalizer. Load equalizer dimensions are 0.75 inches in length and 0.42 inches wide. (3 ohm equalizer is slightly larger). No special tools needed just a pair of pliers. The connection is made using insulation displacement connectors.

25 Ohm 25 Watt Load Equalizer Low Voltage. Use this load equalizer to fix hyper flash, fast flashing in your car, truck, motorcycle. Works in both 6 Volt and 12 Volt systems. Operates in positive ground or negative ground. Comes with two "IDC" insulation displacement crimps. Use the IDC so you do not have to cut your vehicle wiring. Please just IDC crimps using a pair of plyers. Warning load equalizers get warm or hot to the touch. Please mount to a metal surface.

LED light isolator is used when the brake/turn light control module/switch asserts low signal for negative ground when not active or asserts high signal when not active for positive ground vehicles, trucks and motorcycles. This causes your taillights not to work. Works for 6 Volt, 12 Volt or 24 Volt systems. Works for either positive ground or negative ground vehicles. Isolator rated for 10 Amps. Each isolator can dissipate 60 watts @ 6V, 120 Watts@12V and 240 Watts@24V. To install isolator you must cut brake light wire and splice the isolator inline in the brake light circuit. The wires are stranded 18 AWG. Comes with two I.D.C. insulation displacement connectors. No soldering required using the crimps. The wire length is 5" each side for a total of 10" for both sides. The isolator diameter is approximately .4" diameter and .4" in length.

This will eliminate error codes due to using led bulb that does not have a Canbus controller. Operates at 12 Volt DC. Converts your BA9S male to T10 Wedge female. Rated for 0.29 Amps. Rated for 3.2 Watts. Operating temperature -40C to 105C. Then length is approximately 1.2", the width is approximately 0.679", the depth is approximately 0.37". The overall length is 6", then length on the BA9S side is approximately 1.5", the length on the T10 wedge side is 2.5". The module is made of anodized aluminum. The heatsink is built in to the module case to keep is coolr so it last longer. CE and Rohs certified.

Eliminates BA15S male to T10 female CanBus errors. Rated for 12 Volts, 0.29 Amps, 3.2 Watts. Operating temperature from -40C to 105C. Eliminates CanBus errors when you use a led light that does not have a CanBus controller built in to the led bulb. Approximate size lenght is 1.165", The approximate width is 0.6480" and the approximate depth is 0.372". The overall length is 6". The length to the BA15S socket is approximately 1.5", the length to the T10 Wedge socket is 2.1". CE and Rohs listed.

Use this 6 Ohm 50 Watt led load equalizer to eliminate hyper Flashing is due to the led bulbs are to energy effecient to be detected by the flasher. The flasher thinks there is a bulb out condition and flashes fast to alert the operator that a bulb is burned out. Since led lamps use 1/10th the power of a incandescent bulb the flasher thinks the bulb is burned out even though the led lights. Please use one 6 Ohm per led bulb that is used. Easy test to see if you need a load equalizer is leave one incandescent bulb connected on the left or right circuit. If the flasher flashes normal then you need to use load equalizers to decode or eliminate the fast flashing. This 6 Ohm equalizer is 50 Ohm package so the can dis-pate more power than the 25 Watt. Comes 2 per package. CE Rohs

39 ohm 10 watt Load Equalizer Low Voltage. This load equalizer will fix hyper flashing, fast flashing due to the electronics thinking the incandescent light bulb is not working. Includes two quick crimp connectors. Eliminates OBC error messages.

60 Watt LED Light. Great for driving, running, fog, work, boat, snowmobile, motorcycle lighting. 30 Degree viewing, wide voltage 10-30VDC. White 6000K. Includes stainless steel mounting bracket. Current draw 1.8A @ 12V. 0.9A@24V. Black Enclosure. Up to a 480 watt incandescent equivalent. 1). Cree chip for led work light, high quality. Great for fishing, camping, off road, sight seeing. 2). Easy installation, plug & play. 3). Low heat generation. 4). High brightness low power consumption. 5).

LED Light Bar, 40 Watt, 10-30VDC, Selectable beam spot, or flood, Up to 1800 lumen output, long life up to 30,000 hours, 2 rows of 10 watt LEDs, black aluminum housing, stainless steel mounting hardware included. -40 C to + 60 C operating environment. Comes with 4 10 Watt CREE leds for long life and ultra bright leds.

Tubular Vertical Mounting Bracket 1 1/2 Inch Black. Use for ATV, Truck, Bus, Tow Truck, Motor Cycle, Off road vehicle. Made of black anodized aluminium material.

Mounting Brackets for 1 Inch Tubular bar. Made of black aluminium material. Good to use for ATV, boats, jet skies, bicycles, motor cycles, cars, work trucks, golf cart.

Current draw 1.8A @ 12V. 0.9A@24V LED Work Light 16 x 3 Watt Super Bright LEDs. Wide voltage range 9-30V DC. White 6000 Kelvin. 3155 Lumen output, very bright. Water Proof IP67 rating. Pmma plastic lens. Estimated 30,000 hour life. Diecast aluminum housing. Comes with angled mounting bracket and mounting bolts. Could be used for driving lights, four wheel roll bar LED lights, great for security for cabin, boat or house. 4 3/8" x 4 3/8 x 3". Other applications Cabin/Boat/SUV/Truck/Car/ATVs work truck, tow truck, fire truck, ambulances, police, fishing Deck or fishing dock. Extended warranty, please see product page for warranty information. Comparable to a 350 Watt incandescent light bulb. Since the led light is solid state you do not have to worry about a broken filament or glass. Easy for D.I.Y. installations.

72 Watt L.E.D. compared to a 575 watt incandescent light bar. Up to 4300 lumen output, uses 24 x 3 watt led, Housing Materials: Aluminum, 60 degree viewing angle, wide voltage 10-30 Volt. Includes mounting hardware. Mounting hardware attaches to each side of the light bar for a secure mount. Exterior color is black. IP 67 rated so it is water and dust proof, perfect for exterior lighting on cars, trucks, RVs, and boats. Hooks directly to 10-30 volts using pig tail wires coming out of the back of the light bar.

27 Watt, IP67, 30 Degree, 10-30VDC, White 6000K, CRI>80, Long life up to 30,000 hours. Up to 2200 lumen output. Comparable to a 150-175 watt incandescent light bulb. Great for towing, back up lights, trailer, off road lights, golf cart lights, car lights, fog and so many more uses. Very long life rugged design. Really helps to see when it is dark and since it is led it does not put as much drain on the battery resources. Uses about 2.7 Watts @ 10V.

Use this 27 Watt LED Work Light Low Voltage 10-30V DC IP67 30 Degree for outdoor. IP67 rating, has mounting bracket. White 6500K, upto 1755 lumens. 1.7A@13V,.9A@24V. Diecast aluminum housing. Up to 30000. Very easy to install in most applications. Just drill hole, mount light, hook up electrical wiring to low voltage power source 10V to 30V DC. Has 9 3 watt high power LEDs. Black diecast aluminum housing. Great for off the grid indoor or outdoor lighting. Very long life and durable to be used for off road LED lighting and would also work as driving lights, day time runiing lights. Comes with angled mounting bracket and rugged mounting bolts & nuts. Very nice work light and very nice light to use a headlight for a golf cart or off road vehicle sand rail, dune buggy, jeep or truck, great for back up lights. This light is round in shape.

Off Road Tubular Mounting Bracket Pair Tube Inch Black Finish. Used to mount Off Road L.E.D. Lights to 3 inch tubular bumper. Works good for police, fire, off road, sand dunes, rock climbing, work truck. Made of black anodize aluminium material. Sold as pair, 2 per package.

Current draw 3.8A @ 12V,1.9A @24V. Driving, Work, Fog L.E.D., Up to 3200 lumen output, wide voltage 9-30 volt D.C. Uses 16 3 watt high power LEDs. Comes with mounting hardware. IP 67 rating almost completely water proof. White 6000K and 60 degree beam. Long life up to 30,000 hours. CE and Rohs listed. Comparable to a 400 Watt halogen bulb.

36 Watt LED Light bar. Uses CREE 3 Watt High power leds, long life. Water proof up to 24 hours. 12 volt dc. Kit comes with screws and brackets. 30 Degree beam, spot beam, so objects can be seen at a longer distance and brighter. Long life up to 30,000 hours. CE and Rohs listed. Comparable to a 300 watt incandescent light bulb but only uses 36 watts. The leds are CREE are very bright helps to illuminate the area.

240 LED Light Bar. This water proof light bar has two rows of 40 * 3 watt LED for a total 240 watt output. CRI>80. 12V DC. Light bar comes with brackets to mount it. The light bar uses SPOT beam 30 degree so objects will be lit up better at a longer distance. Comparable to a 1900 watt incandescent, using about 20 Amps of power. Up to 17500 Lumen output.

100 Watt LED Light Bar 10-30V DC IP67 10 * 10W LEDs. Up to 8600 Lumen output. Use this light bar as a work light, driving light, off road light. 1 Foot 5 Inches long and 3.28 Inches wide. Since it is 100 LED watts the comparable incandescent wattage is 100 watt super bright leds. Available in white 6000k only. Made with CREE LEDs for long life. Comparable to a 900 halogen light bulb.

18 Watt LED Driving Light, Work Light, Bike Light 9-32V DC 60 Degree Viewing. Great light for motorcycles, bicycles, cars. Available in white 6000K only. Very compact and powerful 18 watts of LED Lighting. Comparable to a 140 watt incandescent light. Puts out approximately 900 lumens. Measures 6.11" long, 1.81" tall and 2.21" deep. Water proof, made for use on a vehicle.

LED Light bar 72 watt yellow/amber color only. IP67 rated, wide voltage 10-30V DC. Long life up to 30, 000 hours. Combo beam has both narrow 30 degree and wide viewing leds 60 degree. Comes with mounting brackets, screws, nuts, and an allen wrench. CE and ROHS listed. Very easy for DIY installation. Since the led light bar does not have any glass, you can be assured a long trouble free light bar. IP67 works good from protection from mud and water. Up to 6,000 Lumen output. Comparable to 500 watt halogen or incandescent light bulb. Long warranty please see detail page for more details.

Use these brackets to mount the LED off road light bar to the Jeep win shield. Painted black. Comes with mounting hardware. Fits most L.E.D. Off Road lighting.

Tubular Vertical Mounting Bracket 2 Inch Black Pair. Use for work truck, tow trucks, off road vehicles to mount off road l.e.d. lights. Made of black anodize aluminium material.

Off Road Tubular Mounting Bracket Pair Tube 2 1/2 Inch, Black Finish. Used for all terrain vehicles, golf carts, sand buggies, scooters, work trucks and many more applications. Sold as pair, 2 per package.

Tubular mounting bracket for 1 1/4 Inch tubes. Use to mount off road l.e.d. lights. Made of black anodized aluminum material.

1.4-2.0" adjustable Tube mounting bracket for off road led lights. Made of steel with steel finish. Works good for ATV, golf carts, motor cycles, trucks, roll bars, Nerf bars.

Off Road mounting bracket for LED lights. Made of black anodize aluminium material. Uses to mount to 2 inch tube such as a bumper. Used with ATV, Golf Carts, Trucks, Sand buggies, used to light up work area. Sold as a pair, 2 per package

LED Whips. These whips are wrapped with leds. Easy to remove and attach. Come with Bluetooth application so it is compatible with cellular phones. Operates at 12 Volts DC. The choices of size is 4 foot and 5 foot. Comes with the flag. The whip is made with red green and blue leds so you can have all the colors to choose from. The whip is great for off road use at the sand dunes or mud bogs. Easy to install on your motorcycle, rock crawler or sand rail. The flag and the flag mounting hardware is included in the kit. Looks really nice on boats, RV's as a easy way to been seen from a long distance. You have a choice of 4 foot whip or a 5 foot whip. Works in pairs. Really helps out to find your RV at night time using this whip.

Antenna comes in four and five foot lengths. The antenna is controlled by a RF remote to change the RGB colors from red, green and blue to make all colors posible. The whip operates 12 VDC and has about 10 foot hook up wire. Just plus and minus to connect. The whip itself mounts in a hole and comes with mounting hardware. Great for sand rails, ATV, motorcycles and RV's. Works real good to light up your RV at night so it is easier to return to. Comes with a USA flag.

LED RGB Dancing Whip Antenna. Operates 12 Volt DC. Comes with blue tooth remote control. Long life up to 30,000 hours. CE and Rohs listed. Whips come in 4 foot or 5 foot. The whip has red, green and blue leds. The remote or app can choose many different lighting effects. Comes with mounting kit to help the installation goes as smooth as possible. The flag and mounting hardware for flag are included. These whips work great for sand dunes using dune buggy, three wheeler, motorcycle. These whips really are bright to get attention that you are seen in the dark. The remote is wireless so you can change the whips from the drivers seat.

LED Angle Eyes 100 cm Diameter. Great to place around head lights looks very nice. This LED comes equipped with 33 SMT forwad firing LEDs for the angel eyes. 12 Volt. Availabe in white, red, green, blue and amber yellow. Approximate size is 3.92in x .14in with 11in of loose wires for easy installation. Sold Separately. About 15 watt incandescent equivalent.

12 inches. Works with all cars and trucks. Water and shatterproof. Uses standard vehicle power (DC 12V). Available colors are Blue, Red, Green, White, and Yellow. The width is .32 inches and the diameter .060. The LED spacing is .069 inches. The light output is 40 lux per 12 inches. The 12 inches. Requires .26 Amps @13.8 VDC for 12 inches.

LED CHIPS: 116 1/2 watt LEDs. Three color, white, red and amber scan. Fuctions: Driving, Reverse, Brake light, Emergency Hazard, Turn. Material: Flexible Plastic SMOKE color cover and Hard Aluminum Backing. Uses about 58 watts@ 12VDC.

LED CHIPS: 96 1/2 LEDs. Three color, white, red and amber scan. Fuctions: Driving, Reverse, Brake light, Emergency Hazard, Turn. Material: Flexible Plastic SMOKE color cover and Hard Aluminum Backing. See product detail for warranty period. Perfect for any truck in need of a new LED tail light bar

Rechargeable LED trouble/work light. Has stand, rechargeable UL adapter and cigarette lighter plug for use without battery. 90-265V. 10 watts of led white 6000K. Very bright comparable to a 90-100 watt light bulb.

T7 BA7S LED Lamp. Very small BA7S male base. Operates 12 Volt DC only. This LED measures approximately 0.99 inches by .41 inches by 0.31 inches. Available in White 6000 Kelvin, Warm White 3000K, Red(625nm), Green(526nm), Blue(464nm),& Yellow(594nm). This bulb has 5 3 chip 5050 SMT's. Long Life up to 30,000 hours. Full 360 degree viewing angle. Dim-able with a dimmer switch. Comparable to a 15 Watt incandescent bulb. CE and Rohs listed. Compatible with 1980 MGB.

Circular small projecting LED Lights 1 Pair. The kit Angled bracket, double sided sticky tape, mounting screws and approximate 5 feet of wire to hook up to a switch. Each light has 6 LEDs. The led face measures 3 inches by 2 inches with a thickness of about 2.25 inch. Chrome finish. The LED color is white 6000K. Perfect for small, focused lighting needs such as indoor signs, accent lighting, etc.

9 Watt (per bulb) MCOB LED Ultra Bright Daytime Running Lights 12VDC. Very bright LED running lights with adjustable mounting brackets and bolts for easy installation. Metal frame makes for a long lasting durable running light (2 Pack). Available in 6000k white only. Perfect for any vehicle.

The decorative LED Light Rails are 12 volt dc and come with a cigarette lighter power connection (with switch). They come in White, Blue and RGB color change. To mount the LED Light Rails use the two sided adhesive tape to mount it directly to an object or the included, plastic mounting brackets to hook them where you need the Decorative Interior LED Light Rails. One pair comes to a pack that’s two rails connected to a cigarette lighter power adaptor. Great for lighting the floor panel’s, car doors, trunks and the glove box.

LED miniature bulb T1 3/4 midget groove base design the same as the international standard , Midget groove can replace the original Midget groove bulb directly. Approximate size is 16.11 mm length, 5.6 mm diameter. 120 degree viewing angle. The viewing angle is looking down from the top of the bulb. Up to 7 Lumen output. CE and Rohs. Long life up to 30,000 hours. 12 Volt DC.

1895 LED Bulb has 24 Super Flux T10 Wedge BA9S 36 mm Festoon LED Light Bulb. This bulb uses 24 super flux LEDs. The color is white approximate 5500-6500 Kelvin. Low voltage 12 VDC. Has T10 Wedge, BA9S and 36 mm Festoon. Has 3m double sided tape so you can stick this led light almost anywhere. This led measures 2.30 inches by 0.96 inches. Dim-able with a dashboard dimmer switch. Comparable to a 10 to 15 Watt incandescent light bulb. Compatible with 1953 Cessna 170 ba9s light bulbs.

LED Street Rod Light. Great for under car lighting, 12 VDC available in super white, red, green, blue, red and yellow amber. Shatter proof, water resistant. Includes self stick adhesive to mount the street rod led light easily. Also included screws for installation. Only uses .10 mA @ 13.8 VDC. Includes cigarette plug for easy power hookup. The wire length is 6 foot from the tube to the 12 volt power adapter.

T4.7 1 SMT 5050 (3 Chip) LED Light Bulb. Use this T4.7 for A/C instrument panel or dashboards. Up to 6 Lumen output. 12 Volt D.C. Uses very low power, long life. This product measures 0.35 inches by 0.22 inches. Available in only White 6000K. 120 degree viewing angle. Long life up to 30,000 hours. Dim-able with a variable voltage supply such as your dashboard dimmer. CE and Rohs. Compatible with: 5013815aa 4839738aa Neo Wedge 5135537AA 2001-2005 Honda Civic 1990-1997 Honda Accord 2006-2009 Mitsubishi Raider Chrysler 200 2001-2012 Ram 4500 Ram 5500 Ram 3500 Ram Van 3500 Ram Van 2500 Ram Van 1500 1999-2001 Saab 9-3 Intrepid Grand Caravan Dakota Caravan

The LED Valve Stem Cap. Put one on your car, bike, ATV, or motorcycle. When the wheel rotates the LED turns on a strobe light using syntrifical force. So the LED only says on while the means of transport is in motion. The cap itself is Metal and comes in the following colors white, red, green, blue, yellow, ultra violet, and color changing RGB (3LEDs). Comes in 2 per package, with three (6) batteries.

LED Spotlight, Daylight Headlight Wire Kit. Use this kit to install your L.E.D. headlights, spotlights, daylights in your car. Low voltage automotive, motorcycle, jet ski or snowmobile. Comes with 16 feet of 18 AWG stranded wire, inline fuse with 10 amp fuse, 2 quick connect connectors to attach to positive 12 Volt D.C. and ground wires. This kit is enough parts to provide 100 watts of power for one LED light circuit.

T3 1 1210 S.M.D. L.E.D. Light. Use this T3 LED Light for instrument panel led lighting. Up to 6 Lumen output. The T3 has 1 1210 (3528) SMT LED Light. Great to help reduce failures in instrument panels. Available in White 6000K only. Dim-able. 120 degree viewing angle. Long life up to 30,000 hours. 12 Volt DC.

T4.2 1 3528 SMD LED Light Bulb. Use this T4.2 LED Light bulb to replace lights in instrument panels. 12 Volts D.C. The LED Bulb has one 1210 (3528) SMT LED. Available in White 6000K. This product measures 0.38 inch by 0.33 inches. Up to a 6 Lumen output. Comparable to a 4 to 9 Watt incandescent light bulb. 120 degree viewing angle. Up to 30,000 hour life. Dim-able with your dashboard dimmer. CE and Rohs.

42mm 8 1210 SMD LED Lighting with Hook. 42mm in length. Has hooks on each end. has 8 1210 SMT LEDs. 12 Volt DC. Available in white only. #561 replacement. Very bright, very nice replacement. Up to 140 Lumen output. 120 degree viewing angle. Dimmable with a variable voltage supply such as your dashboard dimmer switch. Uses .1 amp @ 13.8 Volts DC. Uses up to 1.40 Watts. Long life up to 30,000 hours. Comparable to a 10 to 15 Watt incandescent. Compatible with: 1971-1973 Ford Mustang Mach 1

BA5S LED Light. Has one led. Operates 12 Volt DC. Fits a BA5S Socket. Available only in white. This LED measures approximately 0.62 inches by 0.22 inches. Dimmable range from 2.5 volts to 13.8 volts. Comparable to a 4 to 9 Watt incandescnet bulb. Viewing angle 120 degrees. CE and Rohs.

T8 Wedge LED Light. Available in white only. 12 Volt DC. Uses approximately .25 Watts @ 12 VDC. long life up to 25,000 hours. CRI>80.

The 8 Ultra-Bright Chrome Projector Automotive LED Puck Light is a great interior accent light. It throws cool blue color LED light where you want it. Each LED puck Light has 5 feet of wire and adhesive tape to make installing the puck lights a breeze. You just have to wire them in to your cars electrical system. The puck lights are great for limos, tucks, cars, 18 wheelers, tractors trailers anywhere there is 12 volts of power DC you can use the Chrome LED Puck Lights. 1 Pair. Includes mounting screws.